Graco T-MAX 506 Manuel

T-MAX™506/657

www.graco.com

STARTUP

STARTUP Spray with Air <= 1.5 mm

Fill material hopper

with pre-mixed texture

material.

Turn pressure control

knop until a steady

stream flows from

material hose. Turn pump OFF.

Turn applicator OFF,

Turn ON/OFF switch

to ON

Lossen nut on bottom

of pump

two to three turns to

relieve pressure

Turn pressure control

to maximum. To spray,

aim applicator with a

distance of 0,5 m to the

wall and open applictor.

To clean a tip clog, turn

applicator OFF, turn Tip 180°

to Clean position, aim in waste

area, turn applicator ON, when

clog clears, turn applictor OFF

and tip in spray postion.

Turn pressure

control off (0).

Point applicator

into hopper.

Turn applicator ON.

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure Relief

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure

Relief

Use different tip size

for different flow

Install filter and tip

extension.

Connect applicator

to material hose.

Add water if thinning is

required. Mix thoroughly.

HDA531

HDA535

HDA541

HDA545

HDA651

HDA661

HDA671

mc03 m

Spray without Air < .25 mm

Srew tip assembley

onto applicator

Fill material hopper with

mixed texture material.

Place material hose in Hopper turn ON/OFF switch to ON Turn

control in the “green” segment, allow material to circulate 30 sec.

Turn pump control to

shut pump off

Screw air hose and valve to applicator.

Connect material hose to gun kit

Turn applicator valve OFF.

Install air nozzle.

Hold applicator over

material hopper and turn

applicator ON.

Turn air compressor ON. Turn pump

control in the “green” area, until

desired material rate is achieved.

Regulate the air valve to

get a good atomization.

To stop spraying,

turn applicator OFF

Quick Operator’s Guide

SETUP

This procedure is for water-base paints and flushing fluids. For solvent-base paints and flushing

fluids (i.e. mineral spirits), you must read Fire and Explosion Hazard in the Operating Instructions.

* check the Graco operations manual delivered with the unit for more details.

WARNING

Turn pump control off (0).

Connect power cord.Connect pump module to hopper cart.

Remove pump plug.

Connect material hose to pump outlet.

PRESSURE RELIEF PROCESS

Turn pump control counter clockwise,

to shut pump off.

Close applictor after pressure release,

close air valve

Scrape material remaining in

hopper into pump to be pumped

from sprayer.

Rotate pump control to

(0) to shut pump off.

Shut OFF air compressor if spraying with air.

Remove applicator from material hose.

Clean applicator.

Rotate pump control

clockwise to start pump.

Rotate pump control to (0) to

shut pump off.

Clean applicator, spray tips and

guard with brush.ON/OFF switch to OFF

Turn pump control

clockwise and pump

unused texture material

from material hopper

and hose.

Run pump until

cleaning ball exits

material hose.Save

cleaning ball. Repeat

it till the water that

comes out is clear.

Insert wet cleaning ball into pump.

Connect material hose to pump outlet.

Clean hardened material

from applicator nozzles

with air nozzle cleaner.

Remove drain plug from Hopper

Clean hopper with water, brush

and sponge, install drain plug. fill

hopper 1/3 with clear water.

GRACO DISTRIBUTION BVBA Industrieterrein Oude Bunders

Slakweidestraat 31 • B-3630 Maasmechelen

Tel: +32 (89) 770 700 • Fax: +32 (89) 770 777

www.graco.com

Graco is certified ISO 9001.

All information, illustrations, and specifications in this document are based on the latest product information

available at the time of publication. The right is reserved to make changes at any time without notice.

CHOOSE THE RIGHT TIP (HDA-XXX)

CLEANUP

XTRA LIGHT LIGHT MEDIUM HEAVY

HDA531 HDA541 HDA651 HDA671

HDA535 HDA545 HDA661 -

VERY FINE - 3MM FINE - 4MM MEDIUM - 6MM MEDIUM HEAVY - 8MM HEAVY - 10MM

248888 248524 248525 248526 248527

Autres manuels pour T-MAX 506

Ce manuel convient aux modèles suivants

Autres manuels Graco Pistolet à peinture

Graco

Graco SaniForce 26C799 Manuel utilisateur

Graco

Graco Fusion CS Series Manuel utilisateur

Graco

Graco 226-161 SERIES"A" Manuel d'utilisation

Graco

Graco TexSpray Compact HP Manuel d'utilisation

Graco

Graco 3A0149C Fiche technique

Graco

Graco 918316 Manuel d'utilisation

Graco

Graco Gmax 7900 Manuel utilisateur

Graco

Graco 918623 A Series Manuel d'utilisation

Graco

Graco ULTRA 1500 Manuel d'utilisation

Graco

Graco 258864 Mode d’emploi

Graco

Graco 245924 Manuel utilisateur

Graco

Graco 311286C Mode d’emploi

Graco

Graco DURON Performance 390 Manuel utilisateur

Graco

Graco GH Series Mode d’emploi

Graco

Graco Spray Station Manuel utilisateur

Graco

Graco Roof Rigs 224483 Manuel d'utilisation

Graco

Graco 237–428 Manuel d'utilisation

Graco

Graco 311321H Guide de démarrage rapide

Graco

Graco HVLP 2500 Manuel

Graco

Graco Glascraft GC-1388G Manuel utilisateur

Graco

Graco GMAX II 3900 Premium Manuel

Graco

Graco H.E.L.P. 1600B Manuel d'utilisation

Graco

Graco Project Painter Plus 257025 Manuel utilisateur

Graco

Graco 231-406, Series A Manuel d'utilisation

Manuels Pistolet à peinture populaires d'autres marques

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuel utilisateur

Binks

Binks SV100 Manuel utilisateur

Fimco

Fimco LG-4-3-1 Manuel utilisateur

AG SPRAY

AG SPRAY FS-ATV-25BL Manuel utilisateur

Nordson

Nordson MicroMax 2 Manuel utilisateur

Bonide

Bonide 051 Manuel d'utilisation

zogics

zogics Z-DAS Manuel utilisateur

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuel utilisateur

Matrix

Matrix SG 650 Manuel utilisateur

Anest Iwata

Anest Iwata SGA-3 Guide de démarrage rapide

paasche

paasche VV Fiche technique

Carlisle

Carlisle DeVilbiss JGA-510 Manuel utilisateur

Gardena

Gardena 11120 Manuel utilisateur

Conrad

Conrad Hobby Airbrush K3 Manuel utilisateur

wiwa

wiwa 14025 R/F Manuel utilisateur

DeVilbiss

DeVilbiss LUNA2i Manuel utilisateur

WAGNER

WAGNER W 125 Manuel utilisateur

My Clean Buddy

My Clean Buddy PW018 Manuel utilisateur