GW Instek AFG-3000 Series Manuel utilisateur

RF &Communication Trainer

GRF-1300A

STUDENT BOOK

USER MANUAL and TEXT BOOK

GW INSTEK PART NO. 82RF-1300AM01

ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by copyright. All rights are reserved.

No part of this manual may be photocopied, reproduced or translated to another language without

prior written consent of Good Will Corporation.

The information in this manual was correct at the time of printing. However, Good Will continues to

improve its products and therefore reserves the right to change the specifications, equipment, and

maintenance procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

Table of Contents

SAFETY INSTRUCTIONS ................................................................ 2

ABOUT THIS BOOK ....................................................................... 5

INTRODUCTION to the GRF-1300A ............................................... 6

Package Contents .................................................................................................... 8

Product Specifications and Function........................................................................ 8

Usage Instructions .................................................................................................. 9

OVERVIEW of the TIME and FREQUENCY DOMAIN.................... 16

Observation from a different perspective................................................................16

AN INTRODUCTION to SPECTRUM ANALYZERS ........................ 24

Broadband Receiver ................................................................................................24

Attenuator ..............................................................................................................25

Resolution Bandwidth Filter....................................................................................25

Detector .................................................................................................................27

Video Bandwidth Filter ...........................................................................................27

RF COMMUNICATION and SIGNALS EXPERIMENTS .................. 31

Experiment 1: Basic Operation of a Spectrum Analyzer...........................................32

Experiment 2: Measuring a Baseband Waveform.....................................................36

Experiment 3: Different Baseband Waveforms and their Harmonic Measurement...40

Experiment 4: Measurement of the RF Carrier.........................................................47

Experiment 5: AM Signal Measurement ..................................................................60

Experiment 6: FM signal measurement ...................................................................70

Experiment 7: Using a Spectrum Analyzer in Communication Systems ...................81

Experiment 8: Measurement of communication products .......................................88

Experiment 9: Production Line Applications ...........................................................91

Experiment 10: Mixer ..............................................................................................96

TEST for LEARNING OUTCOMES .............................................. 108

APPENDIX.................................................................................. 117

dBm Conversion Table ..........................................................................................117

The relationship between dB and dBc ...................................................................118

Resistor Values in π-type Resistance Attenuators..................................................119

Resistor Values in T-type Resistance Attenuators..................................................120

Modulation Index and Sideband Amplitude Comparison Table .............................121

Declaration of Conformity.....................................................................................122

GRF-1300A User Manual and Teaching Materials

SAFETY INSTRUCTIONS

This chapter contains important safety instructions that

should be followed when operating and storing the GRF-1300A.

Read the following before any operation to ensure your safety

and to keep the GRF-1300A in the best condition.

Safety Symbols

These safety symbols may appear in this manual or on the instrument.

WARNING Warning: Identifies conditions or practices that could result in injury

or loss of life.

CAUTION Caution: Identifies conditions or practices that could result in

damage to the GRF-1300A or to other objects or property.

DANGER High Voltage

Attention: Refer to the Manual

Protective Conductor Terminal

Earth (Ground) Terminal

Do not dispose electronic equipment as unsorted municipal waste.

Please use a separate collection facility or contact the supplier from

which this instrument was purchased.

Safety Guidelines

General

Guideline

CAUTION

•Do not place heavy objects on the device.

•Do not place flammable objects on the device.

•Avoid severe impact or rough handling that may damage the

device.

•Avoid discharges of static electricity on or near the device.

•Use only mating connectors, not bare wires, for the terminals.

•The device should only be disassembled by a qualified technician.

Safety Instructions

(Measurement categories) EN 61010-1:2010 specifies the measurement categories and

their requirements as follows. The device falls under category I.

•Measurement category IV is for measurement performed at the source of a low-voltage

installation.

•Measurement category III is for measurement performed in a building installation.

•Measurement category II is for measurement performed on circuits directly connected

to a low voltage installation.

•Measurement category I is for measurements performed on circuits not directly

connected to Mains.

Power Supply

WARNING

•AC Input voltage: 100 ~ 240V AC, 50 ~ 60Hz.

•Connect the protective grounding conductor of the AC power cord

to an earth ground to prevent electric shock.

Fuse

WARNING

•Fuse type: 1A/250V.

•Only qualified technicians should replace the fuse.

•To ensure fire protection, replace the fuse only with the specified

type and rating.

•Disconnect the power cord and all test leads before replacing the

fuse.

•Make sure the cause of the fuse blowout is fixed before replacing

the fuse.

Cleaning the

GRF-1300A

•Disconnect the power cord before cleaning the device.

•Use a soft cloth dampened in a solution of mild detergent and

water. Do not spray any liquid into the device.

•Do not use chemicals containing harsh products such as benzene,

toluene, xylene, and acetone.

Operation

environment

•Location: Indoor, no direct sunlight, dust free, almost non-

conductive pollution (Note below) and avoid strong magnetic

fields.

•Relative Humidity: < 80%

•Altitude: < 2000m

•Temperature: 0°C to 40°C

(Pollution Degree) EN 61010-1:2010 specifies pollution degrees and their requirements as

follows. The device falls under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or gaseous (ionized gases),

that may produce a reduction of dielectric strength or surface resistivity”.

•Pollution degree 1: No pollution or only dry, non-conductive pollution occurs. The

pollution has no influence.

•Pollution degree 2: Normally only non-conductive pollution occurs. Occasionally,

however, a temporary conductivity caused by condensation must be expected.

•Pollution degree 3: Conductive pollution occurs, or dry, non-conductive pollution

occurs which becomes conductive due to condensation which is expected. In such

conditions, equipment is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature nor humidity is

controlled.

Storage

environment

•Location: Indoor

•Relative Humidity: < 70%

•Temperature: -10°C to 70°C

GRF-1300A User Manual and Teaching Materials

Disposal

Do not dispose this device as unsorted municipal waste. Please use a

separate collection facility or contact the supplier from which this

instrument was purchased. Please make sure discarded electrical

waste is properly recycled to reduce environmental impact.

Power cord for the United Kingdom

When using the device in the United Kingdom, make sure the power cord meets the following safety

instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the following code:

Green/ Yellow: Earth

Blue: Neutral

Brown: Live (Phase)

As the colours of the wires in main leads may not correspond with the coloured marking identified in

your plug/appliance, proceed as follows:

The wire which is coloured Green & Yellow must be connected to the Earth terminal marked with either

the letter E, the earth symbol or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or

coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal marked with the letter L or P or

coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or contact the supplier.

This cable/appliance should be protected by a suitably rated and approved HBC mains fuse: refer to the

rating information on the equipment and/or user instructions for details. As a guide, a cable of 0.75mm2

should be protected by a 3A or 5A fuse. Larger conductors would normally require 13A types,

depending on the connection method used.

Any exposed wiring from a cable, plug or connection that is engaged in a live socket is extremely

hazardous. If a cable or plug is deemed hazardous, turn off the mains power and remove the cable, any

fuses and fuse assemblies. All hazardous wiring must be immediately destroyed and replaced in

accordance to the above standard.

Introduction to the GRF-1300A

ABOUT THIS BOOK

This textbook was developed in conjunction with the GRF-

1300A RF & Communication Trainer and the GSP-730 3GHz

spectrum analyzer as an RF communications education system.

It not only offers detailed examples, but also the practical

knowledge necessary for RF measurements, such as spectrum

analyzer principals, as well as AM and FM communication

systems.

For you to easily understand the contents of this textbook,

we have included as many pictures and diagrams as possible to

strengthen your comprehension.

This book is divided into a teacher version and two student

versions. All experiment results are included in the teacher

edition. In addition, chapters with an asterisk (*) indicate

additional text for advanced reading not present in the student

addition. Students will not be affected by the omission of the

additional text. To further help students, the student edition

will contain a “Notes” section in these missing areas.

GRF-1300A User Manual and Teaching Materials

INTRODUCTION to the GRF-1300A

The GRF-1300A is a well designed training kit capable of

producing a 3MHz baseband signal and a carrier signal up to

900MHz. The GRF-1300A is also able to perform AM and FM

RF circuit experiments as well. The practical exercises in the

training kit meet the needs of most general RF courses. The

GRF-1300A consists of three modules, namely: a baseband

module, an RF Synthesizer/FM module and an AM module.

The baseband module can simulate a baseband signal and

includes sine, square or triangle waveforms. Its output

frequency and amplitude are adjustable. During experiments

the three kinds of waveforms can be arbitrarily switched back

and forth to meet the signaling requirements of each of the

different experiments.

The RF Synthesizer/FM module is used to generate an

adjustable carrier frequency as well as perform frequency

modulation. This module covers some of the focus points in the

RF circuit theory. This will be highlighted in practical

experiments in later chapters. FM waveforms can also be

produced by using this module together with the baseband

module. The GSP-730 spectrum analyzer can be used to observe

the various characteristics of an FM waveform.

The AM module and baseband module can be used

together to perform amplitude modulation experiments. The

GSP-730 Spectrum Analyzer can be used to observe the various

characteristics of an AM waveform.

The mixer can convert the RF signal into an intermediate

frequency signal or it can do the opposite and convert the

intermediate frequency signal into an RF frequency signal in

order to transmit or process the carried message, respectively.

This experiment system can be connected to a computer via

the USB interface. The interface can be used to turn individual

circuits on or off so that students can perform diagnostic

experiments.

Students can learn the fundamental aspects of RF theory

through a variety of experiments. Understanding RF theory has

been made easier by breaking the RF circuits into fundamental

Introduction to the GRF-1300A

functions. This allows students to see in detail how the theory

relates to the practical aspects of the RF circuitry.

This system is a collection of different functions: signal

generation, frequency modulation, amplitude modulation,

communication and other functions. Connecting different

modules together can create a number of different RF circuit

experiments. Specific experiments will be highlighted in later

chapters. The GRF-1300A RF & Communication Trainer is

designed to modulate an audio signal with a carrier waveform.

The system takes into account the difficulties arising from RF

circuit theory and knowledge. It focuses on these theories and

sets up experiments to understand the theoretical aspects of RF

circuitry – This also has the added benefit of increasing a

student’s interest to learn RF circuits.

Figure A-1.

The GRF-1300A

control panel

Figure A-2.

Reference

platform: GSP-

730 Spectrum

Analyzer

GRF-1300A User Manual and Teaching Materials

Package Contents

This package contains the GRF-1300A unit, RF cable – 3 *

10cm, 1*20cm,RF cable 2* 80cm, a user manual CD, a student

book, an antenna, a power cord and so on.

Title Photo No Note

GRF-1300A

RF wire 3 100mm

RF wire 1 200mm

RF wire

2 800mm

Antenna 2 800-1000MHz

AC power cord 1 100-240V～50-60Hz

1 User manual and

software

Adapter

1 N-SMA Adapter

Student

Textbook

1 RF & Communication

Trainer

Product Specifications and Function

Function Item Spec.

Waveforms Sine, Square, Triangle

Frequency Range

0.1~3MHz

(Triangle-0.1~1MHz)

Step: 10kHz

Amplitude ≥1.5Vpp

≥0.75Vpp into 50Ω

Base Band

Harmonics Distortion ≤-30dBc

Frequency Accuracy ±0.15MHz

Adjustable Range ≥45MHz (870M~920M)

Step: 1MHz

RF/FM Analysis

Power Range ≥-15dBm

FM Max Frequency

Deviation >3MHz

AM Peak Difference ≥-18dBm

Mixer LO+IF≥-35dBm

Autres manuels pour AFG-3000 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GW Instek Instrument de mesure

GW Instek

GW Instek GFG-8215A Manuel utilisateur

GW Instek

GW Instek GCM-407 Manuel utilisateur

GW Instek

GW Instek GSP-810 Manuel utilisateur

GW Instek

GW Instek GOM-802 Manuel utilisateur

GW Instek

GW Instek GPM-001 Manuel utilisateur

GW Instek

GW Instek GSP-9300 Manuel utilisateur

GW Instek

GW Instek GDM-906 Series Manuel utilisateur

GW Instek

GW Instek GFC-8131H Manuel utilisateur

GW Instek

GW Instek GSM-20H10 Manuel utilisateur

GW Instek

GW Instek GLA-1016 Manuel utilisateur

GW Instek

GW Instek GSP-730 Manuel utilisateur

GW Instek

GW Instek GRF-1300 Manuel utilisateur

GW Instek

GW Instek PEL-3111H Manuel utilisateur

GW Instek

GW Instek PEL-5000G Series Manuel utilisateur

GW Instek

GW Instek LCR-817 Manuel utilisateur

GW Instek

GW Instek GSP-830 Manuel utilisateur

GW Instek

GW Instek GSP-9300B Manuel du propriétaire

GW Instek

GW Instek LCR-8101G Manuel utilisateur

GW Instek

GW Instek GSP-8000 Series Manuel du propriétaire

GW Instek

GW Instek GSP-9300 Manuel utilisateur

GW Instek

GW Instek GOM-802 Manuel utilisateur

GW Instek

GW Instek GDM-8342 Manuel utilisateur

GW Instek

GW Instek GPT-10000 Series Manuel utilisateur

GW Instek

GW Instek GPM-8213 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur