Halma Ocean Optics TR2 Manuel utilisateur

Engineering Note

Topic: TR2 Information

Product Affected: TR2 Temperature Regulator, S2000 Spectrometer

Date Issued: 8/29/2002

Operation

The TR2 is a Temperature Regulator unit that stacks onto the S2000 Spectrometer. The TR2 displays

two temperature values (in oC), the set temperature and actual temperature. The TR2 has two controls,

a set point pushbutton and a toggle switch. The display can toggle between viewing the actual

temperature and the set-point temperature. With the pushbutton pushed out, the display shows the

actual temperature. The set-point temperature is viewed by pressing the pushbutton in.

The temperature is set by a digitally controlled potentiometer with 100 set points. To adjust the set-

point, press the pushbutton and then increment or decrement the toggle switch to the desired

temperature. The set-point is stored in a volatile memory location. To store the set point permanently,

press the toggle switch to the down position and then press the set button. This action will lock the set

temperature into permanent memory.

A standard TR2 can be adjusted between 0°C and 37°C. However the TR2 is only capable operating

15°C below the ambient temperature. At cool temperatures, the operator must insure that

condensation does not occur on the inside of the optical bench. By design, the maximum

temperature set-point is 37°C.

The TR2 requires a regulated +12V power supply that delivers at least 2 amps. Poor results may be

obtained if a non-regulated power supply or a supply that cannot deliver adequate current is used. The

power connection is configured for a positive center polarity.

The TR2 indicates its status with a two color LED. The status conditions are defined as follows:

• Green – The TR2 has reached temperature stability (within 0.1oC).

• Red – The TR2 has not reached temperature stability.

• Blinking Red – The TR2 is not running. Reset by pushing the pushbutton.

The S2000-TR2 system operates from two power supplies: the 5V from the ADC Card and the +12V

from the external power supply. Depending on the order in which power is applied, the TR2 may

power-up with a blinking red LED. To clear the blinking LED, press the pushbutton to reset the unit.

209-00000-000-04-0704 1

TR2 Information Engineering Note

Pin Out

The TR2 interfaces to the S2000 using the H1 & H2 connectors. The pin-out for these signals is show

below. In addition, the TR2 has a J3 connector that communicates the various temperature signals. Its

pin-out is shown in Table 1 below.

When Multiple S2000-TR2 assemblies are stacked together, several signals in the J3 connector must

be connected among all of the TR2 boards in the stack. The Table 1 below defines these signals. In

this condition, the display will only show the actual and set-point temperatures from a single unit.

Typically, this unit is the Master Spectrometer Channel.

Table 1: J3 Definition

Pin Signal Name Connections Description

1 N/C No Connect

2 VTEMP From one TR2

(Master) Analog signal of the current temperature. Scaling is

100mv/oC

3 Reset All Reset signal for TR2—Active Low

4 VSET From one TR2

(Master) Set-point temperature signal to be displayed when

pushbutton is depressed. Scaling is 100mv/oC)

5 Ground All +5V Ground

6 Vdisplay From one TR2

(Master) Analog Signal that is displayed. Scaling is 100mv/oC

7 Toggle Down All Clock signal to toggle the set-point down one increment—

Active Low

8 N/C No Connect

9 Ground All +5V Ground

10 Toggle Up All Clock signal to toggle the set-point up one increment—

Active Low

2 209-00000-000-04-0704

TR2 Information Engineering Note

Table 2: S2000-H1 Header Pins (Analog) Table 3: S2000-H2 Header Pins (Digital)

1 Analog Channel 0 D N/C

2 Analog Channel 1 C A/D Trigger

3 Analog Channel 2 B Software Trigger In (D3)

4 Analog Channel 3 A Trigger Mode Select (S1)

5 Analog Channel 4 1 GND

6 GND 2 +5 VDC

7 Reserved 3 F Clock

8 Analog Channel 7 4 Readout Gate

9 Analog Channel 6 5 Reserved

10 Analog Channel 5 6 Temperature (optional)

7 Read Enable

8 Trigger Mode Select/Strobe Enable

(S0)

9 Single Strobe Out

10 Continuous Strobe Out

11 Integration Clock

12 Master Clock

TR2 Control Signals

It is possible to drive the control signals (Toggle Up/Down and Reset) directly. These signals are 5V

TTL Active LOW signals that are pulled HIGH on the TR2 board.

To change the current set point, drive the Reset signal LOW and then pulse the Toggle Up or Toggle

Down LOW. Each falling edge of the Toggle Up/Down signal will drive the set point one position in

the desired direction. Once the desired set point is reached, drive (or release) the Toggle Up/Down

signals HIGH and then drive (or release) the Reset signal HIGH. The Toggle Up/Down signals are de-

bounced on each TR2 and the minimum pulse width is 100ns. There is no maximum pulse width.

To change the nonvolatile power-up set point, hold the Toggle Up/Down signal LOW while the Reset

signal is driven (or released) HIGH. This writes the current wiper setting to the nonvolatile memory

location that is read from upon power-up of the unit.

209-0000-000-04-0704 3

TR2 Information Engineering Note

4 209-00000-000-04-0704

Ce manuel convient aux modèles suivants

Autres manuels Halma Instrument de mesure

Halma

Halma Ocean Optics NIRQuest512-1.7 Manuel utilisateur

Halma

Halma ALICAT IM Manuel utilisateur

Halma

Halma ALICAT SCIENTIFIC L Manuel utilisateur

Halma

Halma Ocean Optics LASER-785-IP-LAB Manuel utilisateur

Halma

Halma Alicat Scientific CODA KM Manuel utilisateur

Halma

Halma ALICAT SCIENTIFIC M Series Fiche technique

Halma

Halma ALICAT SCIENTIFIC L Manuel utilisateur

Halma

Halma ALICAT SCIENTIFIC L Manuel utilisateur

Halma

Halma Ocean Optics HR2000 Series Manuel utilisateur

Halma

Halma ALICAT SCIENTIFIC MB Series Fiche technique

Halma

Halma Ocean Optics QE65 Pro Manuel utilisateur

Halma

Halma Alicat Scientific L Manuel utilisateur

Halma

Halma Ocean Optics JAZ Manuel utilisateur

Halma

Halma ALICAT SCIENTIFIC L Manuel utilisateur

Halma

Halma SENSITRON SMART S Manuel utilisateur

Halma

Halma Ocean Optics Maya2000Pro Series Manuel utilisateur

Halma

Halma Sensitron SMART 3 NC Manuel utilisateur

Halma

Halma Ocean Optics DH-mini UV-Vis-NIR Manuel utilisateur

Halma

Halma Alicat Scientific L Manuel utilisateur

Halma

Halma ALICAT SCIENTIFIC MB Manuel utilisateur

Halma

Halma ALICAT BC Series Manuel utilisateur

Halma

Halma Alicat Scientific CORIOLIS CODA Series Manuel utilisateur

Halma

Halma PERMA PURE Baldwin Series Manuel utilisateur

Halma

Halma ALICAT SCIENTIFIC MB Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur