H3C A3600 Series Manuel utilisateur

HP A3600 Series Ethernet Switches

Installation Manual

Organization

HP A3600 Series Ethernet Switches Installation Manual is organized as follows:

Chapter Contents

1 Product Overview Introduces the characteristics and technical

specifications of S3600 Series Ethernet Switches.

2 Preparation Introduces the installation preparation and

precaution of S3600 Series Ethernet Switches.

3 Installation Introduces the procedures to install an S3600 Series

Ethernet Switch, including the setup of the

mainframe, cards and cables.

4 Starting up the Switch at the Initial Boot Introduces the booting process of an S3600 Series

Ethernet Switch, including the power-on booting of

the switch and the system initialization.

5 Loading Boot ROM and Host Software Introduces how to load BootROM and host software

for an S3600 Series Ethernet Switch.

6 Maintenance and Troubleshooting Introduces the problems that might occur during the

installation and the booting of an S3600 Series

Ethernet Switch and the related solution.

7 Appendix Lightning Protection of the Switch Introduces lightning protection of S3600 Series

Ethernet Switches.

Conventions

The manual uses the following conventions:

I. GUI conventions

Convention Description

< > Button names are inside angle brackets. For example, click <OK>.

[ ] Window names, menu items, data table and field names are inside square

brackets. For example, pop up the [New User] window.

/Multi-level menus are separated by forward slashes. For example,

[File/Create/Folder].

II. SymbolsConvention Description

Warning Means reader be extremely careful. Improper operation may cause bodily

injury.

Caution Means reader be careful. Improper operation may cause data loss or

damage to equipment.

Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and

disposal of this product, national laws and regulations must be observed.

Chapter 1 Product Overview

1.1 Introduction

HP S3600 Series Ethernet Switches developed by HP are high-performance, high-density, easy-to-install, NMS-manageable

intelligent Ethernet switches which support wire-speed Layer 2/3 switching.

Table 1-1 lists the models of HP S3600 Series Ethernet Switches.

Table 1-1 Models of the S3600 series

Subseries Model Power

supply

Number of

service

ports

Number of

100 Mbps

ports

Number of 1000

Mbps uplink ports

Number of

Console

ports

HP A3600-SI

A3600-24

SI AC 28 24 × 10Base-

T/100Base-TX

Ethernet ports

4 × 1000Base-X

SFP ports 1

A3600-

24TP SI AC 28 24 × 10Base-

T/100Base-TX

Ethernet ports

2 × 1000Base-X

SFP ports, 2 ×

10/100/1000Base-

T Ethernet ports

A3600-48

SI AC 52 48 × 10Base-

T/100Base-TX

Ethernet ports

4 × 1000Base-X

SFP ports 1

HP A3600-

POE-SI

A3600-

24-POE

SI AC/DC 28 24 × 10Base-

T/100Base-TX

Ethernet ports

4 × 1000Base-X

SFP ports 1

A3600-

48-POE

SI AC/DC 52 48 × 10Base-

T/100Base-TX

Ethernet ports

4 × 1000Base-X

SFP ports 1

HP A3600-EI

A3600-24

EI AC/DC 28 24 × 10Base-

T/100Base-TX

Ethernet ports

4 × 1000Base-X

SFP ports 1

A3600-

24-SFP EI AC/DC 28 24 x 100Base-

X SFP ports

2 × 1000Base-X

SFP ports, 2 ×

10/100/1000Base-

T Ethernet ports

A3600-48

EI AC/DC 52 48 × 10Base-

T/100Base-TX

Ethernet ports

4 × 1000Base-X

SFP ports 1

HP A3600-

POE-EI

A3600-

24-POE

EI AC/DC 28 24 × 10Base-

T/100Base-TX

Ethernet ports

4 × 1000Base-X

SFP ports 1

A3600-

48-POE

EI AC/DC 52 48 × 10Base-

T/100Base-TX

Ethernet ports

4 × 1000Base-X

SFP ports 1

Note:

The A3600-24-POE SI, A3600-24-POE EI, A3600-48-POE

SI, and A3600-48-POE EI provides over-temperature

protection mechanism. When the internal temperature exceeds

65°C (149°F), they will stop providing power from all ports.

When the temperature is below 60°C (140°F), they will

continue to provide power from all ports.

Only the recommended PoE power supply can be used for

the A3600-24-POE SI, A3600-24-POE EI, A3600-48-POE SI,

and A3600-48-POE EI. The –48 VDC from the equipment room

cannot be used directly. Otherwise, devices may be damaged.

