GW Instek GPM-8320 Manuel utilisateur

Digital Power Meter

GPM-8320/8330

USER MANUAL

Rev. A

ISO-9001 CERTIFIED MANUFACTURER

Ihr Ansprechpartner /

Your Partner:

dataTec AG

E-Mail: [email protected]

>>> www.datatec.eu

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

TABLE OF CONTENTS

Table of Contents

SAFETY INSTRUCTIONS .................................................. 5

GETTING STARTED........................................................ 10

Characteristics......................................................... 11

Appearance.............................................................. 15

Set Up ..................................................................... 25

BASIC SETTING ............................................................. 27

Setting up measurement range ................................ 29

Setting up measurement status ............................... 33

Setting up System status ......................................... 70

MEASUREMENT AND OTHER FUNCTIONS .................... 80

Measurement function ............................................ 81

Other functions ....................................................... 94

Integration measurement function .......................... 97

Graph measurement function ................................ 107

DIGITAL I/O / DA12......................................................125

Digital I/O / DA12 Overview.................................. 126

External Remote Control ........................................ 128

DA12 Output Function........................................... 129

REMOTE CONTROL ......................................................134

Configure Remote Control Interface....................... 135

Configure EOL Character ....................................... 142

Return to Local Control ......................................... 142

COMMAND OVERVIEW ................................................143

Command Syntax ................................................... 143

Command List ....................................................... 147

GPM-8320/8330 User Manual

APPENDIX ....................................................................228

Specifications ........................................................ 229

Status system ........................................................ 239

Dimensions ........................................................... 243

Certificate Of Compliance ...................................... 244

Power measurement .............................................. 245

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to ensure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the

instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the GPM-8320/8330

or to other properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

GPM-8320/8330 User Manual

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

SAFETY INSTRUCTIONS

Safety Guidelines

General Guideline

CAUTION

 Make sure that the voltage input level does not

exceed AC600V.

 Make sure the current input level does not

exceed 20A.

 Do not place any heavy object on the

instrument.

 Avoid severe impact or rough handling that can

lead to damaging the instrument.

 Do not discharge static electricity to the

instrument.

 Use only mating connectors, not bare wires, for

the terminals.

 Do not block or obstruct the cooling fan vent

opening.

 Do not perform measurement at the source of a

low-voltage installation or at building

installations (Note below).

 Do not disassemble the instrument unless you

are qualified as service personnel.

 Make sure that the COM terminal to earth is

limited to 600Vpk.

 Remove all test leads before disconnecting the

mains power cord from the socket.

 If the equipment is used in a manner not

specified by the manufacturer, the protection

provided by the equipment may be impaired.

 The device should be placed in a place where

the plug connected to it can be removed easily.

 Interface: USB / RS232 / LAN2/ Mini GPIB

/Digital IO DA12 ports are only to be connected

to the circuits which are separated from mains

supply by double / reinforce insulation.

GPM-8320/8330 User Manual

(Note) EN 61010-1:2010 specifies the measurement categories and

their requirements as follows. The GPM-8320/8330 falls under

category II 600V.

Measurement category IV is for measurement performed at the

source of low-voltage installation.

Measurement category III is for measurement performed in the

building installation.

Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

Power Supply

WARNING

AC Input voltage: 100-240 VAC 50/60Hz

The power supply voltage should not fluctuate

more than 10%.

Connect the protective grounding conductor of

the AC power cord to an earth ground, to avoid

electrical shock.

Cleaning the

Instrument

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals containing harsh material

such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Temperature: 0°C to 40°C

Humidity: < 30°C: < 80%RH(non-condensing);

30°C~40°C:<70%RH(non-condensing);

>40°C: <50%RH (non-condensing)

Altitude: <2000m

Overvoltage category: OVC II

SAFETY INSTRUCTIONS

(Note) EN 61010-1:2010 specifies the pollution degrees and their

requirements as follows. The GPM-8320/8330 falls under degree 2.

 Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of

dielectric strength or surface resistivity”.

 Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

 Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

 Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

Storage

environment

 Location: Indoor

 Temperature: -40°C to 70°C

 Humidity: <90%RH(non-condensing)

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

GPM-8320/8330 User Manual

GETTING STARTED

This chapter describes the GPM-8320/8330 in a

nutshell, including accessories, package contents,

its main features and front / rear panel

introduction.

Characteristics ......................................................... 11

Accessories.......................................................................... 13

Package Contents................................................................ 14

Appearance.............................................................. 15

Front Panel..........................................................................15

GPM-8320/8330.......................................................15

Main Display Overview ....................................................... 18

Rear Panel ........................................................................... 21

GPM-8330 ................................................................21

GPM-8320 ................................................................21

GPM-8330 (without GPIB +DA 12 interface)..........22

Set Up ..................................................................... 25

Power Up............................................................................. 25

Connect the wires to the GPM-8320/8330......................... 26

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GW Instek Instrument de mesure

GW Instek

GW Instek GOM-804 Manuel utilisateur

GW Instek

GW Instek LCR-800 Series Manuel utilisateur

GW Instek

GW Instek LCR-8230 Manuel d'utilisation et d'entretien

GW Instek

GW Instek GOM-802 Manuel utilisateur

GW Instek

GW Instek GOM-802 Manuel utilisateur

GW Instek

GW Instek GDM-906 Series Manuel utilisateur

GW Instek

GW Instek 82PM-82120MB Manuel utilisateur

GW Instek

GW Instek GOM-802 Manuel utilisateur

GW Instek

GW Instek LCR-8230 Manuel utilisateur

GW Instek

GW Instek GDS-1000B Series Manuel utilisateur

GW Instek

GW Instek GFC-8131H Manuel utilisateur

GW Instek

GW Instek LCR Series Manuel utilisateur

GW Instek

GW Instek GPM-001 Manuel utilisateur

GW Instek

GW Instek GSP-9300 Manuel utilisateur

GW Instek

GW Instek GLP-1A Manuel utilisateur

GW Instek

GW Instek GSP-818 Series Manuel utilisateur

GW Instek

GW Instek GSP-8000 Series Manuel utilisateur

GW Instek

GW Instek GLA-1016 Manuel utilisateur

GW Instek

GW Instek GSP-9300B Manuel utilisateur

GW Instek

GW Instek GSP-9300 Manuel utilisateur

GW Instek

GW Instek LCR-8101G Manuel utilisateur

GW Instek

GW Instek GPM-8310 Manuel utilisateur

GW Instek

GW Instek PEL-5000G Series Manuel utilisateur

GW Instek

GW Instek GLA-1016 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur