Hanna Instruments PHep+ HI 98108 Manuel utilisateur

pHep®+

HI 98108

Pocket-sized pH Meter

with ATC

IST98108 R3 05/05

pHep®+is a rugged pH tester with replace-

able electrode and renewable reference junction.

The instrument can be calibrated at two points

by the user, simply acting on the offset and slope

calibration trimmers. In addition, the Automatic

Temperature Compensation feature enhables high

accuracy in measurements.

pHep®+is in compliance with the CE direc-

tives.

SPECIFICATIONS

Range 0.0 to 14.0 pH

Resolution 0.1 pH

Accuracy (@20°C/68°F) ±0.1 pH

Typical EMC Deviation ±0.1 pH

Calibration Manual, 2 point, through

offset and slope trimmers

Temperature Compensation

Automatic, 0 to 50°C

Environment 0 to 50°C (32 to 122°F);

RH max 95%

Battery Type 4 x 1.5V alkaline

Battery Life approx. 200 hours of use

Dimensions 175 x 41 x 23 mm

(6.9 x 1.6 x 0.9")

Weight 95 g (3.4 oz.)

ACCESSORIES

HI 73108 Spare electrode

HI 7004M pH 4.01 solution, 230 mL bottle

HI 7007M pH 7.01 solution, 230 mL bottle

HI 7010M pH 10.01 solution, 230 mL

HI 70300M Storage solution, 230 mL bottle

HI 7061M Cleaning solution, 230 mL bottle

HI 731326 Calibration screwdriver (20 pcs)

pHep is a registered Trademark of

Hanna Instruments

www.hannainst.com

Pull out 2 mm (1/8'') of the cloth

junction to renew the electrode refer-

ence (it is recommended to cut the

cloth leaving always at least 2 mm -

1/8'' over the reference compartment)

and recalibrate the meter.

The cloth junction can be pulled out approximately 20

times. After that, the electrode should be replaced.

ELECTRODE REPLACEMENT

For replacing the electrode, contact your Dealer or the nearest

Hanna Service Center.

BATTERY REPLACEMENT

If calibration can not be performed or the display fades,

batteries must be replaced. Slide off the battery compart-

ment cover and replace all four 1.5V alkaline batteries,

while paying attention to the correct polarity.

Batteries should only be replaced in a non-hazardous area

and using the battery type specified in this instruction

manual.

CONDITIONING

• Remove the cap.

• To activate the electrode, immerse it in HI70300

storage solution for 2 hours.

CALIBRATION

• Immerse the electrode in pH 7.01 (HI7007) buffer

solution.

• Allow the reading to stabilize and

with the supplied screwdriver, ad-

just the “pH7” calibration trimmer

to read “7.0” pH.

• Rinse the electrode with tap water

and immerse it into the second

buffer.

• Use pH 4.01 (HI7004) if the solution to be measured

is acidic (pH < 7), or pH 10.0 (HI7010) for alka-

line samples (pH > 7).

• Allow the reading to stabilize and with the screwdriver

adjust the “pH4/10” calibration trimmer to read “4.0”

or “10.0” pH.

OPERATION

• Remove the protective cap, turn the

pHep®+on, by sliding the ON/

OFF switch on the top of the meter.

• Immerse it in the solution to be

tested without exceeding the maxi-

mum immersion level.

• Stir gently and wait for the reading

to stabilize.

• After use, switch the meter off, rinse the electrode with

tap water and store it with a few drops of storage

(HI70300) or pH7 (HI7007) solution in the protec-

tive cap. Always replace the protective cap after use.

NEVER USE DISTILLED OR DEIONIZED WATER FOR STOR-

AGE PURPOSES.

• Large differences in pH readings (±1 pH) could be

due to lack of calibration or dry electrode.

MAINTENANCE

The sensor should be kept moist at all times. For this

purpose, always keep wet the tissue inside the protective

cap. In case of erroneous readings even after an accurate

conditioning and calibration, the reference junction might

be contaminated or clogged.

WARRANTY

This meter is guaranteed for one year against defects in

workmanship and materials when used for their intended

purpose and maintained according to instructions. This war-

ranty is limited to repair or replacement free of charge.

Damages due to accident, misuse, tampering or lack of

prescribed maintenance are not covered. If service is re-

quired, contact the dealer from whom you purchased the

instrument. If under warranty, report the model number,

date of purchase, serial number and the nature of the fail-

ure. If the repair is not covered by the warranty, you will be

notified of the charges incurred. If the instrument is to be

returned to Hanna Instruments, first obtain a Returned Goods

Authorization Number from the Customer Service depart-

ment and then send it with shipment costs prepaid. When

shipping any instrument, make sure it is properly packaged

for complete protection.

Autres manuels Hanna Instruments Instrument de mesure

Hanna Instruments

Hanna Instruments HI1006-18 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 120 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 96701C Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 9210N Manuel utilisateur

Hanna Instruments

Hanna Instruments Chromium VI Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 93729 Manuel utilisateur

Hanna Instruments

Hanna Instruments Checker HI 711 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 95729C Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 721 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 981402 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI84531 Manuel utilisateur

Hanna Instruments

Hanna Instruments Foodcare HI981035 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 991300 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI96746C Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 1285-5 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 2209 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 93720 Manuel utilisateur

Hanna Instruments

Hanna Instruments Champ HI 98106 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 9829 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI97700 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 93716 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI97714 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 8314 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 99191 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur

Hanna Instruments pHep+ HI 98108 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques