GW Instek GPP-3060 Manuel utilisateur

Programmable DC Power Supply

GPP-3060/GPP-6030

User Manual

ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

SAFETY INSTRUCTIONS

Table of Contents

SAFETY INSTRUCTIONS .................................................. 7

Safety Symbols...........................................................7

Safety Guidelines ....................................................... 8

Power cord for the United Kingdom ......................... 11

OVERVIEW .................................................................... 12

Introduction............................................................. 13

Key Features ............................................................ 16

Front Panel .............................................................. 18

Rear Panel................................................................ 24

Constant Voltage/Constant Current Crossover

Characteristics ......................................................... 26

GETTING STARTED........................................................ 27

Start Up ................................................................... 28

Load Connection ...................................................... 29

Select front/rear panel output.................................. 31

Turning the Output On/Off ...................................... 32

BASIC OPERATION ........................................................ 33

Display Change ........................................................ 34

Source Function ....................................................... 37

Independent Output Mode ..................................... 43

Tracking Series and Tracking Parallel Modes......... 45

Load Function .......................................................... 50

Sequence Function ................................................... 54

Set Sequence Output............................................... 54

Set Group Parameter............................................... 57

Construct Templet................................................... 58

Menu Tree................................................................ 61

GPP-3060/6030 User Manual

Save and Recall ........................................................ 63

Delay Function ......................................................... 66

Set Delay Output ..................................................... 66

Set Group Parameter............................................... 69

Menu Tree................................................................ 72

Save and Recall ........................................................ 74

Monitor Function ..................................................... 77

Set Monitor.............................................................. 77

Recorder Function.................................................... 81

Set Recorder............................................................. 81

External I/O Control................................................. 85

Key Function Description ........................................ 87

FILE OPERATION ........................................................... 89

Save/Recall .............................................................. 90

Restore Factory Default Settings .............................. 93

SYSTEM SETTINGS ........................................................ 94

System Information ................................................. 95

System Settings ....................................................... 96

Firmware Upgrading ................................................ 98

Description of Using Flash Drive ............................. 99

REMOTE CONTROL ......................................................101

Connection Usage .................................................. 103

RS-232 ...................................................................... 104

USB .......................................................................... 106

GPIB ......................................................................... 108

LAN .......................................................................... 110

Command Syntax ................................................... 116

Command List ....................................................... 120

Measurement Instructions...................................... 120

SAFETY INSTRUCTIONS

Display Functions .................................................... 120

Output Commands ................................................. 120

Source and Load Commands.................................. 121

Status Commands ................................................... 126

System Commands ................................................. 127

System Related Commands .................................... 128

IEEE488.2 Common Commands ............................ 129

Command Details .................................................. 130

Measurement Commands ...................................... 130

Display Commands ................................................. 132

Output Commands ................................................. 134

Source and Load Commands.................................. 139

Status Commands ................................................... 183

System Commands ................................................. 190

System Related Commands .................................... 199

SCPI Status Registers SCPI .................................... 200

Event Registers ........................................................ 202

Enable Registers ...................................................... 202

Status Byte Register................................................. 202

Standard Event Register .......................................... 204

Status Byte Register Commands............................. 205

Standard Event Register Commands ...................... 206

Other Status Register Commands .......................... 208

Errors..................................................................... 209

Error Message.......................................................... 209

Command Errors ..................................................... 209

APPENDIX ....................................................................213

Replacing the Fuse ................................................. 213

Specifications ........................................................ 214

Optional Accessories ............................................. 217

GPP-3060/6030 User Manual

Declaration of Conformity ...................................... 218

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to insure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These symbols may appear in the manual or on the instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the GPP or to other

properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

Do not dispose electronic equipment as

unsorted municipal waste. Please use a

separate collection facility or contact the

supplier from which this instrument was

purchased.

GPP-3060/6030 User Manual

Safety Guidelines

General

Guideline

CAUTION

Do not place any heavy object on the unit.

Avoid severe impact or rough handling that

leads to damaging the unit.

Do not discharge static electricity to the unit.

Do not block the cooling fan opening.

Do not perform measurements on circuits that

are directly connected to mains power.

Do not disassemble the GPP unless you are

qualified.

(Measurement categories) EN 61010-1:2010

specifies the measurement categories and their

requirements as follows. The GPP Series falls

under category I .

․Measurement category IV is for measurement

performed at the source of low-voltage

installation .

․Measurement category III is for measurement

performed in the building installation.

․Measurement category II is for measurement

performed on the circuits directly connected to

the low voltage installation.

․Measurement category I is for measurements

performed on circuits not directly connected to

Mains.

SAFETY INSTRUCTIONS

(Pollution Degree) EN 61010-1:2010 specifies

pollution degrees and their requirements as

follows.Pollution refers to “addition of foreign

matter, solid, liquid, or gaseous (ionized gases),

that may produce a reduction of dielectric

strength or surface resistivity”. The GPP Series

falls under degree 2.

․Pollution degree 1: No pollution or only dry, non-

conductive pollution occurs. The pollution has no

influence.

․Pollution degree 2: Normally only non-conductive

pollution occurs. Occasionally, however, a

temporary conductivity caused by condensation

must be expected.

․Pollution degree 3: Conductive pollution occurs, or

dry, non-conductive pollution occurs which

becomes conductive due to condensation which is

expected. In such conditions, equipment is

normally protected against exposure to direct

sunlight, precipitation, and full wind pressure, but

neither temperature nor humidity is controlled.

Power Supply

WARNING

AC Input voltage range:

100V/120V/220V/230V ±10%

Frequency: 50Hz/60Hz

To avoid electrical shock connect the protective

grounding conductor of the AC power cord to

an earth ground.

Fuse

WARNING

Fuse type: 100V/120V：T12A/250V，

220V/230V：T5A/250V

To prevent fire, replace the fuse only with the

specified type and rating.

Disconnect the power cord before replacing the

fuse.

Make sure the cause of fuse blowout is fixed

before replacing the fuse.

GPP-3060/6030 User Manual

Cleaning the

power supply

Disconnect the power cord before cleaningit .

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid

into it.

Do not use chemicals containing harsh products

such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Relative Humidity: < 80%

Altitude: < 2000m

Temperature: 0°C to 40°C

Storage

environment

Location: Indoor

Relative Humidity: < 70%

Temperature: -10°C to 70°C

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GW Instek Alimentation

GW Instek

GW Instek PRP Series Manuel du propriétaire

GW Instek

GW Instek PSH series Manuel utilisateur

GW Instek

GW Instek GPP-1326 Manuel utilisateur

GW Instek

GW Instek ASR-2000 Series Manuel utilisateur

GW Instek

GW Instek PFR-100 Series Mode d'emploi

GW Instek

GW Instek PSW Series Manuel du propriétaire

GW Instek

GW Instek PSU Series Manuel du propriétaire

GW Instek

GW Instek GPP-2323 Manuel utilisateur

GW Instek

GW Instek PSB-1400M Manuel utilisateur

GW Instek

GW Instek PEL-3000A Series Manuel utilisateur

GW Instek

GW Instek GPE-1326 Series Manuel utilisateur

GW Instek

GW Instek PPH-1503D Manuel utilisateur

GW Instek

GW Instek PSP-603 Manuel utilisateur

GW Instek

GW Instek PSW Series Manuel utilisateur

GW Instek

GW Instek PSU Series Manuel du propriétaire

GW Instek

GW Instek PEL-500 Series Manuel utilisateur

GW Instek

GW Instek SPS-1230 Manuel utilisateur

GW Instek

GW Instek GCP-206P Manuel utilisateur

GW Instek

GW Instek PSW Series Manuel utilisateur

GW Instek

GW Instek PPX Series Manuel utilisateur

GW Instek

GW Instek GPE-1326 Series Manuel utilisateur

GW Instek

GW Instek PFR-100MGP Manuel utilisateur

GW Instek

GW Instek PSB-2000 series Manuel utilisateur

GW Instek

GW Instek PSW Series Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur