Hanwell MS1000 Manuel utilisateur

hanwell.com

GD6063

MS1000 Control System

Installation Guide

Intentionally Left Blank

MS1000 Control System

Installation Guide

hanwell.com Page 1 of 31 GD6063-1

Document History

Document Number: GD6063

Issue No. Issue Date Changes By

1 26 October 2018

Changes to take account of introduction

of EMS and reformatting IR

MS1000 Control System

Installation Guide

GD6063-1 Page 2 of 30 hanwell.com

Contents

1Overview of the MS1000 Control System....................................................................... 4

2MS1000 Control System Configuration .......................................................................... 5

2.1Option 1 - Standalone Solution...................................................................................................... 5

2.2Option 2 - Monitoring and Control Solution .............................................................................. 6

2.2.1Controllers/Processors ...............................................................................................................7

2.3Output Cards...................................................................................................................................... 8

2.3.1Output Card Specifications ...................................................................................................... 11

3Pre-Delivery........................................................................................................................12

4Firmware/Software Requirements..................................................................................13

4.1Firmware ............................................................................................................................................ 13

4.2Software ............................................................................................................................................. 13

4.2.1New Systems............................................................................................................................... 13

4.2.2Existing Systems......................................................................................................................... 13

5Pre-Commissioning...........................................................................................................14

6MS1000 Output Card ID Number................................................................................... 15

6.1ID Number .........................................................................................................................................15

6.1.1Setting the ID Number ..............................................................................................................15

7Connecting the MS1000 Control System...................................................................... 16

7.1Power Supply.................................................................................................................................... 16

7.2Controller to MS1000 Control Unit - USB Cable Wiring........................................................ 17

7.3RS485 Wiring from Controller to MS1000 Control Unit ........................................................ 17

7.3.1Standalone MS1000 Systems................................................................................................. 17

7.3.2Monitoring and Control Systems ........................................................................................... 17

7.3.3Wiring Summary ........................................................................................................................20

7.3.4Customer Supplied Wiring Required Specifications .......................................................20

7.4Wiring the Output Cards ................................................................................................................21

8Technical Reference ........................................................................................................22

MS1000 Control System

Installation Guide

hanwell.com Page 3 of 30 GD6063-1

8.1MS1000 Enclosures ....................................................................................................................... 22

8.1.1Standard Case (Code N001) .................................................................................................. 22

8.1.2Large Case (Code N016)......................................................................................................... 22

8.1.3Extra Large Case (Code N051) .............................................................................................. 22

8.1.4MS1000 Output Card Case .................................................................................................... 23

8.2Allowable Temperature and Humidity Ranges ...................................................................... 23

9Hanwell MS1000 System Fault Checking.....................................................................24

9.1Signals are not being received on any channels .................................................................. 24

9.2Signals are not being received on some channels............................................................... 25

9.3Readings are incorrect.................................................................................................................. 26

10Existing Hanwell EMS Users........................................................................................... 27

10.1Hardware .......................................................................................................................................... 27

10.2Software............................................................................................................................................ 27

10.2.1Wiring ........................................................................................................................................... 27

11Contact Information.........................................................................................................28

MS1000 Control System

Installation Guide

GD6063-1 Page 4 of 30 hanwell.com

1Overview of the MS1000 Control System

The Hanwell MS1000 Control System is an interface between a Hanwell Environmental

Monitoring System (EMS) and 3rd party control equipment.

It is designed to generate either latched voltages or currents corresponding to inputs,

proportional to measured values, generated by sensors, in remote locations, that are

compatible with the Hanwell Environmental Monitoring System (EMS) software.

Typical applications could include:

Interfacing radio sensors to a Building Management System (BMS).

Conservation heating systems.

Bespoke heating control.

Providing signals to an Alarm Panel.

The MS1000 Control System can:

Allow radio sensors to directly replace wired-in sensors in applications such as building

environmental control where the 3rd party BMS can directly accept analogue signals.

Trigger relay outputs for alarm or control functions (e.g. motorised valves).

Provide a combination of all output types within a single MS1000 system.

MS1000 Control System

Installation Guide

hanwell.com Page 5 of 30 GD6063-1

2MS1000 Control System Configuration

There are two main options for configuring the MS1000 Control System:

Standalone Solution

Monitoring and Control Solution

2.1 Option 1 - Standalone Solution

Radio sensors transmit directly back to the MS1000 Control Unit via either a standalone

Receiver connected to the MS1000 or a receiver incorporated into the MS1000 Control

Unit.

The MS1000 Control Outputs are sent to, for example, a 3rd Party Building Management

System (BMS).

Figure 1 - Stand Alone Solution Schematic

MS1000 Control System

Installation Guide

GD6063-1 Page 6 of 30 hanwell.com

2.2 Option 2 - Monitoring and Control Solution

Radio sensors transmit to an SR2 or CR2 Controller/Processor/Base Station (Controller).

The Controller sends the data to both a monitoring PC and the MS1000 Control Unit.

The MS1000 Control Outputs are sent to, for example, a Building Management System

(BMS). See Figure 2 below:

Sensor 1’s output controls Plant A.

Sensor 2’s output controls Plants B and C.

Note: In some applications, the Controller may be enclosed within the MS1000 Control Unit;

the Controller PCB being either in a separate Control Unit or mounted within the

MS1000’s Control Unit, depending on the exact system supplied.

Figure 2 - Monitoring and Control Solution Schematic

MS1000 Control System

Installation Guide

hanwell.com Page 7 of 30 GD6063-1

Figure 3 – General System Schematic

2.2.1 Controllers/Processors

The CR2 and SR2 Controllers both provide an interface/controls for the MS1000 Control

System in addition to their other functions as outlined in Sections 2.2.1.1 and Error! Reference

source not found. below.

2.2.1.1 Hanwell CR3

The CR3 Controller receives and processes data signals from Hanwell radio and wired

sensors and is designed for continuous monitoring of an entire system.

Received data is then logged and stored, pending transfer to a PC for analysis and

archival storage.

The CR3 also signals alarm conditions via the front panel LEDs (should any sensor

measure above or below individual pre-set levels).

Although the CR3 Controller has an extensive memory capacity, it is intended that the

data is transferred to a PC for detailed interpretation and permanent storage. This can

be done automatically or manually, at any time.

A built in GSM modem for remote communications is also available.

MS1000 Control System

Installation Guide

GD6063-1 Page 8 of 30 hanwell.com

2.2.1.2 Hanwell SR2

The SR2 Hanwell Smart Receiver/Controller is a network enabled receiver, designed for

continuously monitoring environmental data from multiple points within a site, or across

multiple sites, receiving and processing data signals from Hanwell radio and wired sensors.

Additionally, the SR2 can be fitted with up to eight onboard probes and can be upgraded to a

transceiver to both receive and re-transmit the data.

Each SR2 can handle data from up to 253 sensors and, as up to 16 SR2s can be run on a

single system, up to 4048 sensors can be connected to a single system.

The SR2 logs all received data in its on-board 512kb memory.

The software continually interrogates the SR2 for the most recent data and downloads

the data according to user-defined logging periods to the server or operating PC from

where software users can view live and historic data, produce out of specification and

summary reports and set alarms for both the data values and the rate of change of the

data’s values.

An optional remote Receiver can be connected to improve radio reception in difficult

areas.

Alarm relays are included: these can indicate that the readings are out of specification

and can, optionally, be set to indicate a network failure.

An MS BUS connection allows the SR2 to drive the Hanwell MS1000 Control System.

2.3 Output Cards

Input signals generated by sensors are either passed directly to the MS1000 Control System

or passed to a CR3 or SR2 Controller for processing, before transmission to the MS1000

Control System.

Output signals from the MS1000 Control System to the systems/equipment under control are

generated by Output Cards located within the MS1000 Control Unit.

Table des matières

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur