Graco 25D496 Manuel utilisateur

Read Operation manual 3A5725 for complete instructions and warnings.

This guide is not a substitute for reading and understanding all operation manuals and warning labels supplied

with the equipment. It is important that you read and understand all warnings and instructions before operating

this equipment.

Follow the pressure relief procedure

and wear protective equipment including but not limited to protective eye wear.

RUPTURE HAZARD: Over-pressurizing the hopper can result in rupture. To avoid injury, only pressurize hopper

by connecting air supply tube to barbs on hopper and gun.

FAILURE TO FOLLOW ALL WARNINGS CAN RESULT IN SERIOUS INJURY, AMPUTATION OR DEATH.

COMPONENT IDENTIFICATION - 25D496

A. Material Flow Regulator: Pressurizes

the material hopper and adjusts material

flow. Turn counterclockwise to decrease

flow; turn clockwise to increase flow. Push

down to lock; pull up to unlock.

B. Needle Travel Adjustment Knob:

Adjusts the positions of the gun needle in

relation to the spray tip. Turn clockwise to

limit needle travel and reduce material

flow; turn counterclockwise to increase

needle travel and increase flow.

C. Air Flow Valve: Adjusts the amount of

atomizing air that is sent to the spray tip to

control the spray pattern. Turn clockwise to

decrease air flow; turn counterclockwise to

increase air flow.

Quick Start Guide for Pressurized Hopper Gun

For spray application of water-based architectural and texture coatings.

Recommended gun settings for different patterns can be found on page 19 of the Operation manual.

WARNING

SETUP

1: When spraying ceilings, the hopper should be tilted forward. When spraying floors, the hopper should be tilted

backward. 2: Apply grease to o-ring on the gun. 3: Loosen hopper clamp, slide it over the rib and toward the top of the

hopper. Position hopper outlet over the hopper port on the gun and push hopper down as far as it will go. Slide down

hopper clamp and hand tighten. 4: Attach tube from hopper barb to gun barb. 5: Apply grease to hopper o-ring. 6: Fill

hopper with prepared texture material. 7: Assemble lid with four clamps. Evenly tighten all four clamps. If there is a leak

from the lid, adjust the clamp tension. The lid should be tightened evenly on the hopper.

NOTICE

Over-tightening the lid may damage

the hopper and/or hopper lid.

OPERATION

1: Connect one end of air hose to the compressor air outlet fitting and the other end to the gun air inlet fitting. 2: Pull up on

material flow regulator knob to unlock. Completely close the air flow valve by turning the knob clockwise; turn the material

flow regulator to the lowest setting counterclockwise. 3: Turn air compressor power switch ON. Adjust air flow valve and

material flow regulator on hopper gun for desired texture. Push down on the material flow regulator to lock settings.

SPRAY PATTERNS (see page 19 of the Operation manual for nozzle & tip recommendations)

Nozzle Pattern WideTex Pattern

Original Instructions. This manual contains English. MM 3A5845. Revision B, May 2018

Table des matières

Autres manuels Graco Pistolet à peinture

Graco

Graco 232164 Manuel d'utilisation

Graco

Graco Optimiser 2K Manuel d'utilisation

Graco

Graco Ultra Max II 695 Manuel

Graco

Graco MAGNUM PROJECT PAINTER PLUS Manuel utilisateur

Graco

Graco Ultra Max II 695 Manuel utilisateur

Graco

Graco EH 333 HYDRA-SPRAY A Series Manuel d'utilisation

Graco

Graco 25A536 Manuel utilisateur

Graco

Graco PerformAA 26B570 Manuel utilisateur

Graco

Graco True Airless ProLTS 190 Manuel utilisateur

Graco

Graco 310820H Manuel utilisateur

Graco

Graco Hopper 24B250 Manuel utilisateur

Graco

Graco Ultra Max II 695 Mode d’emploi

Graco

Graco 257096 Manuel utilisateur

Graco

Graco Magnum ProX Manuel utilisateur

Graco

Graco Xtreme Mix 185 Manuel utilisateur

Graco

Graco 287328 Manuel utilisateur

Graco

Graco Gmax 7900 Manuel utilisateur

Graco

Graco HTX 2030 Manuel utilisateur

Graco

Graco Magnum X5 Manuel d'utilisation et d'entretien

Graco

Graco T-Max Applicator 256383 Manuel utilisateur

Graco

Graco Reactor E-20 Series Manuel utilisateur

Graco

Graco 308-328 Manuel d'utilisation

Graco

Graco 16R963 Manuel utilisateur

Graco

Graco RTX 1500 Manuel d'utilisation et d'entretien

Manuels Pistolet à peinture populaires d'autres marques

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuel utilisateur

Binks

Binks SV100 Manuel utilisateur

Fimco

Fimco LG-4-3-1 Manuel utilisateur

AG SPRAY

AG SPRAY FS-ATV-25BL Manuel utilisateur

Nordson

Nordson MicroMax 2 Manuel utilisateur

Bonide

Bonide 051 Manuel d'utilisation

zogics

zogics Z-DAS Manuel utilisateur

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuel utilisateur

Matrix

Matrix SG 650 Manuel utilisateur

Anest Iwata

Anest Iwata SGA-3 Guide de démarrage rapide

paasche

paasche VV Fiche technique

Carlisle

Carlisle DeVilbiss JGA-510 Manuel utilisateur

Gardena

Gardena 11120 Manuel utilisateur

Conrad

Conrad Hobby Airbrush K3 Manuel utilisateur

wiwa

wiwa 14025 R/F Manuel utilisateur

DeVilbiss

DeVilbiss LUNA2i Manuel utilisateur

WAGNER

WAGNER W 125 Manuel utilisateur

My Clean Buddy

My Clean Buddy PW018 Manuel utilisateur