1.2 A3600-24 SI

1.2.1 Front Panel

I. Schematic diagram

The A3600-24 SI provides twenty-four 10Base-T/100Base-TX auto-sensing Ethernet ports, four 1000Base-X SFP ports, and

one Console port on the front panel, as shown in Figure 1-1.

(1) 10Base-T/100Base-TX auto-sensing Ethernet port status LEDs

(2) 1000Base-X SFP port status LEDs (3) AC power LED

(4) Mode LED (5) Mode button

(6) 7-segment digital LED (7) Console port

Figure 1-1 Front panel of the A3600-24 SI

II. LEDs

The A3600-24 SI provides one AC power LED, one mode LED, one 7-segment digital LED, twenty-four 10Base-T/100Base-TX

auto-sensing Ethernet port status LEDs, and four 1000Base-X SFP port status LEDs on the front panel. You can learn how the

switch operates by observing the LEDs listed in Table 1-2.

Table 1-2 LEDs on the front panel of the A3600-24 SI

LED Mark Status Indication

Mode LED Mode

Speed Solid green Rate information of 10Base-T/100Base-TX

auto-sensing Ethernet ports, and

1000Base-X SFP ports

Duplex Solid yellow Duplex information of 10Base-T/100Base-

TX auto-sensing Ethernet ports, and

1000Base-X SFP ports

AC Power

LED PWR

Solid green The switch is started normally.

Flashing green (1 Hz) The system is running a power-on self-test

(POST) or downloading software.

Solid red The system fails a POST or a fault occurs.

Flashing yellow (1 Hz) Some ports fail a POST or malfunctions

occur.

OFF The power is disconnected.

10Base-

T/100 — Speed Green ON A 100 Mbps link is present.

LED Mark Status Indication

Base -TX

port status

LED

Flashing Data is being received/sent on the port.

Yellow ON A 10 Mbps link is present.

Flashing Data is being received/sent on the port.

Flashing yellow (3

Hz) The port fails the POST.

OFF No link is present.

Duplex

Green ON The port is operating in full duplex mode.

Flashing Data is being received/sent on the port.

Yellow ON The port is operating in half duplex mode.

Flashing Data is being received/sent on the port.

Flashing yellow (3

Hz) The port fails the POST.

OFF No data is being received/sent on the port.

1000

Base-SFP

port status

LED

—

Speed

Green ON A 1000 Mbps link is present.

Flash Data is being received/sent on the port.

Flashing yellow (3

Hz) The port fails POST.

OFF No link is present.

Duplex

Green ON The port is operating in full duplex mode.

Flash Data is being received/sent on the port.

Flashing yellow (3

Hz) The port fails the POST.

OFF The port is not connected.

PoE mode

Flashing green (3

Hz) The port fails the POST.

OFF ––

Status

LED of the

1000Base-

X SFP

port

serving as

a fabric

port

—

Speed

Green ON The port is connected, and the device is in

an IRF loop fabric.

Flashing Data is being received/sent on the port.

Yellow ON The port is connected, and the device is in

an IRF chain fabric.

Flash Data is being received/sent on the port.

Flashing green (3Hz) A fault occurs to Fabric.

Flashing yellow (3

Hz) The port fails the POST.

OFF The port is not connected.

Duplex Green ON The port is in full duplex mode.

Flashing Data is being received/sent on the port.

LED Mark Status Indication

Flashing yellow (3

Hz) The port fails the POST.

OFF The port is not connected.

PoE

Flashing yellow (3

Hz) The port fails the POST.

OFF ––

7-segment

digital LED Unit

POST

running The PWR LED

flashes green Displays the POST test ID (in the range of

1 to 9).

POST failed

The PWR LED

flashes yellow Flashes the POST test ID of the failed test.

The PWR LED is

solid red

Software

downloading The PWR LED

flashes green A bar rotates clockwise around the LED.

Fan failed The PWR LED is

solid red Displays “F”.

Unit ID Button released Displays the unit ID in the fabric; and

displays “1” if there is only one unit.

III. Attributes of the 10Base-T/100Base-TX Ethernet ports

Table 1-3 Attributes of the 10Base-T/100Base-TX Ethernet Ports on the A3600-24 SI

Attribute Description

Connector RJ-45

Number of ports 24

Rate

10 Mbps, half duplex/full duplex

100 Mbps, half-duplex/full duplex

MDI/MDI-X auto-sensing

Standard IEEE 802.3u

Transmission distance over the

selected medium 100 m (328.08 ft) over the category-5 unshielded twisted pair (UTP)

cable

IV. Console port

The A3600-24 SI provides one EIA/TIA-232 compliant Console port for local or remote configuration. Table 1-4 lists the

attributes of the Console port.

Table 1-4 Console port attributes

Attribute Description

Connector RJ-45

Standard Asynchronous EIA/TIA-232

Baud rate 9600 bps (default)

Attribute Description

Service

Connection to the ASCII terminal

Connection to the serial interface of a local terminal (a PC for example) or to a remote

terminal through a pair of modems), where terminal emulation program is run

V. Attributes of the 1000Base-X SFP ports

The A3600-24 SI provides four 1000Base-X SFP ports (numbered from 25 to 28) on its front panel.

SFP modules allow for great flexibility because they are hot swappable and user configurable.

Table 1-5 lists the available SFP modules.

Table 1-5 1000Base-X SFP modules

Type Model

SFP optical

module

1000Base-X SFP module

SFP-GE-SX-MM850-A

SFP-GE-LX-SM1310-A

SFP-GE-LH40-SM1310

SFP-GE-LH40-SM1550

SFP-GE-LH70-SM1550

SFP electrical interface

module SFP-GE-T

Note:

The types of 1000Base-X SFP modules may be subject to

changes without notice. Consult HP marketing personnel or

technical support personnel to obtain the latest information

about SFP modules.

For specifications of SFP modules, refer to HP Low End

Series Ethernet Switches Pluggable Modules Manual.

1.2.2 Rear Panel

I. Schematic diagram

The A3600-24 SI provides an AC power socket and a grounding screw on its rear panel, as shown in Figure 1-2.

(1) AC power socket (2) Grounding screw

Figure 1-2 Rear panel of the A3600-24 SI

II. Power system

The following gives the input voltage specifications for the A3600-24 SI:

Rated voltage range: 100 VAC to 240 VAC, 50/60 Hz

Input voltage range: 90 VAC to 264 VAC, 47 to 63 Hz

1.3 A3600-24TP SI

1.3.1 Front Panel

I. Schematic diagram

The A3600-24TP SI provides twenty-four 10Base-T/100Base-TX auto-sensing Ethernet ports, two 1000Base-X SFP ports, two

10/100/1000Base-T auto-sensing Ethernet ports, and one Console port on the front panel, as shown in Figure 1-3.

(1) 10Base-T/100Base-TX auto-sensing Ethernet port status LEDs

(2) 1000Base-X SFP port status LEDs

(3) 10/100/1000Base-T auto-sensing Ethernet port status LEDs

(4) Console port

(5) 7-segment digital LED (6) AC power LED

(7) Mode LED (8) Mode button

Figure 1-3 Front panel of the A3600-24TP SI

II. LEDs

The A3600-24TP SI provides one power LED, one DC power LED, one mode LED, one 7-segment digital LED, twenty-four

10Base-T/100Base-TX Ethernet port status LEDs, two 1000Base-X SFP port status LEDs, and two 10/100/1000Base-T auto-

sensing Ethernet port status LEDs. You can learn how the switch operates by observing the LEDs listed in Table 1-6.

Table 1-6 LEDs on the front panel of the A3600-24TP SI

LED Mark Status Indication

AC power

LED PWR

Solid green The switch is started normally.

Flashing green (1Hz) The system is running a POST or

downloading software.

Solid red The system fails the POST or a fault occurs.

Flashing yellow (1Hz) Some ports fail a POST or malfunctions

occur.

OFF The power is disconnected.

Mode LED Mode Speed Solid green Rate information of 10Base-T/100Base-TX

Ethernet ports, and 1000Base-X SFP ports.

LED Mark Status Indication

Duplex Solid yellow Duplex information of 10Base-T/100Base-

TX Ethernet ports, and 1000Base-X SFP

ports.

10Base-

T/100Base-

TX port

status LED

—

Speed

Green ON A 100 Mbps link is present.

Flashing Data is being received/sent on the port.

Yellow On A 10 Mbps link is present.

Flashing Data is being received/sent on the port.

Flashing yellow

(3Hz) The port fails a POST.

OFF No link is present.

Duplex

Green ON The port is operating in full duplex mode.

Flashing Data is being received/sent on the port.

Yellow ON The port is operating in half duplex mode.

Flashing Data is being received/sent on the port.

Flashing yellow

(3Hz) The port fails a POST.

OFF No data is being received/sent on the port.

1000Base-

X SFP port

status LED —

Speed

Green ON A 1000 Mbps link is present.

Flashing Data is being received/sent on the port

Flashing yellow

(3Hz) The port fails a POST.

OFF No link is present.

Duplex

Green ON The port is operating in full duplex mode.

Flashing Data is being received/sent on the port.

Flashing yellow

(3Hz) The port fails a POST.

OFF No link is present.

PoE

Flashing green

(3Hz) The port fails a POST.

OFF —

10/100/

1000Base-

T Ethernet

port status

LED

—

Speed

Green ON A 1000 Mbps link is present.

Flashing Data is being received/sent on the port.

Yellow ON A 10/100 Mbps link is present.

Flashing Data is being received/sent on the port.

Flashing yellow

(3Hz) The port fails a POST.

OFF No link is present.

Duplex Green ON The port is operating in full duplex mode.

Flashing Data is being received/sent on the port.

LED Mark Status Indication

Yellow ON The port is operating in half duplex mode.

Flashing Data is being received/sent on the port

Flashing yellow

(3Hz) The port fails POST.

OFF No data is being received/sent on the port.

7-segment

digital LED Unit

POST

running The PWR LED

flashes green Displays the POST test ID (in the range of 1

to 9).

POST

failed

The PWR LED

flashes yellow Flashes the POST test ID of the failed test.

The PWR LED is

solid red

Software

loading The PWR LED

flashes green A bar rotates clockwise around the LED.

Fan failure The PWR LED is

solid red Displays “F”.

Unit ID Button released Displays the unit ID in the fabric, and

displays “1” if there is only one unit.

III. Attributes of the 10Base-T/100Base-TX Ethernet ports

The A3600-24TP SI provides twenty-four 10Base-T/100Base-TX Ethernet ports (numbered from 1 to 24) on the front panel. For

attributes of these ports, see Table 1-3.

IV. Attributes of the 1000Base-X SFP ports

The A3600-24TP SI provides two 1000Base-X SFP ports numbered 25 and 26 on the front panel.

SFP modules allow for great flexibility because they are hot swappable and user configurable.

Table 1-5 lists the available SFP modules.

Note:

The types of 1000Base-X SFP modules may be subject to

changes without notice. Consult HP marketing personnel or

technical support personnel to obtain the latest information

about SFP modules.

For specifications of SFP modules, refer to HP Low End

Series Ethernet Switches Pluggable Modules Manual.

V. Attributes of the 10/100/1000Base-T Ethernet ports

The A3600-24TP SI can provide two 10/100/1000Base-T Ethernet ports numbered 27 and 28 on the front panel. For attributes

of these two ports, see Table 1-7.

Table 1-7 Attributes of the 10/100/1000Base-T Ethernet ports on the A3600-24TP SI

Attribute Description

Connector RJ-45

Number of ports 2

Table des matières

Autres manuels H3C Changer

H3C

H3C S12500X-AF Series Manuel utilisateur

H3C

H3C S7504E-XS Manuel d'utilisation et d'entretien

H3C

H3C S5500-SI Series Manuel utilisateur

H3C

H3C S7500E-XS Series Manuel utilisateur

H3C

H3C Mini Series Manuel utilisateur

H3C

H3C H3C S7500E Series Manuel utilisateur

H3C

H3C s5820x series Manuel d'installation

H3C

H3C S9820-64H Manuel d'utilisation et d'entretien

H3C

H3C S9500 Series Manuel utilisateur

H3C

H3C S9500 Series Manuel utilisateur

H3C

H3C S5820V2H Manuel utilisateur

H3C

H3C S5120-EI Series Manuel utilisateur

H3C

H3C S6800-4C Manuel d'utilisation et d'entretien

H3C

H3C S9850-4C Manuel d'utilisation et d'entretien

H3C

H3C IE4300-12P-PWR Manuel utilisateur

H3C

H3C S9500 Series Manuel utilisateur

H3C

H3C H3C S7500E Series Manuel d'installation

H3C

H3C UniServer BX608FE Manuel utilisateur

H3C

H3C S6826 Series Manuel utilisateur

H3C

H3C S5170-EI Series Manuel du propriétaire

H3C

H3C SECPATH 5080F-CMW710-R9628P2414 Comment utiliser

H3C

H3C S5560S-SI Manuel utilisateur

H3C

H3C S3100V2-52TP Manuel utilisateur

H3C

H3C s5820x series Manuel d'installation

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur