GRAPHTEC midi LOGGER GL240 Manuel utilisateur
GL240
midi LOGGER
Quick Start Guide
604249021 GL240-UM-851
Contents
Thank you for choose the midi LOGGER GL240.
This Quick Start Guide describes the basic operations.
Please refer to the manual (PDF) in the CD-ROM for more information.
Nomenclature ……………………………………………………… 2
Connection Procedures ……………………………………………3
Precautions to Observe When Performing Measurement
………5
Descriptions of the Control Panel Keys ………………………… 6
Descriptions of the Menu Screens ……………………………… 9
Measurement Procedure…………………………………………10
1. Preparations :
How to Make the Preparations Required for Data Capture
…………………
10
2. Setup : How to Make the Settings ……………………………………………11
3.
Data Capture : How to Capture Data
…………………………………………14
4.
Data Replay : How to Replay Captured Data
………………………………15
Convenient Functions …………………………………………… 16
Trigger Functions to Control Data Capture Start/Stop Operations
………… 16
Span, Position and Trace Functions to Adjust the Waveform Display
……… 18
Specifications …………………………………………………… 19
Standard Specifications ………………………………………………………… 19
External Input/Output Functions
…………………………………………………19
Specification of input section …………………………………………………… 20
Installation Guide
…………………………………………………21
After unpacking, check the GL240's Exterior to make sure that
there are crack or other damage before use.
• Quick Start Guide : 1 • Ferrite core: 1 • CD-ROM : 1
• AC cable/AC adapter : 1
Checking the Outer Casing
Checking the Accessories
1
Nomenclature
Bottom Panel
Top Panel
Input/out put cable for GL
(Cable is the option B-513)
Humidity sensor
(Option: when using the B-530)
USB interface terminal
Operation status LED
SD CARD2
• POWER
• START
• CHARGE
Control panel keys
External input/output terminals
• LOGIC/PULSE
• EXT TRIG/SAMPLE
• ALARM
GND terminal
Power jack for humidity sensor
Analog signal input terminals
AC adapter jack
Two battery pack can be installed
(Battery pack is the option B-569)
Power switch
Tilt foot
Battery cover
Label
Wireless LAN
connection terminal
Wireless unit
(Option: when using the B-568)
2
Connection Procedures
Orange with red dotted line : 1
Orange with black dotted line : 2
Grey with red dotted line : 3
Grey with black dotted line : 4
White with red dotted line : 1
White with black dotted line : 2
Yellow with red dotted line : 3
Yellow with black dotted line : 4
Pink with red dotted line : Trigger input/
external sampling input
Shielded GND
Logic/pulse
input
Alarm output
< Signal assignment >
Pink with black dotted line
Connecting the AC Adapter
Connect the DC output of the AC adapter to the
connector indicated as "DC LINE" on the GL240.
Connecting the Grounding Cable
Use a flathead screwdriver to push the button above
the GND terminal while connecting the grounding
cable to the GL240. Connect the other end of the
cable to ground.
Making Connections to the Analog Input Terminals
CAUTION: Connect wires to the specified channel, the channel number is shown on top of the terminal block.
Making Connections to the External Input/Output Terminals
(For logic/pulse input, alarm output, trigger input, external sampling pulse input)
CH 10 9 8 7 6 5 4 3 2 1
3
+
-
Thermocouple input
Compensation wire is
used if it is required.
+
-
Shunt resister
Ex: The current is converted to the voltage in the
shunt register.
For 4 to 20mA current input, installing 250 ohms
(0.1%) resister for converting 1 to 5V.
Note: 250 Ω shunt register is the option B-551.
Current input
+
-
DC voltage input
Voltage input
A-type connector B-type connector
Internal memory
Mounting of the SD CARD 2
CAUTION: The SD memory card is unlocked by pushing gently the SD memory card. Then, remove the SD
memory card.
When the optional wireless LAN unit is installed, the SD memory card cannot be mounted.
The POWER LED blinks while accessing to the SD memory card.
Connection of the USB cable
This midi LOGGER complies with the EMC Directive in the state when the supplied ferrite core is attached to the
USB cable.
When connecting to the PC with
the USB cable, attach the supplied
ferrite core to the USB cable as
shown in the following figure.
Using the cable with A-type and B-type connectors,
connect between the midi LOGGER and PC.
< How to remove >
(1) The SD memory card is
unlocked by pushing
gently the SD memory
card. Then, remove the
SD memory card.
USB cable
Ferrite core (Supplied)
< How to mount >
(1) Open the protective cover of
SD CARD 2.
(2) Push the SD memory card
until it clicks and is locked.
* Make sure that the
SD memory card is
not locked.
4
• The internal memory is displayed as the SD1 or SD CARD1
• The internal memory is not removable.
Precautions to Observe When Performing Measurement
Maximum input voltage
If a voltage exceeding the specified value is input, the semiconductor relay in the
input section will be damaged. Never input a voltage exceeding the specified value
even for a moment.
< Between +/– terminals(A) >
• Maximum input voltage: 60Vp-p (Range of 20mV to 1V)
110Vp-p (Range of 2V to 100V)
< Between input terminal/input terminal (B) >
• Maximum input voltage: 60Vp-p
• Withstand voltage: 350 Vp-p at 1 minute
< Between input terminal/GND (C) >
• Maximum input voltage: 60Vp-p
• Withstand voltage: 350 Vp-p at 1 minute
Warming-up
GL240 requests to have approximately 30 minutes warm-up in order to have the
specified performance.
Unused channels
The analog input section has high impedance.
If it is open, measured value may vary due to noise.
In such a case, set to "Off" unused channels in the AMP setting menu or short the +
and – terminals.
Noise countermeasures
If measured values fluctuate due to extraneous noise, conduct the following
countermeasures.(Results may differ according to noise type.)
Ex 1 : Connect the GL240's GND to ground.
Ex 2 : Connect GL240's GND to measurement object's GND.
Ex 3 : Operate GL240 with batteries (Option: B-569).
Ex 4 : In the AMP settings menu, set filter to any setting other than "OFF".
Ex 5: Set the sampling interval which enables GL240’s digital filter (see table below).
Number of Measuring
Channels *1
1 chahnnel or less
5 chahnnels or less
2 chahnnels or less
10 chahnnels or less
10 msec or slower *2
50 msec or slower *2
20 msec or slower *2
100 msec or slower
50 msec or slower
250 msec or slower
125 msec or slower
500 msec or slower
Allowed Sampling
Interval
Sampling Interval which
enables Digital Filter
*1 Number of Measuring Channels is the number of channels in which input settings are
NOT set to “OFF” .
*2
Temperature cannot be measured when the sampling interval is set to 10 ms/20 ms or 50 ms.
5
Descriptions of the Control Panel Keys
Press the [TIME/DIV] key to change the time axis display range on the waveform
screen.
2.TIME/DIV
This key enables SPAN, POSITION, and TRACE settings to be made
independently fo reach channel. Each time this key is pressed, the display mode
changes in the sequence shown below. Use the and keys to select the
channel, and the and keys to change the setting values.
1.SPAN/POSI/TRACE
Points to Remember
Displays digital values (default).
Used to change span settings (change the waveform amplitude).
Used to change position settings (adjust the upper and lower values
of the waveform).
Used to change trace settings (set the waveform display to On or Off).
* If the [QUIT] key is pressed when the GL240 is in the SPAN, POSITION, or
TRACE mode, the display returns to MONITOR mode.
6
(4) QUIT (3) MENU
(5) DIRECTION KEYS
(6) ENTER
(10) REVIEW (9) DISPLAY
(11) FILE/GROUP
(2) TIME/DIV
(12) CURSOR (ALARM CLEAR) (8) START/STOP (USB DRIVE MODE)
(7) FAST FORWARD (KEY LOCK)
(1) SPAN/POSI/TRACE
+ + ENTER
Password setting
MONITOR
SPAN
POSITION
TRACE
7
Press the [MENU] key to open a setup menu. Each time this key is pressed, the
setup screen tabs change in the sequence shown below.
3.MENU
Press the [QUIT] key to cancel the settings and return them to their default status.
If the device is in the Remote (Key Lock) status that the device is operated by the
computer via the interface, press this key to return the device to the normal
operating status (Local).
4.QUIT (LOCAL)
These keys are used to select menu setup items, to make span settings in the digital
display area, to move the cursors during a data replay operation, and so forth.
5.Keys (DIRECTION KEYS)
Press the [ENTER] key to enter the settings made in the setup menus, and to
confirm your settings.
6.ENTER
Used to move the cursor at high speed during replaying or change the operation
mode in the file box. Hold down both keys simultaneously for at least two seconds
to enable key lock status.
To cancel key lock status, press them again for at least two seconds.
The key lock status can be confirmed in whether or not the key lock lamp on the
monitor is lit in yellow.
* Pressing these keys simultaneously with the key + ENTER + key enables password protection
for the key lock operation.
7.Keys (KEY LOCK)
Points to Remember
•AMP Settings
Used to set the input, range, filter and other settings.
•Data Capture Settings
Used to set settings such as the sampling interval, data capture
destination, and calculations during data capture.
•Trigger Settings
Used to specify data capture start and stop conditions, and alarm
conditions.
•Interface Settings
Used to set the USB ID.
•Wireless LAN setting
(displayed when the option is installed)
Used to set the connection to the wireless LAN after the wireless
unit is installed.
•Other Settings
Used to set the screen brightness, background color, and language,
etc.
AMP
DAT (DATA)
TRG (TRIG)
I/F
LAN
OTH (OTHR)
Press the [START/STOP] key to perform start and stop of a data capture while the
GL240 is in the Free Running status.
If this key is held down while the power to the GL240 is turned on, the GL240 is
switched the USB to the Drive Mode.
* For more information about the Drive Mode of the USB, refer to the User's Manual in the supplied
CD.
8.START/STOP (USB DRIVE MODE)
Press the [REVIEW] key to replay captured data. If the GL240 is in the Free
Running status, data files that have already been captured are replayed. If the
GL240 is still capturing data, the data is replayed in a 2-screen format.
* A data replay operation will not be performed if data has not been captured.
10.REVIEW
Press the [CURSOR] key to switch between the A and B cursors during a data
replay operation.
If the Alarm setting has been specified as "Alarm Hold", press this key to clear the
alarm.
The alarm settings are made in the "TRIG" menu.
12.CURSOR (ALARM CLEAR)
It is used to operate the internal memory (SD1) and SD memory card (SD2), or
replace the SD memory card (SD2).
11.FILE
Press the [DISPLAY] key
9.DISPLAY
Points to Remember
•Waveform + Digital
This is the default screen when the GL240 is turned on,
and both waveforms and digital values are displayed.The
screen settings can also be changed by using the
[SPAN/POSI/TRACE] key.
•Expanded Waveform
Displays waveforms only.
* For more information, refer to the User's Manual in the
supplied CD.
•Digital + Calc
Displays large-size digital values and two types of
calculation processing results. The calculation settings are
made in the "DATA" menu.
Use the key or key to switch digital display
modes.
Waveform + Digital
Expanded Waveform
Digital + Calc
8
Autres manuels pour midi LOGGER GL240
4
Table des matières
Autres manuels GRAPHTEC Enregistreur de données
GRAPHTEC
GRAPHTEC midi LOGGER HV Manuel utilisateur
GRAPHTEC
GRAPHTEC GL840 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL500 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL900 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL980 Manuel utilisateur
GRAPHTEC
GRAPHTEC midi LOGGER GL240 Manuel utilisateur
GRAPHTEC
GRAPHTEC midi LOGGER GL800 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL820 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL980 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL820-UM-851 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL450 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL820 Manuel utilisateur
GRAPHTEC
GRAPHTEC midi LOGGER GL240 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL840 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL450 Manuel utilisateur
GRAPHTEC
GRAPHTEC gl200 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL2000 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL350 Manuel utilisateur
GRAPHTEC
GRAPHTEC midi LOGGER GL240 Manuel utilisateur
GRAPHTEC
GRAPHTEC GL100 Manuel utilisateur
