Grundfos TPE 2 Series Manuel utilisateur

TPE2 (D), TPE3 (D)

Installation and operating instructions

GRUNDFOS INSTRUCTIONS

Other languages

http://net.grundfos.com/qr/i/98450210

English (GB)

English (GB) Installation and operating instructions

Original installation and operating instructions

CONTENTS

Page

1. Symbols used in this document 3

2. Abbreviations and definitions 4

3. General information 4

4. General description 4

4.1 Radio communication 4

4.2 Battery 4

5. Receiving the product 5

5.1 Delivery 5

5.2 Transporting the product 5

5.3 Inspecting the product 5

5.4 Handling the product 5

6. Applications 5

6.1 Pumped liquids 6

7. Mechanical installation 6

7.1 Pipes 7

7.2 Terminal box positions 8

7.3 Fitting of pump head 8

7.4 Base plate 9

7.5 Insulation 10

7.6 Frost protection 10

7.7 Cable entries 10

7.8 Ensuring motor cooling 10

7.9 Outdoor installation 10

8. Electrical installation 11

8.1 Protection against electric shock,

indirect contact 11

8.2 Cable requirements 11

8.3 Mains supply 12

8.4 Additional protection 13

8.5 Connection terminals 13

8.6 Signal cables 16

8.7 Bus connection cable 16

9. Startup 17

9.1 Flushing the pipe system 17

9.2 Priming the pump 17

9.3 Starting the pump 17

9.4 Shaft seal run-in 17

10. Operating conditions 18

10.1 Maximum number of starts and stops 18

10.2 Alternating operation of twin-head

pumps 18

10.3 Liquid temperature 18

10.4 Ambient temperature 18

10.5 Operating pressure or test pressure 18

10.6 Inlet pressure 18

10.7 Electrical data 18

10.8 Sound pressure level 18

10.9 Environment 18

10.10 Installation altitude 19

10.11 Humidity 19

10.12 Motor cooling 19

11. User interfaces 20

12. Standard control panel 20

12.1 Setpoint setting 21

13. Advanced control panel 23

14. Home display 24

14.1 Start-up guide 24

14.2 Menu overview for advanced control

panel 25

15. Grundfos GO 28

15.1 Communication 28

15.2 Menu overview for Grundfos GO main

menus 29

16. Description of functions 32

16.1 "Heat energy monitor" 32

16.2 Setpoint 32

16.3 Operating mode 32

16.4 Set manual speed 33

16.5 "Set user-defined speed" 33

16.6 Control mode 33

16.7 "Proportional-pressure setup" 40

16.8 FLOWLIMIT 40

16.9 Automatic Night Setback 41

16.10 Analog inputs 41

16.11 Built-in Grundfos sensor 43

16.12 Pt100/1000 inputs 43

16.13 Digital inputs 44

16.14 Digital inputs/outputs 45

16.15 "Signal relays 1 and 2" (Relay outputs) 47

16.16 Analog output 47

16.17 "Controller" ("Controller settings") 48

16.18 Operating range 50

16.19 External setpoint function 50

16.20 "Predefined setpoints" 52

16.21 "Temperature influence" 53

16.22 Limit-exceeded function 53

16.23 "Pulse flowmeter setup" 54

16.24 "Ramps" 55

16.25 "Standstill heating" 55

16.26 Motor bearing monitoring 55

16.27 "Service" 56

16.28 "Number" (Pump number) 56

16.29 "Radio communication" (Enable/disable

radio comm.) 56

16.30 Language 56

16.31 "Date and time" (Set date and time) 57

16.32 "Unit configuration" (Units) 57

16.33 "Buttons on product" (Enable/disable

settings) 57

16.34 Delete history 57

16.35 Define Home display 58

16.36 Display settings 58

16.37 "Store settings" (Store actual settings) 58

16.38 "Recall settings" (Recall stored settings) 58

16.39 "Undo" 58

English (GB)

1. Symbols used in this document

The text accompanying the three hazard symbols

DANGER, WARNING and CAUTION is structured in

the following way:

16.40 "Pump name" 58

16.41 "Connection code" 59

16.42 Run start-up guide 59

16.43 Alarm log 59

16.44 Warning log 60

16.45 Assist 60

16.46 Assisted pump setup 60

16.47 Setup, analog input 60

16.48 Setting of date and time 61

16.49 "Multipump setup" (Setup of multi-pump

system) 61

16.50 Description of control mode 64

16.51 Assisted fault advice 64

17. Selecting control mode 65

18. Bus signal 67

19. Priority of settings 68

20. Grundfos Eye 69

21. Signal relays 70

22. Installing a communication interface

module 71

23. Identification of functional module 73

24. Identification of control panel 73

25. Changing the position of the control

panel 74

26. Servicing the product 75

26.1 Maintenance 75

26.2 Service 75

27. Cleaning the product 76

28. Fault finding 76

29. Megging 78

30. Technical data, single-phase motors 78

30.1 Supply voltage 78

30.2 Leakage current 78

31. Technical data, three-phase motors 78

31.1 Supply voltage 78

31.2 Leakage current, AC 78

32. Inputs and outputs 79

33. Other technical data 80

33.1 Torques 81

33.2 Sound pressure level 81

34. Factory settings 82

35. Disposing of the product 83

Read this document before installing the

product. Installation and operation must

comply with local regulations and accepted

codes of good practice.

DANGER

Indicates a hazardous situation which, if

not avoided, will result in death or serious

personal injury.

WARNING

Indicates a hazardous situation which, if

not avoided, could result in death or

serious personal injury.

CAUTION

Indicates a hazardous situation which, if

not avoided, could result in minor or

moderate personal injury.

SIGNAL WORD

Description of hazard

Consequence of ignoring the warning.

- Action to avoid the hazard.

Tips and advice that make the work easier.

If these instructions are not observed, it

may result in malfunction or damage to the

equipment.

A blue or grey circle with a white graphical

symbol indicates that an action must be

taken.

A red or grey circle with a diagonal bar,

possibly with a black graphical symbol,

indicates that an action must not be taken

or must be stopped.

English (GB)

2. Abbreviations and definitions 3. General information

These installation and operating instructions apply to

the Grundfos TPE2, TPE2 D and TPE3, TPE3 D

pumps.

The pumps are fitted with frequency-controlled

permanent-magnet motors for single-phase or

three-phase mains connection.

4. General description

The pumps are fitted with frequency-controlled

permanent-magnet motors for single-phase or

three-phase mains connection.

4.1 Radio communication

This product incorporates a radio module for remote

control which is a class 1 device and can be used

anywhere in the EU member states without

restrictions.

For use in USA and Canada, see page 84.

Some variants of the product and products sold in

China and Korea have no radio module.

This product can communicate with Grundfos GO

and other products of the same type via the built-in

radio module.

In some cases, an external antenna may be

required. Only Grundfos-approved external antennas

may be connected to this product, and only by a

Grundfos-approved installer.

4.2 Battery

Pumps with the advanced functional module, FM

300, incorporate a Li-ion battery. The Li-ion battery

complies with the Battery Directive (2006/66/EC).

The battery does not contain mercury, lead and

cadmium.

AI Analog input

AL Alarm, out of range at lower limit

AO Analog output

AU Alarm, out of range at upper limit

CIM Communication interface module

Current

sinking

The ability to draw current into the

terminal and guide it towards earth in

the internal circuitry.

Current

sourcing

The ability to push current out of the

terminal and into an external load

which must return it to earth.

DI Digital input

DO Digital output

ELCB Earth-leakage circuit breaker

FM Functional module

GDS

Grundfos Digital Sensor

Factory-fitted sensor in some

Grundfos pumps

GENIbus Proprietary Grundfos fieldbus

standard

GFCI Ground fault circuit interrupter

USA and Canada

GND Earth

Grundfos

Eye Status indicator light

LIVE Low voltage with the risk of electric

shock if the terminals are touched

OC Open collector:

Configurable open-collector output

PE Protective earth

PELV

Protective extra-low voltage

A voltage that cannot exceed ELV

under normal conditions and under

single-fault conditions, except earth

faults in other circuits.

RCD Residual-current device

SELV

Safety extra-low voltage

A voltage that cannot exceed ELV

under normal conditions and under

single-fault conditions, including earth

faults in other circuits.

TPE2

Single-head pump without

factory-fitted differential-pressure and

temperature sensor

TPE2 D

Twin-head pump without factory-fitted

differential-pressure and temperature

sensor

TPE3

Single-head pump with factory-fitted

differential-pressure and temperature

sensor

TPE3 D

Twin-head pump with factory-fitted

differential-pressure and temperature

sensor

English (GB)

5. Receiving the product

5.1 Delivery

The pump is delivered from the factory in a carton

with a wooden bottom, specially designed for

transport by fork-lift truck or a similar vehicle.

5.2 Transporting the product

5.3 Inspecting the product

Before you install the product, do the following:

• Check that the product is as ordered.

• Check that no visible parts have been damaged.

If parts are damaged or missing, contact your local

Grundfos sales company.

5.4 Handling the product

Observe local regulations setting limits for manual

lifting or handling. The motor weight is stated on the

nameplate.

Lift the pump by means of nylon straps. See figures

1and 2.

Fig. 1 TPE2, TPE3

Fig. 2 TPE2 D, TPE3 D

6. Applications

The pumps are designed to circulate hot or cold

water in residential, institutional and industrial

applications:

• heating systems

• district heating plants

• central heating systems for blocks of flats

• air-conditioning systems

• cooling systems.

In addition, the pumps are used for liquid transfer

and water supply in for instance:

• washing systems

• domestic hot-water systems

• industrial systems in general.

To ensure optimum operation, the dimensioning

range of the system must fall within the performance

range of the pump.

WARNING

Falling objects

Death or serious personal injury

- Secure the product during

transportation to prevent it from tilting or

falling down.

CAUTION

Crushing of feet

Minor or moderate personal injury

- Wear safety shoes when moving the

product.

CAUTION

Back injury

Minor or moderate personal injury

- Use lifting equipment.

CAUTION

Crushing of feet

Minor or moderate personal injury

- Wear safety shoes and attach lifting

equipment to the motor eyebolts when

handling the product.

Do not lift the product by the terminal box.

TM05 7914 1613TM05 7915 1613

English (GB)

6.1 Pumped liquids

The pump is suitable for thin, clean, non-aggressive

and non-flammable liquids, not containing solid

particles or fibres that may attack the pump

mechanically or chemically.

Examples:

• Central heating system water. The water must

meet the requirements of accepted standards on

water quality in heating systems.

• Cooling liquids.

• Domestic hot water.

• Industrial liquids.

• Softened water.

The pumping of liquids with a density and/or

kinematic viscosity higher than that of water will have

the following effects:

• a considerable pressure drop

• a drop in hydraulic performance

• a rise in power consumption.

In such cases, fit the pump with a bigger motor. If in

doubt, contact Grundfos.

The EPDM O-rings fitted as standard are primarily

suitable for water.

If the water contains mineral or synthetic oils or

chemicals or if other liquids than water are pumped,

chose the O-rings accordingly.

7. Mechanical installation

Install the pump in a dry well-ventilated, but

frost-free position.

When installing pumps with oval bolt holes in the

pump flange, PN 6/10, use washers as shown in fig.

Fig. 3 Use of washers for oval bolt holes

Arrows on the pump housing show the direction of

flow of liquid through the pump.

You can install the pump in horizontal or vertical

pipes.

For inspection and removal of motor or pump head, a

clearance of 300 mm is required above the motor.

See fig. 4.

Fig. 4 Required clearance above the motor

WARNING

Contact with hazardous liquids

Death or serious personal injury

- If the pump is used for a liquid which is

injurious to health, it will be classified as

contaminated. In such cases, take

proper precautions to avoid injury to

health when operating or working on the

pump.

- Wear personal protection equipment.

WARNING

Hot or cold surface

Death or serious personal injury

- Make sure that no one can accidentally

come into contact with hot or cold

surfaces.

In order to maintain the UL mark,

additional requirements apply to the

equipment. See page 84.

TM01 0683 1997

The motor must never fall below the

horizontal plane.

TM05 7916 1613

Installation

Washer Pump

300 mm

English (GB)

Twin-head pumps installed in horizontal pipes must

be fitted with an automatic air vent in the upper part

of the pump housing. See fig. 5.

The automatic air vent is not supplied with the pump.

Fig. 5 Automatic air vent

If the liquid temperature falls below the ambient

temperature, condensation may form in the motor

during standstill. In this case, make sure that one of

the drain holes in the motor flange is open and points

downwards. See fig. 6.

Fig. 6 Drain hole in motor flange

If twin-head pumps are used for pumping liquids with

a temperature below 0 °C (32 °F), condensed water

may freeze and cause the coupling to get stuck. You

can solve the problem by installing heating elements.

Whenever possible, install the pump with the motor

shaft in horizontal position. See fig. 5.

7.1 Pipes

Fit isolating valves on either side of the pump to

avoid draining the system if the pump needs to be

cleaned or repaired.

The pump is suitable for pipeline mounting, provided

that the pipes are adequately supported on either

side of the pump.

Single-head pumps are designed for pipeline

mounting only.

Twin-head pumps are prepared for installation on a

mounting bracket or base plate.

When installing the pipes, make sure that the pump

housing is not stressed by the pipes.

The inlet and outlet pipes must be of an adequate

size, taking the pump inlet pressure into account.

To avoid sediment build-up, do not fit the pump at the

lowest point of the system.

Install the pipes so that air locks are avoided,

especially on the inlet side of the pump. See fig. 7.

Fig. 7 Correct pipes on the inlet side of the

pump

If there is any risk of the pump running against a

closed outlet valve, ensure a minimum liquid flow

through the pump by connecting a bypass or a drain

to the outlet pipe. The drain can for instance be

connected to a tank. A minimum flow rate of 10 % of

the flow rate at maximum efficiency is needed at all

times.

Flow rate and head at maximum efficiency are stated

on the pump nameplate.

TM05 7983 1713TM05 7917 1613

Observe the conditions in section

10. Operating conditions.

TM00 2263 0195

The pump must not run against a closed

outlet valve as this will cause an increase

in temperature or formation of steam in the

pump, which may cause damage to the

pump.

English (GB)

7.2 Terminal box positions

You can turn the terminal box to any position.

Change the terminal box position as follows:

1. Loosen the clamp securing the pump head to the

pump housing. See fig. 8.

Fig. 8 Clamp (A)

2. Turn the pump head to the required position.

3. Check the following before you tighten the clamp:

– The contact face of the pump housing and that

of the pump head must be in full contact.

– The clamp must be positioned correctly in the

flange recess of both the pump head and the

pump housing. See fig. 11.

Torque: 8 Nm (± 1 Nm).

7.3 Fitting of pump head

DANGER

Electric shock

Death or serious personal injury

- Switch off the power supply to the motor

and to the signal relays. Wait at least 5

minutes before you make any

connections in the terminal box. Make

sure that the power supply cannot be

accidentally switched on.

WARNING

Hazardous liquids

Death or serious personal injury

- If the pump is used for a liquid which is

injurious to health, it will be classified as

contaminated. In such cases, take

proper precautions to avoid injury to

health when operating or working on the

pump.

- Wear personal protection equipment.

WARNING

Falling objects

Death or serious personal injury

- If the pump head has been lifted partly

or completely from the pump housing,

pay special attention when fitting the

pump head again.

CAUTION

Crushing of feet

Minor or moderate personal injury

- Wear safety shoes.

- Pay special attention that the pump

head does not fall down when loosening

the clamp. See fig. 8.

WARNING

Pressurised system

Death or serious personal injury

- Pay special attention to any escaping

vapour when loosening the clamp. See

fig. 8.

- Wear personal protection equipment.

TM06 0721 0814

DANGER

Electric shock

Death or serious personal injury

- Switch off the power supply to the motor

and to the signal relays. Wait at least 5

minutes before you make any

connections in the terminal box. Make

sure that the power supply cannot be

accidentally switched on.

WARNING

Falling objects

Death or serious personal injury

- If the pump head has been lifted partly

or completely from the pump housing,

pay special attention when fitting the

pump head again.

English (GB)

If for some reason the pump head has been lifted

from the pump housing, follow the following

procedure in order to mount the pump head

correctly:

1. Visually check that the neck ring is centred in the

pump housing. See fig. 9.

Fig. 9 Centring of neck ring

2. Gently lower the pump head with rotor shaft and

impeller into the pump housing. See fig. 10.

Fig. 10 Lowering of pump head

3. Check the following before you tighten the clamp:

– The contact face of the pump housing and that

of the pump head must be in full contact.

– The clamp must be positioned correctly in the

flange recess of both the pump head and the

pump housing. See fig. 11.

Torque: 8 Nm (± 1 Nm).

Fig. 11 Positioning of clamp ring

7.4 Base plate

Twin-head pumps have tapped holes in the bottom of

the pump housing. You can use the holes for

mounting a base plate.

CAUTION

Crushing of feet

Minor or moderate personal injury

- Wear safety shoes.

- Pay special attention that the pump

head does not fall down when loosening

the clamp. See fig. 8.

WARNING

Pressurised system

Death or serious personal injury

- Pay special attention to any escaping

vapour when loosening the clamp. See

fig. 8.

- Wear personal protection equipment.

TM06 0722 0814

TM06 0723 0814TM06 0724 0814

English (GB)

7.5 Insulation

Follow the guidelines in fig. 12 when insulating the

pump.

Fig. 12 Insulation of TPE2, TPE3 pumps

7.6 Frost protection

Drain pumps which are not being used during

periods of frost to avoid damage.

7.7 Cable entries

See the size of the cable entries in section 33. Other

technical data.

7.8 Ensuring motor cooling

Leave at least 50 mm between the end of the fan

cover and a wall or other fixed objects. See fig. 13.

Fig. 13 Minimum distance, D, from the motor to

a wall or other fixed objects

7.9 Outdoor installation

If you install the motor outdoors, provide the motor

with a cover and open the drain holes to avoid

condensation on the electronic components. See fig.

14.

The cover must be sufficiently large to ensure that

the motor is not exposed to direct sunlight, rain or

snow. Grundfos does not supply covers. We

therefore recommend that you have a cover built for

the specific application. In areas with high humidity,

we recommend that you connect the motor

permanently to the mains supply and activate the

built-in standstill heating function. See section

16.25 "Standstill heating".

Fig. 14 Examples of covers, not supplied by

Grundfos

Do not insulate the motor stool as this will

trap any vapour escaping from the shaft

seal, thus causing corrosion. Covering the

motor stool with insulation will also make

inspection and service difficult.

TM05 7918 1613

Pos. Description

A Without insulation

B Correct insulation

C Incorrect insulation

TM05 5236 3512

When fitting a cover to the motor, observe

the guidelines in section 7.8 Ensuring

motor cooling.

TM05 3496 3512

In order to maintain the UL mark,

additional requirements apply to the

equipment. See page 84.

Autres manuels pour TPE 2 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Grundfos Pompe à eau

Grundfos

Grundfos DME 60-940 l/h Manuel d'utilisation

Grundfos

Grundfos COMFORT PM B Manuel utilisateur

Grundfos

Grundfos Conlift1 LS Manuel utilisateur

Grundfos

Grundfos MGE F Mode d'emploi

Grundfos

Grundfos SCALA1 Manuel d'utilisation

Grundfos

Grundfos MAGNA3 25-100 (N) Manuel utilisateur

Grundfos

Grundfos DDI 222 Series Manuel utilisateur

Grundfos

Grundfos 72 Mode d'emploi

Grundfos

Grundfos ALPHA1 B Manuel utilisateur

Grundfos

Grundfos JP Series Manuel utilisateur

Grundfos

Grundfos MAGNA3 25-80 (N) Manuel utilisateur

Grundfos

Grundfos CMB-SP Booster PM2 Manuel d'utilisation

Grundfos

Grundfos 2000 Series Manuel utilisateur

Grundfos

Grundfos SQ Manuel utilisateur

Grundfos

Grundfos UPS 200 Series Manuel utilisateur

Grundfos

Grundfos Unilift KP 250 Manuel utilisateur

Grundfos

Grundfos DMS D Series Manuel utilisateur

Grundfos

Grundfos CMBE TWIN Manuel utilisateur

Grundfos

Grundfos SL1 Series Manuel utilisateur

Grundfos

Grundfos SCALA1 Manuel utilisateur

Grundfos

Grundfos PS.R.05-17 Manuel utilisateur

Grundfos

Grundfos SEG Series Manuel utilisateur

Grundfos

Grundfos TPE Series Manuel utilisateur

Grundfos

Grundfos SP-NE Series Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur