Greenheck FGI Manuel utilisateur

Fabra Hood • Form B 1

Document 471321

Model FGI/FGR Fabra Hood

Form B - Single Section with Birdscreen

Throat length less than or equal to 72 inches

Assembly Instructions

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,

operate or maintain the product described. Protect yourself and others by observing all safety information. Failure

to comply with these instructions will result in voiding of the product warranty and may result in personal injury

and/or property damage.

Standard Assembly

HOOD END ASSEMBLY

(FEMALE RIB)

HOOD RAIL ASSEMBLY

SIDE BIRDSCREEN ASSEMBLY

HOOD SUPPORT ANGLE

BASE ASSEMBLY

END BIRDSCREEN

ASSEMBLY

SIDE BIRDSCREEN

ASSEMBLY

HOOD END ASSEMBLY

(MALE RIB)

HOOD PANEL

Step 1 – Open crates and separate parts

Open the shipping crates and separate the parts according to the size of the unit, refer to Figure 1.

Step 2 – Place BASE ENDS and BASE SIDES

Place the two base ends and the two base sides in their approximate relationship to each other, see Figure 2.

Fasten together using three 1/4-20 fasteners per corner for 5 inch high base and four 1/4-20 fasteners per corner

for 12 inch high base.

NOTE: Fasteners should be hand tightened only until Step 4.

On some units where the difference between the hood width and throat width is greater than 32 inches, a

reinforcing plate is required in the corners of the base, refer to Figure 2, Detail A.

Figure 1

BASE END

BASE SIDE

REINFORCING PLATE

DETAIL A

BASE END

BASE SIDE

Figure 2

IMPORTANT: For high wind rated hoods,

follow assembly instructions starting on page 5.

Fabra Hood • Form B2®

Step 3 – Attach HOOD BASE ENDS to HOOD BASE SIDES

Attach the hood support angle to the base assembly, using four 1/4-20 fasteners per angle, see Figure 3, Detail B.

On some units, two diagonal braces come pre-attached to the hood support angle. Fasten the loose end of the

diagonal braces to the base assembly, using one 1/4-20 fastener per diagonal brace. See Figure 3, Detail C.

BASE

ASSEMBLY

HOOD SUPPORT

ANGLE

DETAIL B

BASE

ASSEMBLY

HOOD SUPPORT

ANGLE

DETAIL C

DIAGONAL

BRACE

Step 4 – Tighten fasteners and caulk all inside corners

Tighten all fasteners. Caulk all inside corners where the base sections come together. At this point, the base may be

lifted onto the roof curb before proceeding with further assembly.

Step 5 – Attach SIDE BIRDSCREEN ASSEMBLY to HOOD SUPPORT ANGLE

Attach the side bird screen assembly to the hood support angle and base assembly using four 1/4-20 x 1 inch

fasteners per screen assembly, see Figure 4.

SIDE BIRDSCREEN

ASSEMBLY

SIDE BIRDSCREEN

ASSEMBLY

BASE ASSEMBLY HOOD SUPPORT

ANGLE

Figure 4

Figure 3

Fabra Hood • Form B 3

END BIRDSCREEN

ASSEMBLY

END BIRDSCREEN

ASSEMBLY

SIDE BIRDSCREEN

FRAME EXTENSION

END BIRDSCREEN

ASSEMBLY

SIDE BIRDSCREEN

ASSEMBLY

BIRDSCREEN

CLIP

DETAIL D

VIEWED FROM UNDER SIDE

Figure 5

Step 6 – Install END BIRDSCREEN ASSEMBLY

Install the end birdscreen assembly, refer to Figure 5. Turn the birdscreen clips (which are pre-assembled to the end

birdscreen assembly) so that two are under the side birdscreen frame extension and the other two are under the

hood support angle. See Figure 5, Detail D.

NOTE: Loosen and tighten the birdscreen clip as necessary.

Step 7 – Attach HOOD RAIL ASSEMBLY to HOOD SUPPORT ANGLES

Attach the hood rail assembly to the hood support angles, using 3/8 x 3/4 inch bolt with 3/8 inch Nyloc nut at each

attachment point, see Figure 6.

NOTE: Fasteners should be hand tightened only until Step 9.

HOOD RAIL

ASSEMBLY

NYLOC NUT

HOOD SUPPORT

ANGLE

HOOD RAIL

ASSEMBLY

HOOD SUPPORT

ANGLE

Figure 6

Fabra Hood • Form B4®

Step 8 – Assemble HOOD PANELS to HOOD RAIL ASSEMBLY

Assemble hood panels to hood rail assembly. The hood end assembly with the “male rib” is to be installed ﬁrst, see

Figure 7, Detail E. Place the remaining hood panels in place, interlocking panels as you go, see Detail E. Secure each

hood panel to the hood rail assembly as it is put in place, using four 12 x 3/8 inch sheet metal screws with sealing

washers per hood panel. The hood end assembly with the “female rib” is to be installed last.

NOTE: Hoods over 9 feet wide are supplied with special hood clips. See Detail F. hood panels have predrilled holes

for hood clip installation. Install clips as hood panels are being put in place, using one 12 x 5/8 inch sheet metal

screw with sealing washer per hood clip. To install clips in the last panel, leave the end birdscreen assembly out to

provide access to the underside of the hood. The end birdscreen assembly can be easily replaced after the hood is

completely assembled.

Step 9 – Tighten fasteners

Tighten all pivot bracket fasteners. NOTE: There may be extra fasteners.

HOOD RAIL

ASSEMBLY

HOOD PANEL

HOOD END ASSEMBLY

(MALE RIB)

HOOD RAIL

ASSEMBLY

MALE RIB

DETAIL E

FEMALE RIB

DETAIL F

HOOD PANEL

(MALE RIB)

NO. 12 x 5/8 SHEET METAL SCREW

WITH SEALING WASHER HOOD PANEL

(FEMALE RIB) MALE RIB FEMALE RIB

HOOD CLIP

Figure 7

Fabra Hood • Form B 5

High Wind Assembly

Step 1 – Open crates and separate parts

Open the shipping crates and separate the parts according to the size of the unit, refer back to Figure 1, page 1.

Step 2 – Place BASE ENDS and BASE SIDES

Place the two base ends and the two base sides in their approximate relationship to each other, see Figure 2. Fasten

together using three 1/4-20 fasteners per corner for 5 inch high base and four 1/4-20 fasteners per corner for 12 inch

high base.

NOTE: Fasteners should be hand tightened only until Step 4.

On some units where the difference between the hood width and throat width is greater than 32 inches, a reinforcing

plate is required in the corners of the base. Refer to Figure 2, Detail A.

BASE END

BASE SIDE

REINFORCING PLATE

DETAIL A

BASE END

BASE SIDE

Step 3 – Attach HOOD BASE ENDS to HOOD BASE SIDES

Attach the hood support angle to the base assembly, using four 1/4-20 fasteners per angle, see Figure 3, Detail B.

On some units, two diagonal braces come pre-attached to the hood support angle. Fasten the loose end of the

diagonal braces to the base assembly, using one 1/4-20 fastener per diagonal brace. See Figure 3, Detail C.

BASE

ASSEMBLY

HOOD SUPPORT

ANGLE

DETAIL B

BASE

ASSEMBLY

HOOD SUPPORT

ANGLE

DETAIL C

DIAGONAL

BRACE

Step 4 – Tighten fasteners and caulk all inside corners

Tighten all fasteners. Caulk all inside corners where the base sections come together.

NOTE: Depending on the size of the hood it may be easier to assemble unit on the ground and lift to the roof

assembled. This is due to the self tapping screws that need to be fastened down the center of the hood.

IMPORTANT: Do not climb on top of hood to fasten screws in the center of the hood.

Figure 2

Figure 3

Fabra Hood • Form B6®

Step 5 – Attach SIDE BIRDSCREEN ASSEMBLY TO HOOD SUPPORT ANGLE

Attach the side bird screen assembly to the hood support angle and base assembly using four 1/4-20 x 1 inch

fasteners per screen assembly, see Figure 4.

SIDE BIRDSCREEN

ASSEMBLY

SIDE BIRDSCREEN

ASSEMBLY

BASE ASSEMBLY HOOD SUPPORT

ANGLE

Step – 6 Install END BIRDSCREEN ASSEMBLY

Install the end birdscreen assembly, refer to Figure 5. Turn the birdscreen clips (which are pre-assembled to the end

birdscreen assembly) so that two are under the side birdscreen frame extension and the other two are under the

hood support angle. See Figure 5, Detail D.

NOTE: Loosen and tighten the birdscreen clip as necessary.

END BIRDSCREEN

ASSEMBLY

END BIRDSCREEN

ASSEMBLY

SIDE BIRDSCREEN

FRAME EXTENSION

END BIRDSCREEN

ASSEMBLY

SIDE BIRDSCREEN

ASSEMBLY

BIRDSCREEN

CLIP

DETAIL D

VIEWED FROM UNDER SIDE

Figure 4

Figure 5

Fabra Hood • Form B 7

Step – 7 HOOD RAIL ASSEMBLY

NOTE: For easier assembly and lifting elevate hood rail assembly on blocks.

Lay out hood rail assembly and hood end angles, see Figure 6. Install thread cutters (hardware kit # 415041 - 5/16-

18 x 1 in.) from underneath, ﬁrst through hood end angles and second hood rail assembly.

NOTE: Use a builders square to ensure the corners of the frame are as close to 90º as possible.

5/16 -18 x 1 in.

THREAD CUTTER

5/16 -18 x 1 in.

THREAD CUTTER

5/16 -18 x 1 in.

THREAD CUTTER

5/16 -18 x 1 in.

THREAD CUTTER

USE PROVIDED

HARDWARE KIT # 415041 HOOD END ANGLE

HOOD RAIL ASSEMBLY

Step 8 – Install HAT CHANNEL

Place diagonal end panel supports with the formed angle running the length of the part facing out and slots next

to hat channel. Fasten diagonals with whiz nut (hardware kit # 415456). Leave wiz nuts snug and DO NOT tighten.

Lift hat channel into place. The diagonals will support the hat channel as it is being installed. Use thread cutters

(hardware kit # 415456) to attach the hat channel to the diagonal end panel supports. Tighten wiz nuts.

5/16 -18 in. WHIZ NUT

HAT CHANNEL

5/16 -18 x 1 in.

THREAD CUTTER (BOTH SIDES)

USE PROVIDED HARDWARE KIT

# 415041 AND 415456

5/16 -18 in. WHIZ NUT

5/16 -18 x 1 in.

THREAD CUTTER (BOTH SIDES)

5/16 -18 in. WHIZ NUT

DIAGONAL END PANEL SUPPORT

NOTE: Adjustment of the hat channel may be needed. Ensure there is no more than an 1/8 inch gap between the hat

channel and hood panel.

Figure 6

Figure 7

Fabra Hood • Form B8®

Step 9 – Install HOOD END PANEL (MALE RIB)

Lift the hood end panel (male rib) into place. Use the 1/4-20 x 1 thread rolling screws with washer (hardware kit #

417119) to attach hood end panel to the diagonal end panel supports at the holes in the hood end panel that line will

line up holes in the diagonal end panel supports.

Use four #12-14 x 1 inch self-tapping screws (hardware kit # 415450) to attach the hood panel to the hat channel.

Use four #12-11 x 5/8 sheet metal screws (hardware kit # 417467) to attach the hood panel to the hood rail

assembly.

HOOD PANEL/END PANEL

ASSEMBLY

NO. 12-14 x 1 in.

SELF TAPPING SCREW

NO. 12-11 5/8 in.

SHEET METAL SCREW

NO. 12-11 5/8 in.

SHEET METAL SCREW

1/4 -20 x 1 in.

THREAD ROLLING SCREW WITH WASHER

USE PROVIDED HARDWARE KIT

# 415180 AND 415450

Figure 8

Fabra Hood • Form B 9

Step 10 – Install HOOD PANELS to HOOD RAIL ASSEMBLY

Place the next hood panel by interlocking each panel as shown in Figure 7, Detail E. Secure each hood panel to

the hood rail assembly as it is put in place, using four #12-14 x 1 inch self-tapping screws (hardware kit # 415450)

to attach the hood panel to the hat channel. Use four #12-11 x 5/8 sheet metal screws (hardware kit # 417467) to

attach the hood panel to the hood rail assembly. Using quantity 10 sheet metal screws (hardware kit # 416900) with

sealing washers per hood panel. Place the remaining hood panels in place with the hood end assembly with the

female rib is to be installed last as shown in step 9.

IMPORTANT: Do not drive sheet metal screws all the way through both sides of the ribs as this could allow water to

leak through the hood. Screws are to fasten only the ﬁrst 2 layers of the rib joint.

1/4 -20 x 1 in.

THREAD ROLLING SCREW WITH WASHER

NO. 12 -14 x 1 in.

SELF TAPPING SCREW (QTY OF 10 PER RIB)

USE PROVIDED HARDWARE KIT

# 415450 AND 417119

Step 11 – Lift HOOD ASSEMBLY onto HOOD BASE

Lift completed hood assembly onto the hood base and attach the hood assembly to the hood support angles, using

3/8 x 3/4 inch bolt with 3/8 inch Nyloc nut at each attachment point.

Step 12 – Tighten fasteners

Tighten all pivot bracket fasteners.

NOTE: There may be extra fasteners.

Figure 9

Fabra Hood • Form B10 ®

Autres manuels pour FGI

Ce manuel convient aux modèles suivants

Autres manuels Greenheck hotte de ventilation

Greenheck

Greenheck Steel Airfoil Blades OFSD-311 Manuel utilisateur

Greenheck

Greenheck Vektor-M Compact ERS Manuel utilisateur

Greenheck

Greenheck BR-30 Series Manuel utilisateur

Greenheck

Greenheck Ductmate 35 Manuel utilisateur

Greenheck

Greenheck Steel Airfoil Blades SMD-301M Manuel utilisateur

Greenheck

Greenheck EM-30 Series Manuel utilisateur

Greenheck

Greenheck DFD-150X series Manuel utilisateur

Greenheck

Greenheck UL 762 Manuel du propriétaire

Greenheck

Greenheck SEFSD Series Manuel utilisateur

Greenheck

Greenheck Smoke Dampers SMD-301V Manuel utilisateur

Greenheck

Greenheck Fire Smoke Dampers FSDGB-211 Manuel utilisateur

Greenheck

Greenheck Inline Centrifugal Grease Fan Manuel utilisateur

Greenheck

Greenheck CSP Manuel utilisateur

Greenheck

Greenheck UL 555S Leakage Class II SSSMDR-502 Manuel utilisateur

Greenheck

Greenheck Smoke Dampers SMD-401 Manuel utilisateur

Greenheck

Greenheck H-CUBE. Manuel utilisateur

Greenheck

Greenheck XG-TH Manuel utilisateur

Greenheck

Greenheck Exhaust Fan SMD-302M Manuel utilisateur

Greenheck

Greenheck Steel Airfoil Blades FSD-311V Manuel utilisateur

Greenheck

Greenheck KFD Series Manuel utilisateur

Greenheck

Greenheck TCB Manuel utilisateur

Greenheck

Greenheck 471555 Manuel utilisateur

Greenheck

Greenheck Sleeve Extensions 462103 Manuel du propriétaire

Greenheck

Greenheck Vektor-H Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur