Grant SpiraPod Manuel utilisateur

Grant SpiraPod Outdoor Enclosure

For Grant Spira Wood Pellet Boilers

Installation Instructions

Part No. DOC.46 Rev.04 19/05/17

EC Declaration of Conformity

In accordance with BS EN ISO/IEC 17050-1:2004

We Grant Engineering (IRL)

Of Crinkle

Birr

County Offaly

Ireland

Telephone: 057 912 0089

Fax: 057 912 1060

Email: info@grantengineering.ie

Website: www.grantengineering.ie

Declare that

Equipment: Floor Standing External Enclosure with integral Wood Pellet Hopper

Model Name/Number: Grant SpiraPod

In accordance with the following EC Directives:

2006/42/EC Conforms with the requirements of the Machinery Directive.

2006/95/EC Conforms with the safety objectives of the Low Voltage Directive and it’s

amending Directives

2004/108/EC Conforms with the essential protection requirements of the

Electromagnetic Compatibility Directive and it’s amending Directives

Has been designed and manufactured to the following Specifications:

EN60335-1:2012 Household and similar electrical appliances. Safety –General

requirements.

EN60335-2-102:2006+A1:2010 Household and similar electrical appliances. Safety. Particular

requirements for gas, oil and sold fuel burning appliances having

electrical connections.

EN55014-1:2006 Electromagnetic Compatibility. Requirements for household appliances.

EN303-5:2012 Heating Boilers for solid fuels. Manually or automatically stoked.

Nominal heat output up to 500kW.

MCS008 Product Certification scheme requirements - Biomass

Important Note for Installers

After installing the boiler leave these Installation Instructions with the appliance. Also leave both the

Installation and Servicing Instructions and the User Instructions (supplied with the boiler) with the

householder.

This appliance is deemed a controlled service and specific regional statutory requirements may be

applicable.

Contents

Section Page

1. Introduction 4

2. Technical Data 6

3. Installation 8

4. Pipework 13

5. Condensate Disposal 14

6. Sealed System Kit 15

7. Flue System 20

8. Electrical 24

9. SpiraVac System 26

10. Commissioning 27

11. Servicing 29

12. Spare Parts 30

13. Health & Safety Information 30

14. Guarantee 30

The following special text formats are used in this manual for the purposes listed below;

WARNING

Warning of possible human injury as a consequence of not following the instructions in the “warning”

CAUTION

Caution concerning likely damage to equipment or tools as a consequence of not following the

instructions in the “Caution”

NOTE

Used for emphasis or information not directly concerned with the surrounding text but of importance to

the reader.

1. Introduction

1.1 Grant SpiraPod Outdoor Enclosure

Figure 1-1: Front/right side view of Grant SpiraPod

1.2 Description

The Grant SpiraPod is a weatherproof housing for the external installation of the Standard Grant Spira

5/18, 6/26 or 9/36 wood pellet burning condensing boilers. It is constructed from 1.0mm, 1.5mm, and

2mm thick Galvanised steel, finished with a polyester powder coating in ‘Grant Grey’.

It is supplied fully assembled, with the pellet hopper and pellet auger fitted, ready for the installation of the

Grant Spira boiler. The integral pellet hopper has a capacity is 180 kg.

The Grant SpiraPod incorporates several doors and covers to allow easy access to the boiler for the

installation commissioning and servicing of the boiler contained within.

1.3 Pellet Hopper

The Grant SpiraPod pellet hopper has a capacity of approximately 180 kg. This is accessed by lifting the

hinged hopper lid on the top of the SpiraPod so that pellets can be tipped into the hopper by the user.

The hinged hopper lid is fitted with two gas struts to assist with opening and closing. This lid MUST BE

CLOSED after filling to prevent any water/rain entry

The hopper is fitted with a contents sensor. This detects when the level of pellets in the hopper falls to a

pre-set minimum level (approximately 20 kg) and, if a bulk pellet store is used, triggers the operation of

either a bulk store auger, or vacuum system, to deliver pellets from the bulk store. If no bulk store is used,

the contents sensor will stop the burner operating when the minimum pellet level is reached.

Topping up the hopper with more pellets will automatically operate the contents sensor and the burner

will restart (if there is a demand for the boiler to run). The hopper must be topped up with a further 10kg

(total of at least 30kg) of pellets to restart the boiler.

The electrical connection to the boiler is made to the 4-way electrical plug on the factory-fitted ‘flying lead’

from the Spirapod wiring centre, located at the front of the pellet hopper. Refer to both Section 8 of these

Installation Instructions and Section 8 of the Spira Installation & Servicing Instructions for electrical

connection details.

1.4 Flue System

The design of the Grant SpiraPod allows for the standard Grant Biomass flue system to be used. Refer to

Section 7 of these Installation Instructions and also Section 7 of the Installation & Servicing Instructions

supplied with the boiler.

1.5 Frost Protection

The Grant SpiraPod is supplied with a factory fitted frost protection thermostat. This is located inside the

SpiraPod enclosure on the rear of the SpiraPod wiring centre (located at the front of the pellet hopper).

Refer to Figure 1-2. It is pre-wired to the boiler SpiraPod electrical wiring centre and factory set to 2°C.

Grant recommends the use of a Pipe Thermostat (not supplied) in conjunction with the Frost thermostat

to avoid unnecessary and wasteful overheating of the property. This pipe thermostat should be located

on the boiler return pipe and set to operate at 25°C. Refer to the Section 8 of the Installation & Servicing

Instructions supplied with the boiler for details of the pipe thermostat electrical connections.

For total system protection against freezing, particularly during extended periods without electrical power,

Grant recommends the use of a combined heating system antifreeze and corrosion inhibitor, used in

accordance with the manufacturer's instructions.

1.6 Access

The SpiraPod enclosure is fitted with the following means of access:

A pair of hinged doors (with lockable door catch*) at the front –for access to the boiler for

routine cleaning (emptying the ash pan), access to boiler/burner controls and the Vacuum

system controls (if fitted).

A hinged hopper lid (with lockable door catch*) on the top left side –to allow pellets to be tipped

into the hopper by the user.

A hinged cover panel (with internal catch) on the top right side –to allow access to the top of the

boiler for Commissioning and Servicing.

A removable door panel (with lockable door catch*) at the rear –to allow access to the electrical

wiring centre and rear of boiler for commissioning and servicing.

* These door catches can be fitted with a small padlock (not supplied) if required.

To unlock and open any of the above, unlock/remove the padlock (if fitted). Rotate the knob of the catch

clockwise to unlatch and open the front door or pellet hopper lid. On the rear access door panel rotate

the knob anticlockwise to unlatch and remove. Close and lock the door, lid or panel using the reverse of

the above procedure.

Figure 1-2: Location of frost thermostat

Frost Thermostat

Wiring Centre

2. Technical Data

2.1 Technical Specification

Weight –excluding boiler (empty pellet hopper)

200 kg

Weight –excluding boiler (full pellet hopper)

380 kg

Weight –full pellet hopper and Spira 5-18 and 6-26 boiler (full)

663 kg

Weight –full pellet hopper and Spira 9-36 boiler (full)

702 kg

For further technical data refer to Section 2 of the Installation & Servicing Instructions supplied with the

Spira boiler.

2.2 Pump Specification (Sealed System Kits only)

Make and Model

Wilo Yonos PARA RS 15/7.0 RKC FS 130 12

Construction

Pump housing

Cast iron (with cataphorisis treatment)

Impeller

PP composite with GF 40%

Pump Shaft

Stainless Steel

Bearing

Carbon, metal impregnated

Protection Class

IPx4D

Insulation Class

Motor Protection

Integrated

Performance

Max Delivery Head

7.2m @ Q = 0 m3 /h

Max Volume Flow

3.3 0 m3 /h

Minimum Suction Head @ 50/95°C

0.5/4.5m

Power Consumption @ 1 –230V

3 –45W

Nominal Motor Power

37W

Current @ 1 –230V

0.028 –0.44 A

EEI

≤0.20

Speed

800 –4650 rpm

Settings

∆P-variable (1 –7m head) and Constant Speed (I, II and III)

Application

Maximum Static Pressure

PN6

Temperature Range @ Max Ambient

Temperatures

Max Ambient temperature 57°C: 0 to 95°C

Max Ambient temperature 59°C: 0 to 90°C

Max Ambient temperature 67°C: 0 to 70°C

Approved Fluids

Heating Water

Water/Glycol –Max 1:1 (above 20% check pumping data)

Energy Efficiency Index

The Grant Spira sealed system kits are supplied with a Wilo Yonos PARA circulating pump that complies

with the Energy Related Products (ErP) Directive requirement that all glandless circulating pumps have an

Energy Efficiency Index (EEI) of not more than 0.23 from the 1st August 2015.

2.3 Dimensions

Figure 2-1. SpiraPod overall dimensions

3. Installation Information

3.1 Regulations

The Installation of a Grant SpiraPod and Spira wood pellet boiler must be in accordance with the Building

Regulations and any local Byelaws, Water Regulations, British Standards and any other relevant

legislation. Refer to Section 4 of the boiler Installation & Servicing Instructions boiler for further details.

Refer to Local Building regulations for minimum distances between the SpiraPod and combustible

materials.

Check with the Local Authority regarding the possible need for Planning Permission for an external boiler.

3.2 Boiler location

The Grant SpiraPod can be installed either against the building or 'free standing' some distance away

from the building. Refer to Figures 7-4 and 7-5.

If the ‘free standing’ option is chosen, then the boiler flue system must be at least 2300mm away from

any buildings or structure that are higher than the flue outlet. See Figure 7-4. If this distance cannot be

achieved, then the SpiraPod will have to be located with the right hand side close to or against the

building and the flue system extended such that the terminal is above the eaves of the roof. Refer to

Figure 7-5.

The Grant SpiraPod must be positioned such that sufficient clearance is provided for maintenance,

servicing and filling the pellet hopper. In particular the following minimum clearances are required around

the SpiraPod:

Rear: 800mm (to remove panel and access to rear of boiler/hopper)

Front:1500mm (to open doors and install/commission/service boiler)

Pellet hopper side: 600mm (to access pellet hopper and open pellet hopper lid)

3.3 Base

The Grant SpiraPod must stand on a solid, level non-combustible surface capable of supporting both the

weight of the boiler when full of water, and the weight of the enclosure/pellet hopper when full of pellets.

Refer to Section 2 of these Installation Instructions for weights.

Grant recommends a prepared concrete standing (at least 150mm thick) with a smooth finish on the top

extending beyond the enclosure base at least 100mm all around.

3.4 Installation of SpiraPod

The Grant SpiraPod is supplied fully assembled, with the pellet hopper and pellet auger fitted, ready for

the installation of the Grant Spira boiler.

Position the SpiraPod in the required position/orientation on the concrete base and secure it to the

concrete, using suitable fixings (e.g. Rawlbolts or similar) through the two holes provided in the base at

the front of the enclosure. Refer to Figure 3-1.

Eight triangular steel shims are supplied with the boiler. These can be fitted under one or more corners,

as and when necessary, to level the SpiraPod (BEFORE securing it to the concrete base).

3.5 Installation of the Spira boiler

With both the front doors open and the rear access panel removed:

Remove the corner bracket from the top right hand corner of the front door opening. Refer to

Figure 3-2. Keep this bracket, and the four fixing screws, as this will need to be replaced once

the boiler is installed.

IMPORTANT

BEFORE fitting the boiler into the SpiraPod, It is essential that the pellet auger is rotated, as detailed

below, to ensure that the end of the auger outlet does not come into contact with the side of the boiler

during the installation process.

The auger is not fastened to the pellet hopper but is held in position by a bracket that fits over the

auger housing. Refer to Figure 3-3.

To rotate the auger; grasp the auger motor and auger outlet and carefully pull the auger out by

about 50mm until the auger mounting bracket is clear of the auger housing. Refer to Figure 3-4.

Figure 3-2. Top right corner bracket

Figure 3-3. Auger mounting bracket

Figure 3-1. Spirapod base

Rear stop rail

Guide rail

Fixing hole

Removable

section of

guide rail

Guide rail

Auger mounting

bracket

Corner bracket

Auger housing

Fixing hole

Rotate the auger clockwise until the auger outlet is facing directly downwards. Carefully allow the

auger to fall back into the auger housing until the bracket rests on the end of the auger housing

with the outlet still pointing directly downwards. Refer to Figure 3-5.

Remove the burner from the combustion chamber door of the boiler, taking care not to damage

the white gasket between the door and burner. Refer to Section 11.7 of the Installation &

Servicing Instructions supplied with the boiler for guidance on removing the burner.

Lightly lubricate the base area (using WD40 or similar lubricant). Do not use washing up liquid, or

anything similar, for this purpose as this may stain the base of the SpiraPod.

Position the boiler inside the SpiraPod, with the combustion chamber door facing forwards, and

align the sides with the two guide rails on the SpiraPod base. Refer to Figure 3-1

Carefully push the boiler towards the back of the SpiraPod enclosure until the rear edge of the

boiler base reaches the stop rail at the back.

NOTE: This process may be easier if a rope or similar (e.g. a lifting strop) is placed around the

base of the boiler and out of through the rear of the enclosure. The boiler can then be

simultaneously pulled and pushed into position against the rear stop rail.

Once in position it is not necessary to secure the boiler down to the base of the SpiraPod

enclosure.

Remove and discard the front section of the left hand guide rails, to allow the boiler combustion

chamber door to fully open. Unscrew and remove the rail fixing screws to remove this section of

guide rail only.

Fit the pellet feed tube to the burner so that the open end faces towards the left. Refer to Section

4.1.1 of the Installation & Service Instructions supplied with the boiler for details on the fitting of

the pellet feed tube.

Refit burner to the combustion chamber door and reconnect the two plugs from the boiler control

panel. Refer to Section 11.9 of the Installation & Service Instructions supplied with the boiler.

Fit the pellet feed tube thermostat lead onto the thermostat terminals. Refer to Section 10.5 of the

Installation & Service Instructions supplied with the boiler for details on the fitting of the pellet

feed tube thermostat lead.

Figure 3-4. Pull auger out from housing

Figure 3-5. Rotate auger clockwise

Table des matières

Autres manuels Grant Fournitures pour chaudières

Grant

Grant SpiraVac WPVKIT5POD Instructions de montage

Manuels Fournitures pour chaudières populaires d'autres marques

Beretta

Beretta B23 Manuel utilisateur

Fröling

Fröling Lambdatronic S 3200 Manuel utilisateur

CleaverBrooks

CleaverBrooks Hawk 1000 Manuel utilisateur

De Dietrich Thermique

De Dietrich Thermique AD252 Manuel utilisateur

Trane

Trane BAYAIR30CNVENT Instructions de montage

NTI

NTI 83112-1 Manuel utilisateur

TriangleTube

TriangleTube CCRKIT32 Manuel utilisateur

Bosch

Bosch CB 28 Manuel utilisateur

Volt Polska

Volt Polska GREEN BOOST 3000 Manuel utilisateur

Immergas

Immergas 3.031483 Manuel du produit

DeDietrich

DeDietrich EA 92 Manuel utilisateur

AFRISO

AFRISO PrimoBox ACB 910 Fiche technique

Beretta

Beretta CONNECT BASE MIX 1 LE Manuel d'utilisation et d'installation

tado°

tado° Elexia Manuel utilisateur

TriangleTube

TriangleTube PSRKIT84 Manuel utilisateur

Buderus

Buderus Logamax plus GB142-24 Manuel utilisateur

Bosch

Bosch 7738003218 Manuel utilisateur

Immergas

Immergas VICTRIX PRO 35 Manuel utilisateur