GW Instek GPP-3323 Manuel utilisateur

Programmable DC Power Supply

GPP-1326/GPP-2323/GPP-3323/GPP-4323

User Manual

ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

Table of Contents

SAFETY INSTRUCTIONS .................................................. 6

Safety Symbols...........................................................6

Safety Guidelines ....................................................... 7

Power cord for the United Kingdom ......................... 10

OVERVIEW .................................................................... 11

Introduction............................................................. 12

Key Features ............................................................ 15

Front Panel .............................................................. 17

Rear Panel................................................................ 24

Constant Voltage/Constant Current Crossover

Characteristics ......................................................... 26

GETTING STARTED........................................................ 27

Start Up ................................................................... 28

Load Connection ...................................................... 29

Turning the Output On/Off ...................................... 31

BASIC OPERATION ........................................................ 32

Display Change ........................................................ 33

Source Function ....................................................... 36

Independent Output Mode ..................................... 41

Tracking Series and Tracking Parallel Modes......... 43

Load Function .......................................................... 46

Sequence Function ................................................... 50

Set Sequence Output............................................... 51

Set Group Parameter............................................... 53

Construct Templet................................................... 55

Menu Tree................................................................ 58

Save and Recall ........................................................ 60

GPP Series User Manual

Delay Function ......................................................... 63

Set Delay Output ..................................................... 63

Set Group Parameter............................................... 66

Menu Tree................................................................ 68

Save and Recall ........................................................ 71

Monitor Function ..................................................... 73

Set Monitor.............................................................. 74

Recorder Function.................................................... 76

Set Recorder............................................................. 77

Enternal I/O Control ................................................ 80

Key Function Description ........................................ 82

FILE OPERATION ........................................................... 84

Save/Recall .............................................................. 85

Restore Factory Default Settings .............................. 88

SYSTEM SETTINGS ........................................................ 89

System Information ................................................. 90

System Settings ....................................................... 91

Firmware Upgrading ................................................ 93

Description of Using Flash Drive ............................. 94

REMOTE CONTROL ....................................................... 96

Connection Usage .................................................... 98

RS-232 ...................................................................... 99

USB .......................................................................... 100

GPIB ......................................................................... 102

LAN .......................................................................... 103

Command Syntax ................................................... 109

Command List ....................................................... 113

Measurement Instructions...................................... 113

Display Functions .................................................... 113

Table of Contents

Output Commands ................................................. 113

Source and Load Commands.................................. 114

Status Commands ................................................... 119

System Commands ................................................. 120

System Related Commands .................................... 121

IEEE488.2 Common Commands ............................ 121

Command Details .................................................. 123

Measurement Commands ...................................... 123

Display Commands ................................................. 125

Output Commands ................................................. 127

Source and Load Commands............................... 131

Status Commands ................................................... 174

System Commands ................................................. 180

System Related Commands .................................... 189

SCPI Status Registers SCPI .................................... 190

Event Registers ........................................................ 192

Enable Registers ...................................................... 192

Status Byte Register................................................. 192

Standard Event Register .......................................... 194

Status Byte Register Commands............................. 195

Standard Event Register Commands ...................... 196

Other Status Register Commands .......................... 198

Errors..................................................................... 199

Error Message.......................................................... 199

Command Errors ..................................................... 199

APPENDIX ....................................................................203

Replacing the Fuse ................................................. 203

Specifications ........................................................ 204

Optional Accessories ............................................. 207

Declaration of Conformity ...................................... 208

GPP Series User Manual

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to insure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These symbols may appear in the manual or on the instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the GPP or to other

properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

Do not dispose electronic equipment as

unsorted municipal waste. Please use a

separate collection facility or contact the

supplier from which this instrument was

purchased.

SAFETY INSTRUCTIONS

Safety Guidelines

General

Guideline

CAUTION

Do not place any heavy object on the unit.

Avoid severe impact or rough handling that

leads to damaging the unit.

Do not discharge static electricity to the unit.

Do not block the cooling fan opening.

Do not perform measurements on circuits that

are directly connected to mains power.

Do not disassemble the GPP unless you are

qualified.

(Measurement categories) EN 61010-1:2010

specifies the measurement categories and their

requirements as follows. The GPP Series falls

under category I.

Measurement category IV is for measurement

performed at the source of low-voltage

installation.

Measurement category III is for measurement

performed in the building installation.

Measurement category II is for measurement

performed on the circuits directly connected to

the low voltage installation.

Measurement category I is for measurements

performed on circuits not directly connected to

Mains.

Power Supply

WARNING

AC Input voltage range:

100V/120V/220V/230V ±10%

Frequency: 50Hz/60Hz

To avoid electrical shock connect the protective

grounding conductor of the AC power cord to

an earth ground.

GPP Series User Manual

Fuse

WARNING

Fuse type: 100V/120V：T6.3A/250V，

220V/230V：T3.15A/250V

To prevent fire, replace the fuse only with the

specified type and rating.

Disconnect the power cord before replacing the

fuse.

Make sure the cause of fuse blowout is fixed

before replacing the fuse.

Cleaning the

power supply

Disconnect the power cord before cleaning the

oscilloscope.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid

into the oscilloscope.

Do not use chemicals containing harsh products

such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Relative Humidity: < 80%

Altitude: < 2000m

Temperature: 0° C to 40° C

SAFETY INSTRUCTIONS

(Pollution Degree) EN 61010-1:2010 specifies

pollution degrees and their requirements as

follows. The GPP Series falls under degree 2.

Pollution refers to “addition of foreign matter,

solid, liquid, or gaseous (ionized gases), that

may produce a reduction of dielectric strength

or surface resistivity”.

Pollution degree 1: No pollution or only dry,

non-conductive pollution occurs. The pollution

has no influence.

Pollution degree 2: Normally only non-

conductive pollution occurs. Occasionally,

however, a temporary conductivity caused by

condensation must be expected.

Pollution degree 3: Conductive pollution

occurs, or dry, non-conductive pollution occurs

which becomes conductive due to condensation

which is expected. In such conditions,

equipment is normally protected against

exposure to direct sunlight, precipitation, and

full wind pressure, but neither temperature nor

humidity is controlled.

Storage

environment

Location: Indoor

Relative Humidity: < 70%

Temperature: -10° C to 70° C

GPP Series User Manual

Power cord for the United Kingdom

When using the power supply in the United Kingdom, make sure

the power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed as

follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the

terminal marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or

contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable

of 0.75mm2should be protected by a 3A or 5A fuse. Larger

conductors would normally require 13A types, depending on the

connection method used.

Any exposed wiring from a cable, plug or connection that is

engaged in a live socket is extremely hazardous. If a cable or plug is

deemed hazardous, turn off the mains power and remove the cable,

any fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GW Instek Alimentation

GW Instek

GW Instek PSB-2000 series Manuel utilisateur

GW Instek

GW Instek PFR-100 Series Mode d'emploi

GW Instek

GW Instek GPD-2303S Manuel utilisateur

GW Instek

GW Instek PEL-3021 Manuel utilisateur

GW Instek

GW Instek GPP-3060 Manuel utilisateur

GW Instek

GW Instek PSP-603 Manuel utilisateur

GW Instek

GW Instek PRP Series Manuel du propriétaire

GW Instek

GW Instek PSW 30-72 Manuel du propriétaire

GW Instek

GW Instek PHX 60-100 Manuel utilisateur

GW Instek

GW Instek PSW Series Manuel utilisateur

GW Instek

GW Instek PSH series Manuel utilisateur

GW Instek

GW Instek PSW Series Manuel utilisateur

GW Instek

GW Instek PSU Series Manuel du propriétaire

GW Instek

GW Instek PSU Series Manuel utilisateur

GW Instek

GW Instek ASR-2000 Series Manuel utilisateur

GW Instek

GW Instek PEL-3000A Series Manuel utilisateur

GW Instek

GW Instek PSS-3203 Manuel utilisateur

GW Instek

GW Instek PSW 30-36 Manuel utilisateur

GW Instek

GW Instek SPD-3606 Manuel utilisateur

GW Instek

GW Instek PPH-1503D Manuel utilisateur

GW Instek

GW Instek PSU Series Manuel utilisateur

GW Instek

GW Instek PSB-1400L Manuel utilisateur

GW Instek

GW Instek PSP-603 Manuel utilisateur

GW Instek

GW Instek GPP-3650 Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur