H3C S12500 Series Manuel utilisateur

H3C S12500 Routing Switch Series

Quick Start Guide

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6PW101-20120508

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H3Care, , TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V2G, VnG, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage,

use, and disposal of this product must meet the applicable national laws and regulations.

Contents

Quick start guide·························································································································································· 1

Preparing for installation ··················································································································································1

ESD prevention ·························································································································································1

Examining the installation site·································································································································1

Installation tools and accessories ···························································································································2

Installing the switch ···························································································································································2

Installing the switch in a rack··································································································································2

Grounding the switch···············································································································································5

Installing the power modules···································································································································6

Installing a fan tray ··················································································································································8

Installing a card························································································································································9

Connecting power cords ······································································································································ 12

Verifying the installation ······································································································································· 15

Logging in to the switch················································································································································· 15

Connecting the console cable······························································································································ 15

Powering on the switch········································································································································· 16

Obtaining documentation ············································································································································· 17

Index ···········································································································································································18

Quick start guide

NOTE:

This quick start guide provides basic instructions for installing an S12500 routing switch. For more

detailed installation procedures, see

H3C S12500 Routing Switch Series Installation Guide

Preparing for installation

ESD prevention

To prevent the electronic components from being damaged by the electrostatic discharge (ESD), always

wear an ESD-preventive wrist strap when you touch the switch, cards, or ICs, and make sure that the wrist

strap is well grounded.

Figure 1 Attaching an ESD-preventive wrist strap

Examining the installation site

The H3C S12500 Routing Switch Series can only be used indoors. To make sure that the switch works

properly and to prolong its service lifetime, the installation site must meet the load-bearing, temperature,

humidity, cleanness, EMI, grounding, power module, and space requirements. For more information, see

H3C S12500 Routing Switch Series Installation Guide:

Installation tools and accessories

Installing the switch

Figure 2 Installation flow

Installing the switch in a rack

Check before installation

Before installation, make sure that the bottom edge of the slide rails or rack shelf aligns with the middle

of the narrower metal area between holes.

Phillips screwdriver

(user-supplied)

Cage nut

(required)

End

Verify the installation

Start

Install the switch in a rack

Ground the switch

Install power supplies Install a fan tray Install cards

Connect the power cords

Figure 3 Installing the slide rails

(1) Middle of the narrower metal area between holes (2) 1 RU

Installing cage nuts

1. Align the mounting bracket with the left rack post, making sure that the bottom edge and the slide

rail are level. Mark the positions of the cage nuts on the rack post according to the installation

holes on the mounting bracket (each installation hole on the mounting bracket corresponds to one

cage nut).

2. Insert one edge of a cage nut into the hole.

3. Compress the other edge of the cage nut to push the cage nut fully into the hole.

4. Repeat steps 2 and 3 to install cage nuts to all the marked positions on the right rack post.

Figure 4 Installing the cage nuts



Installing the mounting brackets

Figure 5 Installing the mounting brackets (for the S12504)

Figure 6 Installing the mounting brackets (for the S12508/S12518)

Mounting the switch in the rack

1. Use several people to place the switch on the slide rails or rack shelf and slide the switch into the

rack until the mounting brackets on the switch touch the front rack posts.

2. Fix the mounting brackets to the cage nuts on the rack posts with mounting screws.

Figure 7 Installing the switch in a standard 19-inch rack

Grounding the switch

1. Remove the two grounding screws from the switch chassis.

2. Use the grounding screws to attach one end of the grounding cable to the chassis.

3. Connect the other end of the grounding cable to the grounding strip of the rack in the same way.

Figure 8 Connecting the grounding cable

Installing the power modules

NOTE:

H3C recommends that you install at least three power modules to one power frame.

Installing a DC power module

1. Rotate the power frame cover up with both hands.

2. Pull the clip at the bottom left corner of the power module to the left to open the power module

panel.

3. Insert the power module slowly into the slot until it is firmly seated in the slot.

4. Close the panel of the power module, press the clip to lock the power module in position, and

close the power frame cover.

Figure 9 Installing a power module

Installing an AC power module

To install an AC power module, install a PEM first, and then install the AC power module.

To install a PEM:

1. Loosen the screws on the filler panel of the PEM slot with a Phillips screwdriver to remove the filler

panel.

2. Insert a PEM slowly along the slide rails until it touches the backplane connector.

3. Use the M3 screws supplied with the PEM to fix the PEM to the switch chassis, and fasten the

screws with a Phillips screwdriver.

Autres manuels pour S12500 Series

Table des matières

Autres manuels H3C Changer

H3C

H3C S9500 Series Instructions d'installation

H3C

H3C S12500X-2L Manuel utilisateur

H3C

H3C S5560S-EI Series Manuel utilisateur

H3C

H3C S5820 series Manuel d'installation

H3C

H3C S5560X-30C-EI Manuel utilisateur

H3C

H3C H3C S5100-SI Manuel utilisateur

H3C

H3C S5830V2 series Manuel utilisateur

H3C

H3C S5830 Series Manuel utilisateur

H3C

H3C UniServer BX1010E Manuel utilisateur

H3C

H3C S5510 Series Manuel utilisateur

H3C

H3C S3100V3-EI Series Manuel utilisateur

H3C

H3C S9500 Series Instructions d'installation

H3C

H3C S5120-SI Series Manuel utilisateur

H3C

H3C S6800 Series Manuel utilisateur

H3C

H3C S5830 Series Manuel utilisateur

H3C

H3C S5510 Series Manuel utilisateur

H3C

H3C S9500 Series Manuel utilisateur

H3C

H3C S5170-EI Series Manuel utilisateur

H3C

H3C LSW1SP4P0 Manuel utilisateur

H3C

H3C S3610 Series Instructions d'installation

H3C

H3C S9500 Series Manuel utilisateur

H3C

H3C S10500X Series Manuel utilisateur

H3C

H3C S6805 Series Manuel utilisateur

H3C

H3C HSW-2024G Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur