Grizzly T32057 Manuel utilisateur

DO NOT modify or alter this cutterhead to

make it fit other makes or models of joint-

ers for which it is not designed. Doing so

could result in property damage or serious

personal injury.

Figure 1. Model T32057 inventory.

The Model T32057 8" Helical Cutterhead is

designed to replace the straight-knife cutterhead

on the Model G0855 8" x 72" Jointer.

Inventory (Figure 1)

Description Qty

A. Helical Cutterhead Assembly ...................... 1

B. T-Handle Torx Drivers T25 .......................... 2

C. Flat Hd Torx Screws T25 10-32 x 1⁄2" ........ 10

D. Indexable Inserts 15 x 15 x 2.5mm ............. 5

Introduction

Specifications

Maximum Width of Cut ...................................... 8"

Cutterhead Diameter .....................................31⁄16"

Number of Indexable Carbide Inserts .............. 36

Indexable Carbide Insert Size ....15 x 15 x 2.5mm

Tools Needed

• Pair of Heavy Leather Gloves ..................... 1

• Safety Glasses (per person) ........................ 1

• Phillips Head Screwdriver #2 ...................... 1

• Flat Head Screwdriver ................................. 1

• Adjustable Wrench ...................................... 1

• Precision Straightedge 36" .......................... 1

• Feeler Gauge Set ........................................ 1

• Shop Rag .................................... As Needed

• Degreaser .................................... As Needed

The total installation/setup procedure takes

approximately half an hour. Read these instruc-

tions thoroughly before beginning.

Note: Not all pictures in these instructions will

exactly reflect your machine. Some photos are

provided for representation purposes only to help

you better understand the instructions given.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 04/20) #KS21092 PRINTED IN TAIWAN V1.05.20

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T32057

8" HELICAL CUTTERHEAD

ASSEMBLY FOR G0855

INSTRUCTIONS

Jointer knives are extremely sharp. You

must remove the jointer knives, or mount

the knives blade side down to avoid the risk

of serious personal injury during the follow-

ing steps.

Figure 2. Example of jointer disassembly Steps

1– 4.

Figure 3. Example of removing hex nut and flat

washer on bearing block stud.

Figure 4. Example of cutterhead removed.

Bearing

Block Stud

Bearing

Block

-2- T32057 8" Helical Cutterhead Assembly

5. Remove nut and flat washer on bearing block

stud, as shown in Figure 3, and repeat on the

other side.

6. Wearing heavy leather gloves, carefully

remove the cutterhead from the casting (see

Figure 4).

Note: Your cutterhead may have paper shims

stuck to the bearing block or where the bear-

ing block rests. These were included at the

factory when they calibrated your cutterhead

to be even with the outfeed table. Your new

cutterhead may or may not need these. If

you see any shims, carefully pull them off

and set them aside for later use—or keep

them with your cutterhead in the event that

you re-install it later. Also, mark the side of

the cutterhead where they were used, so the

future install will go smoothly.

7. Remove bearing block studs from bearing

blocks.

Removing Existing Cutterhead

1. DISCONNECT MACHINE FROM POWER!

2. Remove jointer fence, cutterhead guard, and

rabbeting table.

3. Remove rear access panel and belt cover,

then remove V-belt from pulleys.

4. Lower both tables to make enough room for

the cutterhead to come out (see Figure 2).

Note: When lowering, make sure that the

fence support does not come in contact with

the cutterhead pulley.

Jointer carbide inserts are extremely sharp.

Wear leather gloves to avoid the risk of

serious personal injury during the following

steps.

Figure 5. Example of helical cutterhead installed.

Straightedge

Outfeed Table

Figure 6. Checking cutterhead parallelism.

T32057 8" Helical Cutterhead Assembly -3-

Installing Helical Cutterhead

1. Install cutterhead (see Figure 5) with bearing

block studs, flat washers, and hex nuts previ-

ously removed.

2. Tighten helical cutterhead in place, and

ensure pulley set screw is tight.

3. Using straightedge and feeler gauge set,

inspect cutterhead parallelism with outfeed

table as shown in Figure 6. With straightedge

in position, raise or lower outfeed table until

cutterhead body (not the carbide insert) just

touches straightedge.

4. Move straightedge to the other side to deter-

mine if one end of cutterhead body is higher/

lower than the other. (Place feeler gauge

between cutterhead body and straightedge to

determine the height difference.)

— If cutterhead is even or within 0.003" with

outfeed table from one side to other, skip

to Step 7.

— If cutterhead is over 0.003" from one side

to other, go to Step 5.

5. Loosen hex nuts securing both bearing block

studs, lift helical cutterhead slightly, then

place a shim beneath bearing block that

needs to be adjusted.

Note: Use shims from your old cutterhead

if available. If not available, newspaper is

approximately 0.003" thick and will work for

shimming (we don't recommend shimming

more than 0.003" on either side, as this may

affect how the bearing block seats in the

casting).

6. Repeat Steps 3–5 and adjust as necessary,

then tighten hex nuts on bearing block studs.

Figure 7. Cutterhead insert at top-dead-center.

Straightedge

Outfeed Infeed

-4- T32057 8" Helical Cutterhead Assembly

7. Place a straightedge on outfeed table

so it extends over cutterhead, and rotate

cutterhead pulley until one of the carbide

inserts is at top-dead-center (TDC), as shown

in Figure 7.

8. Lock outfeed table, then re-install fence.

9. Re-install V-belt on pulleys. (Refer to instruc-

tions in your G0855 manual for details.)

10. Re-install rabbeting table, rear access panel,

and belt cover.

11. Install cutterhead guard back over cutterhead,

making sure that spring tension in guard

is properly set so guard springs back over

cutterhead when it is pulled back and

released.

When correctly set, carbide insert will just

touch straightedge when insert is at its high-

est point of rotation (see Figure 7).

— If your outfeed table is correctly set, no

adjustments are necessary.

— If insert lifts straightedge off table or if

table is below straightedge, adjust outfeed

table height with handwheel until straight-

edge just touches an insert at its highest

point of rotation.

Figure 8. Rotating indexable carbide inserts.

Reference Dot

T32057 8" Helical Cutterhead Assembly -5-

Installing or adjusting a carbide insert:

1. DISCONNECT MACHINE FROM POWER!

2. Remove any sawdust from head of carbide

insert Torx screw.

3. Remove Torx screw and carbide insert.

4. Clean all dust and dirt off insert and cutterhead

pocket from which insert was removed, and

replace insert so a fresh, sharp edge is facing

outward.

Note: Proper cleaning is critical to achiev-

ing a smooth finish. Dirt or dust trapped

between insert and cutterhead will slightly

raise insert, and make noticeable marks on

your workpieces the next time you cut.

5. Lubricate Torx screw threads with a light

machine oil, wipe excess oil off threads, and

torque Torx screw to 48-50 INCH pounds.

Note: Excess oil may squeeze between insert

and cutterhead or in screw hole, thereby lifting

insert or screw slightly and affecting work-

piece finishes.

In addition, each insert has a reference dot on

one corner. As the insert is rotated, the reference

dot location can be used as an indicator of which

edges are used and which are new. The insert

must be replaced when all four edges are dull.

Rotating Inserts

The cutterhead is equipped with 36 indexable car-

bide inserts. Each insert can be rotated to reveal

any one of its four cutting edges. Therefore, if one

cutting edge becomes dull or damaged, simply

rotate it clockwise 90˚ to reveal a fresh cutting

edge (see Figure 8).

Tools Needed

• Pair of Heavy Leather Gloves ..................... 1

• Safety Glasses (per person) ........................ 1

• T-Handle Torx Driver T25 ........................... 1

• Torque Wrench 0–50 in.-lb. ......................... 1

• Shop Rag .................................... As Needed

• Degreaser .................................... As Needed

• Light Machine Oil ........................ As Needed

Figure 10. Assortment of basic eye protection.

Basic Eye Protection

T20501—Face Shield Crown Protector 4"

T20502—Face Shield Crown Protector 7"

T20503—Face Shield Window

T20451—“Kirova” Clear Safety Glasses

T20452—“Kirova” Anti-Reflective S. Glasses

T20456—DAKURA Safety Glasses, Black/Clear

T20451

T20452

T20502

T20503

T20456

Figure 11. G0860 Portable Dust Collector.

Figure 9. H9893 Indexable Carbide Inserts.

-6- T32057 8" Helical Cutterhead Assembly

Accessories

H9893—10 Pack of Indexable Carbide Inserts

Replacement 15 x 15 x 2.5mm carbide inserts for

Model T32057 8" Helical Cutterhead.

G0860—1½ HP Portable Cyclone Dust Collector

This compact unit features an impressive 868

CFM and up to 9.7" of static pressure —perfect

for handling up to two large machines at once.

The 20 gallon collection drum with quick release

handle catches large particulate for quick and

clean bag changes, and the pleated 1-micron filter

captures remaining dust as part of this super effi-

cient two stage separation system. All this, and it

features a wireless remote!

3-1

3-2

3-3

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT32057001 BEARING BLOCK 3-3 PT32057003-3 INSERTS 15 X 15 X 2.5MM-10 PK

2 PT32057002 BALL BEARING 6204-2NSE 4 PT32057004 KEY 5 X 5 X 30 RE

3 PT32057003 HELICAL CUTTERHEAD ASSEMBLY 5 PT32057005 CUTTERHEAD PULLEY

3-1 PT32057003-1 CUTTERHEAD 8" HELICAL 6 PT32057006 SET SCREW M6-1 X 8

3-2 PT32057003-2 FLAT HD TORX SCR T-25 10-32 X 1/2 7 PT32057007 T-HANDLE TORX DRIVER T-25

T32057 8" Helical Cutterhead Assembly -7-

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

T32057 Parts Breakdown & List

We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown

are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability.

Table des matières

Autres manuels Grizzly Outils électriques

Grizzly

Grizzly G0473 Guide de démarrage rapide

Grizzly

Grizzly H2801 Manuel utilisateur

Grizzly

Grizzly T1243 Manuel utilisateur

Grizzly

Grizzly G0612 Manuel utilisateur

Grizzly

Grizzly G8994Z Manuel utilisateur

Grizzly

Grizzly G0747 Manuel utilisateur

Grizzly

Grizzly H0800 1200W Manuel utilisateur

Grizzly

Grizzly G0836 Manuel utilisateur

Grizzly

Grizzly Extreme Series Manuel utilisateur

Grizzly

Grizzly Extreme Series Manuel utilisateur

Grizzly

Grizzly G0875 Manuel utilisateur

Grizzly

Grizzly G0455 Manuel utilisateur

Grizzly

Grizzly G0796 Manuel utilisateur

Grizzly

Grizzly G0543 Manuel utilisateur

Grizzly

Grizzly H2867 Manuel utilisateur

Grizzly

Grizzly G0931 Manuel utilisateur

Grizzly

Grizzly H8000 Manuel utilisateur

Grizzly

Grizzly G0813 Manuel utilisateur

Grizzly

Grizzly AGS 72 Lion-Set Instructions d'utilisation et d'installation

Grizzly

Grizzly G0490 Guide de démarrage rapide

Grizzly

Grizzly H8090 Manuel utilisateur

Grizzly

Grizzly G1049 Manuel utilisateur

Grizzly

Grizzly WOOD MILL G9959 Manuel utilisateur

Grizzly

Grizzly WOOD MILL G9959 Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel