H3C LSWM12H2Q Manuel utilisateur

H3C LSWM12H2Q interface card user

manual-6PW102

▌Introduction

Overview

The LSWM12H2Q interface card provides two QSFP28 ports and two

QSFP+ ports.

Figure 1 Front panel

(1) QSFP+ port LED (2) QSFP28 port LED

(3) QSFP28 port (4) QSFP+ port

QSFP+ ports

You can install the following transceiver modules and cables in the

QSFP+ ports on the card:

•QSFP+ transceiver modules in Table 1 and Table 2.

•QSFP+ DAC cables in Table 3.

•QSFP+ to SFP+ DAC cables in Table 4.

•QSFP+ AOC cables in Table 5.

Table 1 QSFP+ transceiver modules available for the QSFP+

ports (1)

QSFP+ transceiver module Central

wavelength (nm) Connector

QSFP-40G-SR4-MM850 850 MPO

QSFP+ transceiver module Central

wavelength (nm) Connector

QSFP-40G-CSR4-MM850 850 MPO

QSFP-40G-LR4-WDM1300

Four lanes:

•1271

•1291

•1311

•1331

QSFP-40G-LR4L-WDM1300

Four lanes:

•1271

•1291

•1311

•1331

Table 2 QSFP+ transceiver modules available for the QSFP+

ports (2)

QSFP+

transceiver

module

Cable/fiber

diameter

(µm)

Modal

bandwidth

(MHz × km)

Max transmission

distance

QSFP-40G-S

R4-MM850

Multi-mode,

50/125

2000 100 m (328.08 ft)

4700 150 m (492.12 ft)

QSFP-40G-C

SR4-MM850

Multi-mode,

50/125

2000 300 m (984.25 ft)

4700 400 m (1312.33 ft)

QSFP-40G-LR

4-WDM1300

Single-mode,

9/125 N/A 10 km (6.21 miles)

QSFP-40G-LR

4L-WDM1300

Single-mode,

9/125 N/A 2 km (1.24 miles)

Table 3 QSFP+ DAC cables available for the QSFP+ ports

QSFP+ DAC cable Cable length Data rate

LSWM1QSTK0 1 m (3.28 ft)

40 Gbps

LSWM1QSTK1 3 m (9.84 ft)

LSWM1QSTK2 5 m (16.40 ft)

Table 4 QSFP+ to SFP+ DAC cables available for the QSFP+

ports

QSFP+ to SFP+ DAC cable Cable length Data rate

LSWM1QSTK3 1 m (3.28 ft)

40 Gbps

LSWM1QSTK4 3 m (9.84 ft)

LSWM1QSTK5 5 m (16.40 ft)

Table 5 QSFP+ AOC cables available for the QSFP+ ports

QSFP+ AOC cable Cable length Data rate

QSFP-40G-D-AOC-7M 7 m (22.97 ft)

40 Gbps

QSFP-40G-D-AOC-10M 10 m (32.81 ft)

QSFP-40G-D-AOC-20M 20 m (65.62 ft)

NOTE:

s a best practice, use H3C QSFP+ transceiver modules, QSFP+

DAC cables, QSFP+ to SFP+ DAC cables, and QSFP+ AOC

cables for the QSFP+ ports on the LSWM12H2Q interface card.

The H3C QSFP+ transceiver modules and QSFP+ cables

available for the card are subject to change over time. For the

most recent list of H3C QSFP+ transceiver modules and QSFP+

cables available for the card, contact H3C Support or marketing

staff.

For more information about H3C QSFP+ transceiver modules and

QSFP+ cables, see H3C Transceiver Modules User Guide at

www.h3c.com.

QSFP28 ports

You can install the following transceiver modules and cables in the

QSFP28 ports on the card:

•QSFP+ transceiver modules in Table 1 and Table 2.

•QSFP+ DAC cables in Table 3.

•QSFP+ AOC cables in Table 5.

•QSFP28 transceiver modules in Table 6 and Table 7.

•QSFP28 DAC cables in Table 8.

Table 6 QSFP28 transceiver modules available for the QSFP28

ports (1)

QSFP28 transceiver

module

Central

wavelength (nm) Connector

QSFP-100G-SR4-MM850 850 MPO (PC

polished, 12-core)

QSFP-100G-LR4-WDM13

Four lanes:

•1295

•1300

•1304

•1309

Table 7 QSFP28 transceiver modules available for the QSFP28

ports (2)

QSFP+

transceiver

module

Cable/fiber

diameter

(µm)

Modal

bandwidth

(MHz × km)

Max

transmission

distance

QSFP-100G-S

R4-MM850

Multi-mode,

50/125 4700 100 m (328.08 ft)

QSFP-100G-LR

4-WDM1300

Single-mode,

9/125 N/A 10 km (6.21

miles)

Table 8 QSFP28 DAC cables available for the QSFP28 ports

QSFP28 DAC cable Cable length Data rate

QSFP-100G-D-CAB-1M 1 m (3.28 ft)

100 Gbps

QSFP-100G-D-CAB-3M 3 m (9.84 ft)

NOTE:

s a best practice, use H3C QSFP+/QSFP28 transceiver modules

and QSFP+/QSFP28 DAC cables for the QSFP28 ports on the

LSWM12H2Q interface card. The H3C QSFP+/QSFP28

transceiver modules and QSFP+/QSFP28 DAC cables available

for the card are subject to change over time. For the most recent

list of H3C QSFP+/QSFP28 transceiver modules and

QSFP+/QSFP28 DAC cables available for the card, contact H3C

Support or marketing staff.

For more information about H3C QSFP+/QSFP28 transceiver

modules and QSFP+/QSFP28 DAC cables, see H3C Transceiver

Modules User Guide at www.h3c.com.

LEDs

Table 9 describes QSFP28 port LEDs and QSFP+ port LEDs on the

front panel.

Table 9 QSFP28 port LED description

LED status Description

Steady green

A transceiver module is installed in the port. The

port is operating at 100 Gbps, and a link is present

on the port.

Flashing green The port is sending or receiving data at 100 Gbps.

Steady yellow

A transceiver module is installed in the port. The

port is operating at 10/40 Gbps, and a link is

present on the port.

Flashing yellow

(3 Hz)

The port is sending or receiving data at 10/40

Gbps.

LED status Description

Off No transceiver module is installed in the port, or no

link is present on the port.

Table 10 QSFP+ port LED description

LED status Description

Steady green

A transceiver module is installed in the port. The

port is operating at 40 Gbps, and a link is present

on the port.

Flashing green The port is sending or receiving data at 40 Gbps.

Steady yellow

A transceiver module is installed in the port. The

port is operating at 10 Gbps, and a link is present

on the port.

Flashing yellow The port is sending or receiving data at 10 Gbps.

Off No transceiver module is installed in the port, or

no link is present on the port.

NOTE:

The QSFP28 port LEDs and QSFP+ port LEDs are not affected by

the port LED mode switching button on your switch. For more

information about the port LED mode switching button, see the

installation guide for the switch.

▌Installing and removing the card

CAUTION:

•Before you install or remove the card, wear an ESD wrist strap

and make sure the strap makes good skin contact and is

reliably grounded.

•To avoid device damage, do not use excessive force when you

install or remove the card.

Installing the card

1. Remove the filler panel (if any) from the target slot.

Keep the removed filler panel secure for future use.

2. Unpack the interface card.

Figure 2 LSWM12H2Q interface card

(1) Ejector lever (2) Latch

3. Press the latch on the card to release the ejector lever.

4. As shown by callout 1 in Figure 3, insert the card slowly into the

slot along the guide rails.

5. Rotate inward the ejector lever as shown by callout 2 in Figure 3

until the latch locks the ejector lever in place.

Figure 3 Installing the LSWM12H2Q interface card

Removing the card

CAUTION:

To avoid cable damage, remove the cables from the card before

removing the card.

To remove the card:

1. Prepare an anti-static bag.

2. Press the latch to release the ejector lever

3. Rotate outward the ejector lever as shown by callout 1 in Figure 4.

4. Pull out the interface card slowly out of the interface card slot, as

shown by callout 2 in Figure 4.

5. Place the removed interface card in the anti-static bag.

6. If you are not to install a new card, install a filler panel in the slot to

prevent dust and ensure good ventilation in the device.

Figure 4 Removing the LSWM12H2Q interface card

Installing and removing QSFP28/QSFP+ transceiver

modules and cables

For information about installing and removing QSFP28/QSFP+

transceiver modules and cables, see H3C Transceiver Modules and

Network Cables Installation Guide at www.h3c.com.

Verifying the installation

After the installation is complete, determine whether the card is

operating correctly.

If the card fails to operate correctly, perform the following steps:

1. Reinstall the card following the installation procedures described

in this document.

2. If the problem persists, contact H3C Support.

▌Technical support

New H3C Technologies Co., Ltd. provides customers with

comprehensive technical support and service. If you purchase the

products from the sales agent of New H3C Technologies Co., Ltd.,

please contact our sales agent or technical personnel.

Website: http://www.h3c.com

BOM: 3101A0L1

Table des matières

Autres manuels H3C Matériel réseau

H3C

H3C S9500 Series Manuel utilisateur

H3C

H3C SecCenter CSAP-SA Manuel utilisateur

H3C

H3C ETH682i Manuel utilisateur

H3C

H3C H3C S7500E Series Manuel utilisateur

H3C

H3C SecPathT5030 Manuel utilisateur

H3C

H3C NSQ1GT48EA0 Manuel utilisateur

H3C

H3C SecPath F5000-AI-20 Manuel utilisateur

H3C

H3C H3C S7500E Series Manuel utilisateur

H3C

H3C SecPath U200 Series Manuel utilisateur

H3C

H3C SR8800 IM-FW-II Manuel utilisateur

H3C

H3C WA2620X-AGNP Manuel utilisateur

H3C

H3C MSR Series Manuel d'installation

H3C

H3C LSQM1BFANSCB Manuel utilisateur

H3C

H3C SecPath F50X0 Series Manuel utilisateur

H3C

H3C WA6300-CMW710-R2444P01 Comment utiliser

H3C

H3C DHCP Manuel utilisateur

H3C

H3C SecPath L5030 Manuel utilisateur

H3C

H3C SecPath L1000-A Manuel utilisateur

H3C

H3C FAN-120-1-A Manuel utilisateur

H3C

H3C 1000BASE-X-SFP Manuel utilisateur

H3C

H3C XE 200 Manuel utilisateur

H3C

H3C H3C S7500E-X Guide rapide

H3C

H3C S5120V3-EI Series Manuel utilisateur

H3C

H3C LSWM2ZSP2P Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur