HALNy HL-4G Manuel utilisateur
Quick Installation Guide
GPON ONT
HALNY HL-4G
HALNy HL-4G Quick Installation Guide
2
Safety Guidance
1.1 Safety Check
Before installing the device, you must check the following items.
1.1.1 Electric Safety
⚫Ensure that there are no inflammable, conductive or moist objects around.
Check whether the cables are aged and whether other electrical appliances
are placed stably,
⚫Check whether the alternating or direct input current is within the allowed
range of the device, whether the polarity of the direct current is correct, and
whether the earth line is properly connected.
1.1.2 Device Position
⚫Because the running electric device easily generates heat, please ensure to
place the device in a well-ventilated environment,
⚫Avoid direct sunshine, and do not place the device on a PC case,
⚫Keep the device away from heat and water,
⚫Check whether power supply is available. The input voltage fluctuation range
must be smaller than 10%. The power plug should not share one socket with
a hair drier, an iron or a refrigerator.
1.2 Safety Caution
⚫Read the quick installation guide carefully before using the device,
⚫Note all Cautions in the quick installation guide,
⚫Do not use any accessory that does not belong to the device without prior
consent of the manufacture, as it may cause fire or product damage,
⚫Use the power adapter accompanied in the package,
⚫Do not place any object on the device,
⚫Keep the device dry, ventilated, rainproof, and clean,
⚫During lightning weather, unplug the power plug and all connection cables, to
protect the device against lightning,
HALNy HL-4G Quick Installation Guide
3
⚫Clean the device using a soft and dry cloth rather than liquid or atomizers.
Power off the device before cleansing it,
⚫Power off the idle device,
⚫Keep the ventilation hole clean and prevent any object from dropping into the
device through it. Otherwise, it may cause short circuit and further cause
device damage or fire. Do not spray liquid on the surface of the device,
⚫Do not open the case of the device, especially during device power-on,
⚫Before plugging or unplugging the power, ensure that the power is off, thus
avoiding surge,
⚫Be careful when unplugging the power, as the transformer may be very hot,
⚫Cover the optical interface with fiber interface cap when it is not in use. Avoid
direct eye exposure to the laser emitted from the optical interface. Wear safety
glasses if possible, to protect your eyes.
Caution:
Please read the above safety guidance carefully before device use.
Users should assume responsibilities for any accidents due to
incompliance with the above instructions.
2 Overview
This chapter mainly describes functions and the structure of the HALNy HL-4G.
2.1 Features and Function
⚫Fast rate. Support up to 1.25Gbps uplink and 2.5Gbps downlink data
transmission rates,
⚫Strong maintainability. Provide various statuses of LED indicators, to help
troubleshooting,
⚫Long transmission distance, up to 20 km.
HALNy HL-4G Quick Installation Guide
4
2.2 Front, Rear and bottom Panel
The description of the front panel and the rear panel of the GPON ONU as follows.
2.2.1 Front Panel
Fig. 1 - Front Panel
LED
Color
Status
Description
POWER
Green
On
The power works normally.
Off
Powered off or the power supply is abnormal.
PON
Green
Refer to Table 2: “PON LED Status Instruction”
LOS
Red
Refer to Table 2: “PON LED Status Instruction”
Internet
Green
On
Got WAN IP Address Successfully
Blink
Data is being transmitted
Off
Device in bridged mode or no IP
LAN1-4
Green
On
The connection of Ethernet interface is normal.
Blink
Data is being transmitted through the Ethernet interface.
Off
The connection of the Ethernet interface fails to
establish.
Off
The connection of the Ethernet interface fails to
establish.
Table 1. ONU LED Indication Table
HALNy HL-4G Quick Installation Guide
5
Table 2.PON LED Status Instruction
2.2.2 Rear Panel
Fig 2. Rear Panel
ONU Rear Panel Description：
Interface /
Button
Function
LAN1-4
Ethernet interface, for connecting to a computer or an Ethernet
interface of a switch.
RST
Press the button for 5 seconds to reboot ONU and restore the factory
default configurations.
Power
Connect power cable
ON/OFF
Turn on/off the power supply.
Table 3.Rear Panel port description
PON LED Status Instruction
PON
LOS
Description
Off
Off
The ONT is disabled by the OLT
Flash
Off
The ONT is registering to the OLT
On
Off
The ONT has already registered to OLT
Off
Flash
The fiber is not connected properly
HALNy HL-4G Quick Installation Guide
6
2.2.3 Bottom Panel
Fig 3 Bottom Panel
ONT Bottom Panel Description：
Interface
Function
SC/APC
GPON interface for connecting to a SC/APC patchcord
3 ONU Installation
The chapter describes the required installation operations beforeyou use the device
for the first time.
3.1 Product Networking Application - FTTH
Fiber to the Home (FTTH) means to install the ONU to residences or enterprise
buildings. The optical line terminal (OLT) is placed in the central equipment room.
The ONU can be placed in the home of a user, or it can provide connection for the
user through the Ethernet interface, according to the user requirement. The OLT
connects to the ONU with an optical distributor in the point-to-multipoint way. See
the following figure.
FTTH
HALNy HL-4G Quick Installation Guide
7
Note：
The ONU applies to installation at home or in the corridor. Because installation and
cabling in the corridor are relatively complex, let the professional engineers deploy
according to the actual situation. This manual describes the procedure for installing the
device at home, and is for reference only.
3.2 Installation Preparations
The Ethernet interface of your computer connects to the Ethernet interface of the
ONU. Before installingit, ensure that an Ethernet adapteris already installed inyour
computer.
3.3 Connecting ONU
3.3.1 Connecting the Network Cable
Step 1 Use the one end of the network cable to connect the Ethernet interface of
the computer.
Step 2 Use other end of a network cable to connect the Ethernet interface on the
rear panel of the HALNy HL-4G.
HALNy HL-4G Quick Installation Guide
8
3.3.2 Connecting the Fiber
Caution:
⚫When a fiber is not in use, ensure to cover the optical interface of the ONU and
the dust cap of the optical fiber. Prevent grease, dust pollution or water
immersion, which may lead to unavailable fiber and optical interface of the
device.
⚫If fibers need to be fixed or bended during cabling, do not fasten the fibers too
tight. Avoid fiber extrusion, which may lead to increase of fiber material or
unavailable fiber.
3.2.3 Connecting the Power Adapter and Power Cord
⚫Connect the output end of the power adapter included in the device package to
the input end of the power supply of the ONU ,
⚫Insert one end of the power cord attached with the device into the input end of
the power adapter. Insert the other end of the power cord into the power socket,
⚫Check whether the Power indicator is on. If it is on, the power supply is normal.
Otherwise, check whether the power cord and the power adapter are correctly
connected.
HALNy HL-4G Quick Installation Guide
9
4 Troubleshooting
Symptom
Solution
The POWER
indicator is not on
Check whether the power connection is correct,
Check whether the power adapter matches the
device.
The PON indicator is
not on
Check whether the SN of ONU matches OLT,
Check whether the optical attenuation is in the normal
range.
The LOS indicator is
not on
Check whether the optical fiber cable is properly
inserted,
Check whether the optical fiber connector is clean.
The LAN indicators
are not on
Check whether the PC NIC is enabled,
Check whether the network cables included in the
device package are used,
Check whether the network cable connection is
normal,
Check whether the indicator of the network adapter is
on,
Check whether the network adapter works in the
normal state.
HALNy HL-4G Quick Installation Guide
10
5 Technical Specification
Main Technical Specifications
Standard
GPON Standard
ITU-T G.984
Rate
Uplink
1.25Gbps
Downlink
2.5Gbps
Interface
One optical interface
Single Mode
4 LAN port
RJ-45 10/100/1000Mbps MDI/MDIX Self
adaption
Physical Characteristics and Environment Requirements
Power adapter input
100V～240V AC，50Hz～60Hz
Whole-device power supply
12V DC 0.5A/1 A
Standard power consumption
<6W
Operating temperature
0˚C～45˚C
Operating humidity
10%~90% (non-condensing）
Dimension
L x W x H：200mm x 138mm x 38mm
Weight
<300g
Appendix A Acronyms and Abbreviations
GPON
Gigabit Passive Optical Network
FTTB
Fiber to the Building
FTTH
Fiber to the Home
OLT
Optical Line Terminal
ONU
Optical Network Unit
PON
Passive Optical Network
Table des matières
Autres manuels HALNy Routeur réseau
HALNy
HALNy HL-4GQVS Manuel utilisateur
HALNy
HALNy GPON ONT HL-4BX3V-F Manuel utilisateur
HALNy
HALNy HL-4GXV-F Manuel utilisateur
HALNy
HALNy GPON ONT HL-1GR Manuel utilisateur
HALNy
HALNy HL-2BV Manuel utilisateur
HALNy
HALNy HLE-3GX-F Manuel utilisateur
HALNy
HALNy HL-1GE Manuel utilisateur
HALNy
HALNy HL-4GQV Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité