Guru EVOLUX Manuel utilisateur
PRODUCT GUIDE
EVOLUX SYSTEM
LINEAR/SQUARE DRAINAGE
2
CONTENT
DESCRIPTION 4
• CHARACTERISTICS AND COMPONENTS 4
»Technical, aesthetic and practical evolution 4
»Waterproofing 5
»Drain 5
»Drainage 6
»Accessories for installation and maintenance 6
NEW FORMATS 7
• MORE SHOWER CONFIGURATION OPTIONS 7
INSTALLATION EVOLUX SYSTEM 8
• GENERAL INSTALATION PROCEDURE FOR THE EVOLUX SYSTEM 8
• INSTALLATION WITH TEMPLATE 11
• INSTALLATION WITH INTEGRA SYSTEM 12
• INSTALLATION DIAGRAM 13
RECOMENDATIONS 15
PRODUCT DATA SHEET 16
WARRANTY 17
3
4
It comprises a section of WATER-STOP waterproofing membrane, factory-sealed to
a special adapter to connect to a low profile floor gully and a stainless steel shower
drain and grill.
• TECHNICAL, AESTHETIC AND PRACTICAL EVOLUTION
Separate installation of the drain body and the waterproof membrane, which is easier and
more practical.
Push fit, flexible connections with elastic uncoupling: no gluing needed
The floor gully is easy to adjust and align with the flooring because of the flexibility of the
connections
Minimum installation height of 90 mm including the flooring of 9 mm total thickness with
adhesive.
Dripping holes for secondary drainage with backflow preventer system
The water seal can be eliminated.
Accepts large-format floor coverings with 1 or 2 slopes to the linear drainage.
Different grill installation positions possible.
• Sideways, away from the wall.
• Traditional central installation with 4-way slope.
• Completely flush to the wall with 1 or 3 slopes (with the PERFIL LATERAL
optional accessory).
DESCRIPTION
5
• WATERPROOFING
In the EVOLUX system LINEAR KIT;
2 x 2 m (4 m²) WATER-STOP membrane with the connector in lateral position centred
widthways and 25 cm from the edge.
In the EVOLUX BASE set (depending on model);
BASE 3: 1.5 x 2 m (3 m²) WATER-STOP membrane with the connector centred at
widthways and at 2/3 lengthways (66 cm from the nearest end).
BASE 4: 2 x 2 m (4 m²) WATER-STOP membrane with the connector in lateral position
centred widthways and 25 cm from the edge.
• DRAIN
The EVOLUX BASE set doesn’t include drain extension and cover. It must be
completed with the EVOLUX shower drain and grill, which can be chosen among
the different models available.
Drain bodies and grills of AISI 304 stainless steel 1.5 mm thick. Measures and designs
depending on model.
» Linear drains 69 mm width with internal slopes and 53 mm wide grid defining a
slot of 6 mm oneach side for water drainage. Available in 6 sizes: 60 / 70 / 80 / 90
/ 100 and 120 cm long.
» A traditional square shape for central draining with 4-way slope. The exterior
dimensions of thedrain tray are 11.6 x 11.6 cm, with internal slopes and a 10 x 10
cm grill defining a 6 mm-wideperimeter drainage slot. The INTEGRA model accepts
a standard 10 x 10 tile insert.
» A smart, modern rectangular shape for central draining with 4-way slope or for
an unconventional3-way slope when installed flush to the wall using the PERFIL
LATERAL accessory. The exteriordimensions of the drain tray are 15 x 30 cm, with
internal slopes and a 13.4 x 28.4 cm grill defining a 6 mm-wide perimeter drainage
slot.
5 models of shower grating designs available:
DESCRIPTION
• LISA - With satin finish and plain design.
• PLUS - With satin finish and laser-cut
patterned.
• LISA DARK - with black finish plain
design.
• PLUS DARK - with satin finish and laser-
cut patterned.
• MICRO-CEMENT with microcement
finish design.
• TEMPERED GLASS - with tempered
glass finish design.
• INTEGRA - With a section designed
to accept a piece of the same material
as the surroundingflooring and comes
with special accessories that with a few
simple steps in the installation, makeit a
hidden drain.
• PRINTED - with costumized design
include it in the grid.
6
• DRAINAGE
Low profile trapped floor gully which complies to EN 1253, parts 1 and 2
Side outlet with DN/OD 50 connector. It can be angled through 360º
50 mm-high water seal (can be eliminated).
Reducer: DN 50/40
Push fit connections with O-rings and sliding joints; not gluing.
Drain body and connector: ABS ; Reducer: PP; Joints: EPDM
Flow rate from 0.4 l/s to 0.65 l/s depending on model.
• ACCESSORIES FOR INSTALLATION AND MAINTENANCE
Installation cap to protect the drain and mark the suitable screed level.
Template to use when installing with a very low flooring pavement or the INTEGRA
system.
2 sealing reinforcement for interior corners W-S DIN.
2 sealing reinforcement for shower inlet pipes W-S TUBO.
Hair trap.
DESCRIPTION
7
WITH BASE 3 m2WITH BASE 4 m2
1,2 m
0,9 m
1,4 m
1,2 m
1,2 m
0,9 m
1,6 m
1,2 m
1 m
1,75 m
1,8 m
0,9 m
2 m
2 m
2 m
1,5 m
NEW FORMATS
• MORE SHOWER CONFIGURATION OPTIONS
8
Prepare the shower area
•Decide on the height or depth required to ensure at least 1.5 % gradient towards the
drain. At the drain point, a minimum base thickness of 110 mm is required (including
3 to 25 mm tile thickness with adhesive). Install the siphon body
Warning: Before starting the installation it is very important to check if you need
a trapped drain.
The system main body is designed as a trapped drain but the water seal can
be left out to avoid the risk of clogging for double-trapping when installed
with an external drum trap: just remove the tubular piece (1) and then open
the bottom part of the outlet pipe (2). This is a section made with breaking line
that can be easily broken using a screwdriver or similar (3).
1 2 3
You cannot remove the water seal after the installation nor replace it. It is advisable to keep
the drain trapped and connect directly to the waste pipe without going through an external
trap.
•Install the floor gully body and position the outlet to allow connection to the waste
pipe.
•Check that the outlet has the necessary gradient (minimum 1.5 %) towards the waste
pipe.
•Connect the floor gully outlet to the drain pipe. If needed use the reducer 50/40
supplied. Lubricate the joint with soapy water, introduce the drain pipe and slide up
to the limit.
INSTALLATION
• GENERAL INSTALLATION PROCEDURE FOR THE EVOLUX SYSTEM
9
4. Cut to size (remember to leave 10 cm on
each side to seal wall and floor joints).
5. Connect the membrane by introducing
the adapter into the floor gully and press
down until it pushes home.
6. Fix the membrane with C2 tile adhesive
to the cement base which must be clean
and dry and shower drain.
2. Pour cement screed up to the level
indicated on the protective cap.*
3. Once the cement base has set remove
the protective cap, unroll and position the
WATER-STOP membrane
1
2
3
4
5
6
*To make up for the height when installing a very thin flooring as mosaic glass tiles,
microcement or other (less than 7 mm total flooring depth) and for installing EVOLUX
INTEGRA System, you must use the TEMPLATE provided. To do this, follow the instructions
in the relevant sections later.
INSTALLATION
Make up the cement screed base
1. Cover the floor gully mouth with the cap
supplied.
10
Position the shower drain
• If necessary, prepare the drain by assembling the PERFIL LATERAL accessory.
• Lay a piece of the flooring to set a reference height for the installation.
• Lubricate the shower drain outlet with soapy water and slide into the connector.
•Apply a small amount of C2 class tile adhesive to each side to help seat the shower
channel andpress together.
•Level, align and adjust the height according to floor thickness so that the upper edge
is flush tothe flooring.
Position the flooring
• Cement directly to the WATER-STOP membrane using C2 tile adhesive.
•Seal the joint between the flooring and the shower channel edge with W-S MASTIC or
similar and position the grill.
INSTALLATION
Reducer 50/40
1.5% mín.
1.5% mín.
C2 class tile adhesive
Flooring
W-S MASTIC
Adapter
Trapped body with water seal
WATER -STOP membrane
Slab
50 mm
Waste pipe
78 mm
90 mm
Sloped cement screed
Shower channel
and grill
EVOLUX System installation example with 9 mm flooring thickness
• EVOLUX INSTALLATION DIAGRAM
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Guru Appareil de salle de bains
