Hanna Instruments HI 96831 Manuel utilisateur

Instruction Manual

HI 96831

Ethylene Glycol Refractometer

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the

Remove the instrument from the packing materials and examine carefully to ensure no

damage has occurred during shipping. If any damage has occurred, notify your Dealer.

Each instrument is supplied with:

• 9 V battery

• Instruction manual

Note:Save all packing material until you are sure that the instrument functions

correctly. A defective instrument must be returned in its original packing.

Dear Customer,

Thank you for choosing a Hanna product. This manual will provide you with the necessary

information for the correct use of this instrument. Please read it carefully before using the meter.

TABLE OF CONTENTS

PRELIMINARY EXAMINATION

PRELIMINARY EXAMINATION ............................................................................................. 2

GENERAL DESCRIPTION ..................................................................................................... 3

SPECIFICATIONS .................................................................................................................. 3

PRINCIPLE OF OPERATION ................................................................................................ 4

MEASUREMENT UNITS ........................................................................................................ 5

FUNCTIONAL DESCRIPTION................................................................................................ 5

DISPLAY ELEMENTS............................................................................................................ 6

MEASUREMENT GUIDELINES .............................................................................................. 7

CALIBRATION PROCEDURE ................................................................................................ 7

MEASUREMENT PROCEDURE ............................................................................................. 8

TO CHANGE MEASUREMENT UNIT ..................................................................................... 9

TO CHANGE TEMPERATURE UNIT ...................................................................................... 9

MAKING A STANDARD SOLUTION....................................................................................10

BATTERY REPLACEMENT .................................................................................................10

WARRANTY ........................................................................................................................10

ERROR MESSAGES ............................................................................................................11

GENERAL DESCRIPTION

SPECIFICATIONS

Temperature Compensation: Automatic between 0 and 40 °C (32 - 104 °F)

Measurement Time: Approximately 1.5 seconds

Minimum Sample Volume: 100 μL (cover prism totally)

Light Source: Yellow LED

Sample Cell: Stainless Steel ring and flint glass prism

Case Material: ABS

Enclosure Rating: IP 65

Battery Type / Life: 1 X 9V / 5000 readings

Auto-Off: After 3 minutes of non-use

Dimensions: 19.2(W) x 10.2(D) x 6.7(H) cm

Mass: 420 g

The HI 96831 Digital Refractometer is a rugged portable, water resistant device that utilizes the

measurement of refractive index to determine the % volume and freezing point of ethylene glycol

based coolants or antifreeze.

The HI 96831 device benefits from Hanna’s years of experience as a manufacturer of analytical

instruments. The digital refractometer eliminates the uncertainty associated with mechanical

refractometers and is easily portable for use in the field to optimize your cooling system.

The HI 96831 refractometer is an optical device that is simple and quick to use. Samples are

measured after a simple user calibration with distilled or deionized water. Within seconds, the

refractive index and temperature are measured and converted into one of two measurement units;

% Volume or Freezing Point. The instrument utilizes internationally recognized references for unit

conversion and temperature compensation for ethylene glycol solutions (e.g. CRC Handbook of

Chemistry and Physics, 87th Edition).

The temperature (in °C or °F) is also displayed on the large dual level display along with helpful

message codes.

Key features include:

• IP65 waterproof protection

• Automatic Temperature Compensation (ATC)

• Battery operation with Low Power indicator (BEPS)

• Automatically turns off after 3 minutes of non-use

emuloV%tnioPgnizeerF)F°(C°

:egnaR %001ot0)F°85-ot23(C°05-ot0)F°671ot23(C°08ot0

:noituloseR %1.0)F°1.0(C°1.0)F°1

.0(C°1.0

:ycaruccA %2.0±)F°0.1±(C°5.0±)F°5.0±(C°3.0±

Ethylene Glycol determinations are made by measuring the refractive index of a solution. Refractive

Index is an optical characteristic of a substance and the number of dissolved particles in it.

Refractive Index is defined as the ratio of the speed of light in empty space to the speed of light in

the substance. A result of this property is that light will “bend”, or change direction, when it travels

through a substance of different refractive index. This is called refraction.

When passing from a material with a higher to lower refractive index, there is a critical angle at

which an incoming beam of light can no longer refract, but will instead be reflected off the interface.

The critical angle can be used to easily calculate the refractive index according to the equation:

sin (θcritical) = n2/ n1

Where n2is the refractive index of the lower-density medium; n1is the refractive index of the

higher-density medium.

In the HI 96831 refractometer, light from an LED passes through a prism in contact with the sample.

An image sensor determines the critical angle at which the light is no longer refracted through the

sample. Specialized algorithms then apply temperature compensation to the measurement and

convert the refractive index to: % Volume or Freezing Point.

PRINCIPLE OF OPERATION

MEASUREMENT UNITS

Freezing point is displayed as a temperature from 0.0 to -50.0 °C corresponding to 0-58 % by

volume. The display blinks the freezing point when the concentration of Ethylene glycol is greater

than 78 % concentration by volume.

When the display shows “LO”, the freezing point is at a minimum (below -50 °C).

FUNCTIONAL DESCRIPTIONFUNCTIONAL DESCRIPTION

FUNCTIONAL DESCRIPTION

1. Liquid Crystal Display (LCD)

2. READ Key (User Measurement)

3. ZERO Key (User Calibration)

4. RANGE Key (User Measurement Unit)

5. ON/OFF

6. Stainless Steel Sample Well and Prism

7. Secondary Display

8. Primary Display

TOP VIEW

DISPLAY ELEMENTSDISPLAY ELEMENTS

DISPLAY ELEMENTS

1. Battery (blinks when low battery condition detected)

2. Measurement in Progress Tag

3. SETUP: Factory Calibration Tag

4. CAL: Calibration Tag

5. Automatic Temperature Compensation

(blinks when temperature exceeds 0-40°C / 32-104°F range)

6. Primary Display (displays measurement and error messages)

7. Temperature Units

8. Secondary Display (displays temperature measurements; when blinking,

temperature has exceeded operation range: 0-80°C / 32-176°F)

9. Range indicator

9. Battery Cover

10.Battery Compartment

BOTTOM

• Handle instrument carefully. Do not drop.

• Do not immerse instrument under water.

• Do not spray water to any part of instrument except the “sample well” located over the prism.

• The instrument is intended to measure ethylene glycol solutions. Do not expose instrument or

prism to solvents that will damage it. This includes most organic solvents and extremely hot

or cold solutions.

• Particulate matter in a sample may scratch the prism. Absorb sample with a soft tissue and

rinse sample well with deionized or distilled water between samples.

• Use plastic pipettes to transfer all solutions. Do not use metallic tools such as needles, spoons

or tweezers as these will scratch the prism.

• Cover sample well with hand if measuring in direct sun.

MEASUREMENT GUIDELINESMEASUREMENT GUIDELINES

MEASUREMENT GUIDELINES

CALIBRATION PROCEDURECALIBRATION PROCEDURE

CALIBRATION PROCEDURE

Calibration should be performed daily, before measurements are made, when the battery has

been replaced, between a long series of measurements, or if environmental changes have

occurred since the last calibration.

1. Press the ON/OFF key, then release. Two instrument test screens will be displayed briefly;

all LCD segments followed by the percentage of remaining battery life. The meter will then

briefly display an indication of the measurement unit set. When the LCD displays dashes, the

instrument is ready.

2. Using a plastic pipette, fill the sample well with distilled or deionized water. Make sure the

prism is completely covered.

Note: If the ZERO sample is subject to intense light such as sunlight or another strong source,

cover the sample well with your hand or other shade during the calibration.

MEASUREMENT PROCEDUREMEASUREMENT PROCEDURE

MEASUREMENT PROCEDURE

Verify the instrument has been calibrated before taking measurements.

1. Wipe off prism surface located at the bottom of the sample well. Make sure the prism and

sample well are completely dry.

2. Using a plastic pipette, drip sample onto the prism surface. Fill the well completely.

Note: If the temperature of the sample differs significantly from the temperature of the

instrument, wait approximately 1 minute to allow thermal equilibration.

3. Press the READ key. The

results are displayed as %

Volume or Freezing Point.

Note: The last measurement value will be displayed until the next sample is measured or the

instrument is turned off. Temperature will be continuously updated.

Note: The ”ATC”tag blinks and automatic temperature compensation is disabled if the

temperature exceeds the 0-40 °C / 32-104 °F range.

3. Press the ZERO key. If no error messages appear, your unit is calibrated.

(For a description of ERROR MESSAGES see page 11).

Note: The 0.0 screen will remain until a sample is measured or the instrument is turned off.

4. Gently absorb the ZERO water standard with a soft tissue. Use care not

to scratch the prism surface. Dry the surface completely. The instrument

is ready for sample measurement.

Note: If the instrument is turned off the calibration will not be lost.

4. Remove sample from the sample well by absorbing

with a soft tissue.

5. Using a plastic pipette, rinse prism and sample

well with distilled or deionized water. Wipe dry.

The instrument is ready for the next sample.

TO CHANGE MEASUREMENT UNITTO CHANGE MEASUREMENT UNIT

TO CHANGE MEASUREMENT UNIT

Press the RANGE key to select the measurement units. The instrument toggles between the

two measurement scales each time the key is pressed and the primary display indicates “Vol”

% Volume or “FrPt” for Freezing Point. When the instrument displays the screen with 4 dashes,

the instrument is ready for measurement. A number on the display indicates the selected unit: “1”

denotes % Volume and “2” denotes Freezing Point (as indicated on the instrument cover).

Note: The temperature measurement is not displayed in Freezing Point mode.

8 seconds

TO CHANGE TEMPERATURE UNITTO CHANGE TEMPERATURE UNIT

TO CHANGE TEMPERATURE UNIT

To change the temperature measurement unit from Celsius to Fahrenheit (or vice versa), follow this

procedure.

1. Press and hold the ON/OFF key continuously for approximately 8 seconds. The LCD will

display the “all segment” screen followed by a screen with the model number on the primary

display and the version number on the secondary display. Continue pressing the ON/OFF

key.

2. While continuing to hold the ON/OFF key, press the ZERO key. The temperature unit will

change from °C to °F or vice versa.

Note: The selected unit will be used in Freezing Point mode.

To make a Ethylene Glycol Solution, follow the procedure below:

•To make an X % ethylene glycol solution volumetrically add X mL of high purity ethylene

glycol (CAS #: 107-21-1; MW 62.068) to a 100 mL Grade A volumetric flask.

•Use distilled or deionized water to bring the flask close to the total volume, mix, allow the

solution to return to room temperature.

•Once the solution has returned to room temperature use distilled or deionized water to bring

the total volume to 100 mL. Mix solution well before use.

WARRANTYWARRANTY

WARRANTY

The HI 96831 is warranted for two years against defects in workmanship and materials when

used for its intended purpose and maintained according to the instructions.

This warranty is limited to repair or replacement free of charge.

Damage due to accidents, misuse, tampering or lack of prescribed maintenance is not covered.

If service is required, contact your dealer. If under warranty, report the model number, date of

purchase, serial number and the nature of the failure. If the repair is not covered by the warranty,

you will be notified of the charges incurred.

If the instrument is to be returned to Hanna Instruments, first obtain a Returned Goods Authorization

Number from the Customer Service Department and then send it with shipment costs prepaid. When

shipping any instrument, make sure it is properly packaged for complete protection.

To validate your warranty, fill out and return the enclosed warranty card within 14 days from the

date of purchase.

locylGenelyhtEemuloVlatoTeulaVtnioPgnizeerFdetcepxE

V%01 Lm00.01Lm00.001)F°2.52(C°8.3-

V%04 Lm00.04Lm00.001)F°4

.51-(C°3.62-

MAKING A STANDARD SOLUTIONMAKING A STANDARD SOLUTION

MAKING A STANDARD SOLUTION

To replace the instrument’s battery, follow these steps:

• Make sure the instrument is off.

• Turn instrument upside down and remove the battery cover by turning it counterclockwise.

• Extract the battery from its location.

• Replace with a new 9V battery making sure to observe polarity.

• Insert the back battery cover and fasten it by turning clockwise to engage.

BATTERY REPLACEMENTBATTERY REPLACEMENT

BATTERY REPLACEMENT

Autres manuels pour HI 96831

Table des matières

Autres manuels Hanna Instruments Instrument de mesure

Hanna Instruments

Hanna Instruments HI97746 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 701 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 2400 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI9812-51 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 93102 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 761 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI96720C Manuel utilisateur

Hanna Instruments

Hanna Instruments HUALIX HI 715 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 991001 Manuel utilisateur

Hanna Instruments

Hanna Instruments HALO 2 HI9810342 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 99181 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 5315 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 98191 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 84102 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 95759 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 83208 Manuel utilisateur

Hanna Instruments

Hanna Instruments Checker HI717 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI764 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 746 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI96711C Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 96770C Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 8734 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 96700 Manuel utilisateur

Hanna Instruments

Hanna Instruments HI 96770 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur