Grundfos CR 32 Mode d'emploi

GRUNDFOS INSTRUCTIONS

CR, CRN 32-90 Model B

Standard model

Service instructions

English (US)

3. Service tools

ABC

DEF

GH I

JKL

MNO

Pos. Designation For pos. Tool size Product No

ARing/open-

end spanner

18, 23 24 mm SV0122

28 8 mm SV0273

36 24 mm SV0122

BRubber

hammer SV0349

C Hexagon key

9 8 mm SV0032

113 3 mm -

28 8 mm SV0032

58a 8 mm SV0032

DTorque

screwdriver 113, 7a .1-4 ft.-lbs./

1-6 Nm SV0435

SV0438

E Hexagon bit 98mm -

113 3 mm -

28 8 mm -

FTorque

wrench 9, 18, 23,

28, 36, 58 15-74 ft.-lbs./

20-100 Nm SV0269

GRing insert

tool

18, 23 24 mm SV0524

28 8 mm SV0411

36 24 mm SV0524

HKey for split

cone nut 48 34 mm SV0004

ITap for key

for split cone

nut 48-K 14 mm

9 x 12 mm SV0403

Holder with

pin for

dismantling

and

assembly

80 -

CR,CRN32

SV0003-3

CR,CRN45

SV0003-4

CR,CRN64

SV0003-5

CR,CRN90

SV0003-2

KHolder for

wear ring 49c -

CR,CRN32

SV0043

CR,CRN45

SV0044

CR,CRN64

SV0045

CR,CRN90

SV0046

LPuller for

wear ring 49c - SV0239

MPunch for

complete

neck ring 45a -

CR,CRN32

SV0025

CR,CRN45

SV0027

CR,CRN64

SV0028

CR,CRN90

SV0029

NPunch for

bush 47c-47d - SV0015

OHook

spanner 49-49a - SV0031

PAdjusting

fork 105 22 mm 985924

Q Eye bolt 28b ID2779

English (US)

4. Torques

5. Lubricants

6. Pump dismantling

Position numbers refer to the drawings in section 11. Exploded

views.

6.1 Motor

1. Remove screws (pos. 7a) and coupling guards (pos. 7).

2. Remove screws (pos. 9) and coupling (pos. 8). It may be

necessary to loosen the coupling with a rubber hammer.

3. Remove screws (pos. 28). Lift and remove motor and motor

stool (pos. 1a) with lifting straps that pass through the motor

stool. Ensure that the motor does not tip and the load is not

applied to the pump shaft.

6.2 Shaft seal and pump head

1. Remove screws (pos. 58a) and retainer (pos. 58).

2. Clean end of shaft (pos. 51).

3. Slacken set screws (pos. 113) of shaft seal (pos. 105).

4. Carefully press shaft seal out of pump head (pos. 2) using two

slot screwdrivers, and pull it off the shaft. See fig. 1.

Fig. 1 Removing upper shaft seal

5. Remove nuts (pos. 36) and washers (pos. 66a).

6. Remove pump head (pos. 2). It may be necessary to loosen it

with a rubber hammer.

Pos. Description Dimensions Torque

7a Coupling guard

screws - 4.4 ft-lbs./6 Nm

9 Coupling screws M10 x 25 mm 63 ft-lbs./85 Nm

18 Air vent screws - 26 ft-lbs./35 Nm

23 Drain plugs 1/2"

26b Screws for straps - 11 ft-lbs./15 Nm

28 Motor stool screws M10 x 50 mm 46 ft-lbs./62 Nm

36 Pump head nuts M16 74 ft-lbs./100 Nm

48 Spit cone nut - 52 ft-lbs./70 Nm

58a Seal carrier screws M10 x 25 mm 46 ft-lbs./62 Nm

113 Shaft seal set screws - 4 ft-lbs./6 Nm

Pos. Description Lubricant Product No

9 Coupling screws THREAD-EZE 00SV999728 Motor stool screws

58a Seal carrier screws

51 Shaft Soapy water -

105 Shaft seal

37 O-ring pump housing Rocol

Sapphire

Aqua-Sil 00RM2924

47 Bearing ring

109 O-ring shaft seal

110 O-ring shaft seal

Caution

To prevent the motor from tipping over, hold it

straight when using a lifting device.

Do not use the lifting eyes of the motor for lifting

the entire pump and motor assembly.

TM060090 4813

English (US)

6.3 Chamber stack

6.3.1 Fitting chamber stack on the holder

1. Place the holder for dismantling and assembly in a vice and

tighten it. See fig. 2 for right positioning.

2. Pull the chamber stack out of the outer sleeves (pos. 55) and

place it in the holder according to fig. 2. Make sure the

chamber stack engages with the holder.

3. Fit the locking pin in the hole marked "Dismantling".

Fig. 2 Positioning the chamber stack in the holder

4. Remove screws (pos. 26b) and washers (pos. 26c).

5. Remove straps (pos. 26a).

6.3.2 Dismantling chambers

Depending on their construction, dismantle the chambers

according to the instructions below. The symbols refer to section

10. Order of assembly for chambers and impellers.

Single chamber

Fig. 3 Single chamber

1. Pull apart the rotating spring of the bearing (pos. 47a) and

remove the bearing.

2. Hold impeller (pos. 49) with the hook spanner, and slacken

split cone nut (pos. 48) using the key for split cone nut. Turn

the key around and knock the nut to loosen the impeller from

the split cone (pos. 49b).

3. Pull the split cone nut, split cone and impeller off the shaft.

Top chamber and chamber without bearing

Fig. 4 Left: top chamber; right: chamber without bearing

1. Loosen chamber (pos. 3) from the chamber below using a

screwdriver, and remove it.

2. Hold impeller (pos. 49) with the hook spanner, and slacken

split cone nut (pos. 48) using the key for split cone nut.

Turn the key around, and knock the nut to loosen the impeller

from split cone (pos. 49b).

3. Pull the split cone nut, split cone and impeller off the shaft.

Chamber with bearing

Fig. 5 Chamber with bearing

1. Loosen chamber (pos. 4a) from the chamber below or inlet

part (pos.44) using a screwdriver.

2. Loosen bearing ring (pos. 47a) from split cone nut (pos. 48)

and pull it off the shaft.

3. Hold impeller (pos. 49) with the hook spanner, and slacken

split cone nut (pos. 48) using the key for split cone nut.

Turn the key around, and knock the nut to loosen the impeller

from split cone (pos. 49b).

4. Pull the split cone nut, split cone and impeller off the shaft.

5. When the last impeller has been removed, inlet part (pos. 44)

can be lifted off the holder.

TM060180 5013

English (US)

8.1.2 Assembly

1. Place neck ring (pos. 45) in cup (pos. 46).

2. Fit neck ring retainer (pos. 65) with the four driving dogs

pointing downwards. Turn the neck ring retainer until it

engages with the neck ring.

3. Knock/press the neck ring retainer home against the cup

using the punch for complete neck ring. Check that the

measurement is within the tolerance range. See fig.10.

Fig. 10 Measure distance between retainer and top of cup

4. Fit the complete neck ring in chamber (pos. 4/4a) or inlet part

(pos. 44) and knock/press it home using the punch for

complete neck ring.

8.2 Wear ring (pos. 49c)

8.2.1 Dismantling

1. Fit the holder on the impeller. The wear ring should come out

in the center of the holder. See fig 11.

2. Place the impeller and holder on a flat surface, the wear ring

uppermost.

3. Push the wear ring up and free of the impeller using the puller.

See fig. 11.

Fig. 11 Removing wear ring

8.2.2 Assembly

Press wear ring (pos. 49c) carefully down over impeller skirt

(pos. 49/49a).

8.3 Bush (pos. 47c) and retaining ring (pos. 47d)

8.3.1 Dismantling

Place the chamber on a flat surface, and press the bush and

retaining ring down using the punch for bush.

8.3.2 Assembly

Place the chamber on a level and solid surface with complete

neck ring (pos. 45a) facing downwards, and press the bush and

retaining ring home against the chamber using the punch for

bush.

TM011955 2201

Pump Nominal height, X [in. (mm)] Tolerance range

[in. (mm)]

CR, CRN 32 0.40" (10.1 mm)

± .007" (0.2 mm)

CR, CRN 45 0.61" (15.5 mm)

CR, CRN 64 0.45" (11.5 mm)

CR, CRN 90 0.48" (12.1 mm)

Note

It should be possible to move the neck ring freely

(sideways) between the neck ring retainer and

the cup.

TM007233 0996

Caution

Make sure to push the ring straight down against

the impeller skirt. Make sure not to damage the

impeller.

English (US)

Single chamber

Fig. 17 Single chamber

1. Fit impeller (pos. 49) and press it home.

2. Fit split cone (pos. 49b) and knock it into the impeller hub

using the key for split cone nut.

3. Hold the impeller with the hook spanner. Fit and tighten split

cone nut (pos. 48).

4. Slide bearing ring (pos. 47a) over the split cone nut. It must

engage with the split cone nut.

5. Fit chamber (pos. 3). Turn it so that the holes for straps are

aligned to the fixing lugs for straps on the inlet part.

6. Press the chamber home against inlet part (pos. 44).

7. Fit straps (pos. 26a) and washers (pos. 26c), and cross-

tighten screws (pos. 26b).

9.2 Pump head and shaft seal

1. Replace rubber springs (pos. 60) and O-ring (pos. 37).

2. Fit pump head (pos. 2) on outer sleeves (pos. 55).

3. Fit washers (pos. 66a) and cross-tighten nuts (36).

4. Carefully press shaft seal (pos. 105) down the shaft and in the

pump head.

5. Fit retainer (pos. 58) and cross-tighten screws (58a).

6. Press the pump shaft home and tighten set screws (pos. 113).

7. Lift the pump shaft and insert the adjusting fork between the

shaft seal driver and its retainer. See fig. 18.

Fig. 18 Fitting adjusting forks

9.3 Motor

1. With lifting straps that pass through the motor stool, lift and fit

the motor and motor stool (pos. 1a) to the pump head (pos. 2).

Ensure that the motor does not tip and the load is not applied

to the pump shaft.

2. Cross-tighten screws (pos. 28).

3. Fit coupling (pos. 8), according to fig. 19 and 20, and tighten

screws (pos. 9).

Fig. 19 Fitting coupling

Fig. 20 Adjusting coupling

4. Remove the adjusting fork, and place it under one of screws

(pos. 58a).

5. Check that the pump shaft can rotate freely.

6. Fit coupling guards (pos. 7) and screws (pos. 7a).

TM060071 4813

Caution

To prevent the motor from tipping over, hold it

straight when using a lifting device.

Do not use the lifting eyes of the motor for lifting

the entire pump and motor assembly.

TM05 7578 1213TM03 9607 4207

Autres manuels pour CR 32

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Grundfos Pompe à eau

Grundfos

Grundfos SRG 60 Hz Manuel utilisateur

Grundfos

Grundfos Conlift1 LS Manuel utilisateur

Grundfos

Grundfos MAGNA1 D Manuel utilisateur

Grundfos

Grundfos SPK Series Manuel utilisateur

Grundfos

Grundfos MTH Series Manuel utilisateur

Grundfos

Grundfos UPE 50-120 Manuel utilisateur

Grundfos

Grundfos BMS Series Manuel utilisateur

Grundfos

Grundfos alpha2 l Manuel utilisateur

Grundfos

Grundfos DPK Manuel utilisateur

Grundfos

Grundfos MGE 71 Series Manuel utilisateur

Grundfos

Grundfos DME series Manuel utilisateur

Grundfos

Grundfos MAGNA 2000 Series Manuel utilisateur

Grundfos

Grundfos NB Manuel utilisateur

Grundfos

Grundfos SEG Series Manuel utilisateur

Grundfos

Grundfos CM Manuel utilisateur

Grundfos

Grundfos SCALA2 Manuel utilisateur

Grundfos

Grundfos SRP Series Manuel utilisateur

Grundfos

Grundfos BMPX Manuel utilisateur

Grundfos

Grundfos SCALA1 Manuel d'utilisation

Grundfos

Grundfos DDI 222 Series Manuel utilisateur

Grundfos

Grundfos SRG Series Manuel utilisateur

Grundfos

Grundfos TPE 2 Series Manuel d'utilisation

Grundfos

Grundfos Unilift AP12 Manuel utilisateur

Grundfos

Grundfos CM SP Mode d'emploi

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur