Grizzly T32840 Manuel utilisateur

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 11/21) #CS22153 PRINTED IN TAIWAN

Introduction

The Model T32840 Sliding Log Miter Table cuts

0°–45° angles left or right on vertical wood-cutting

bandsaws when used with the T32838 Bandsaw

Sled. The miter body features adjustable stops at

90°, 30° left, and 30° right.

Inventory

V1.11.21

Figure 1. T32840 inventory.

Description Qty

A. Work Stop ................................................... 1

B. Fence.......................................................... 1

C. T-Bolts 1⁄4"-20 x 11⁄2" .................................... 2

D. Knobs 1⁄4"-20 ............................................... 3

E. Miter Table .................................................. 1

F. Flat Washer 1⁄4" ........................................... 1

G. Hex Bolt 1⁄4"-20 x 1⁄2" ................................... 1

Assembly

Wear safety glasses during

the entire setup process!

NOTICE

If you cannot find item on list, check around/

inside packaging materials. Often, items

get lost in packaging while unpacking or

they are pre-installed at factory.

The Model T32840 must be assembled before it

can be mounted on the T32838 bandsaw sled.

To assemble miter table:

1. Slide (2) 1⁄4"-20 x 11⁄2" T-bolts into fence T-slot

(see Figure 2).

Figure 2. T-bolts installed in fence T-slot.

x 2

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T32840

SLIDING LOG MITER

TABLE

INSTRUCTIONS

-2- Model T32840 (Mfd. Since 11/21)

Using Jig

Items Needed Qty

Vertical Bandsaw ............................................... 1

T32838 Bandsaw Sled ...................................... 1

To reduce risk of eye injury from flying

chips or lung damage from breathing dust,

always wear safety glasses and a respirator

when operating bandsaw.

To use jig:

1. Refer to Model T32838 Instructions to

install bandsaw sled on bandsaw.

2. DISCONNECT BANDSAW FROM POWER!

3. Align tracks of miter table with tracks of

bandsaw sled, then slide jig onto sled (see

Figure 6).

2. Attach fence to miter table by threading (2)

1⁄4"-20 knobs onto T-bolts (see Figure 3).

Figure 3. Attaching fence to miter table.

Miter Table

Fence

3. Slide 1⁄4"-20 x 1⁄2" hex bolt into top slot of fence

(see Figure 4).

Figure 4. Hex bolt installed in fence top slot.

4. Attach work stop to fence with 1⁄4"-20 knob,

1⁄4" flat washer, and hex bolt from Step 3, as

shown in Figure 5.

Figure 5. Attaching work stop to fence.

Mount the Model T32840 on the tracks of the

T32838 Bandsaw Sled to smoothly feed logs

across the table of your bandsaw.

IMPORTANT: Refer to the bandsaw manual for

information on safely operating your bandsaw.

Work

Stop

Figure 6. Sliding miter table onto bandsaw sled.

Tracks

Miter Table

Sled

4. Loosen miter gauge handle, then rotate miter

gauge until pointer on scale indicates desired

angle (see Figure 7).

Model T32840 (Mfd. Since 11/21) -3-

Note: If workpiece is short enough, adjust

work stop against workpiece edge to keep it

from drifting during cut (see Figure 9).

7. Connect bandsaw to power, turn bandsaw

ON, then slide table forward on sled to feed

workpiece through blade and to complete cut.

Note: Pull pin shown in Figure 7 to adjust

angle to the left.

5. Loosen (2) knobs shown in Figure 8, slide

fence out of blade path, then tighten knobs to

secure.

Figure 8. Fence adjusted out of blade path.

Knob

(1 of 2)

Figure 7. Miter adjustment components.

Pointer

Miter

Gauge

Handle

Figure 9. Workpiece resting against fence with

work stop adjusted for repeatable cuts.

Work Stop

Fence

Workpiece

Adjusting Stops

Check the accuracy of the fence when adjusted

to the 90°, 30° left, and 30° right stops. If a stop

is not accurate, loosen the jam nut, adjust the

Phillips head screw until the fence is the correct

angle, then tighten the jam nut to secure (see

Figure 10).

Figure 10. Stop components (30° right shown).

Items Needed Qty

Combination Square or Protractor ..................... 1

Open-End Wrench 3⁄8" ....................................... 1

Phillips Head Screwdriver #2 ............................ 1

6. Rest workpiece against fence, aligning blade

with intended line of cut (see Figure 9).

Center of

Gravity

If workpiece center of gravity (see Figure

9) extends too far right, table can easily

tip off of bandsaw sled. Body parts could

be pulled into moving blade or pinched/

crushed if caught under falling workpiece.

If table is not firmly seated on bandsaw

sled, use roller table (or other method of

workpiece support) or cut down workpiece

to more manageable length.

-4- Model T32840 (Mfd. Since 11/21)

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

T32840 Parts Breakdown & List

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here

are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT32840001 MI TER TABLE 10 PT32840010 FLAT WASHER 6MM

2 PT32840002 FENCE 11 PT32840011 FLAT WASHER 6MM PLASTIC

3 PT32840003 TRACK 12 PT32840012 POINTER PLATE

4 PT32840004 MI TER BODY 13 PT32840013 LOCK BRACKET

5 PT32840005 FIXED HANDLE 28 X 72, M6-1 X 24 16 PT32840016 HEX BOLT 1/4-20 X 1/2

6 PT32840006 POINTER BODY ASSEMBLY 17 PT32840017 FLAT WASHER 1/4

7 PT32840007 BUTTON HD CAP SCR M5-.8 X 10 18 PT32840018 FLANGE TAP SCREW 8 X 1/2

8 PT32840008 KNOB 1/4-20, 3-LOBE, D1-1/8 19 PT32840019 PHLP HD SCR 10-24 X 7/8

9 PT32840009 T-BOLT 1/4-20 X 1-1/2 20 PT32840020 HEX NUT 10-24

Autres manuels Grizzly Équipement industriel

Grizzly

Grizzly T32718 Manuel utilisateur

Grizzly

Grizzly G0950 Manuel utilisateur

Grizzly

Grizzly G0877 Manuel utilisateur

Grizzly

Grizzly G0479 Manuel utilisateur

Grizzly

Grizzly T32716 Manuel utilisateur

Grizzly

Grizzly T33447 Manuel utilisateur

Grizzly

Grizzly G9980 Manuel utilisateur

Grizzly

Grizzly T32710 Manuel utilisateur

Grizzly

Grizzly T32537 Manuel utilisateur

Grizzly

Grizzly T33850 Manuel utilisateur

Grizzly

Grizzly G0718 Manuel utilisateur

Grizzly

Grizzly G0656P Manuel utilisateur

Grizzly

Grizzly T28173 Manuel utilisateur

Grizzly

Grizzly T26472Z Manuel utilisateur

Grizzly

Grizzly G0714 Manuel utilisateur

Grizzly

Grizzly G0876 Manuel utilisateur

Grizzly

Grizzly G0937 Manuel utilisateur

Grizzly

Grizzly T24631 Manuel utilisateur

Grizzly

Grizzly G0526A40 Manuel utilisateur

Grizzly

Grizzly H7590 Manuel utilisateur

Grizzly

Grizzly G0738 Manuel utilisateur

Grizzly

Grizzly T20798 Manuel utilisateur

Grizzly

Grizzly G0707 Manuel utilisateur

Grizzly

Grizzly T10460 Manuel utilisateur

Manuels Équipement industriel populaires d'autres marques

ABB

ABB Unifix AD Manuel

Mark 7

Mark 7 Evolution Manuel utilisateur

Husky

Husky HyPET Manuel utilisateur

bora

bora PM-1800 Manuel utilisateur

Siemens

Siemens 8MF1 Series Manuel utilisateur

ABB

ABB HT610965 Manuel utilisateur

ABB

ABB SafeLink Manuel utilisateur

Phoenix

Phoenix PHX-150 Manuel utilisateur

ABB

ABB A165-L32 Manuel utilisateur

ABB

ABB HT842936 Manuel utilisateur

Rioned

Rioned UrbanJet Manuel utilisateur

Hermetica

Hermetica 10 Series Manuel utilisateur

HORNER

HORNER OEE Solution Manuel utilisateur

Hammerhead

Hammerhead HG375 Manuel utilisateur

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instructions d'utilisation

ABB

ABB HT566657 Manuel utilisateur

Webasto

Webasto GSE CAN Manuel utilisateur

ABB

ABB HT614003 Manuel utilisateur