Graco 24L884 Manuel
Kit Instructions
Burner Plate Assembly
Kit Number 24L884
For replacement of complete burner plate assembly on the ThermoLazer ProMelt™
Pavement Marking System (Model 24H624)
Related Manuals:
Important Safety Instructions
Read all warnings and instructions in ThermoLazer Operation manual. Be familiar
with the controls and the proper usage of the equipment. Save these instructions.
Operation 3A1319
Parts 3A1321
Repair 3A1320
Repair Kit 332742
334566C
EN
ti24785a
Warnings
2334566C
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When
these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific
hazard symbols and warnings not covered in this section may appear throughout the body of this manual where
applicable.
WARNING
WARNINGWARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent
fire and explosion:
• Use equipment only in well ventilated area.
• Do not fill fuel tank while engine is running or hot; shut off engine and let it cool. Fuel is flammable and
can ignite or explode if spilled on hot surface.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are
present.
• Ground all equipment in the work area. See Grounding instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless they are
anti-static or conductive.
•Stop operation immediately if static sparking occurs or you feel a shock.Do not use equipment until
you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
BURN HAZARD
Equipment surfaces and fluid that is heated can become very hot during operation. To avoid severe
burns:
• Do not touch hot fluid or equipment.
CARBON MONOXIDE HAZRD
Exhaust contains poisonous carbon monoxide, which is colorless and odorless. Breathing carbon mon-
oxide can cause death.
• Do not operate in an enclosed area.
Removal
334566C 3
Removal
Note: Engage rear wheel brake. Safely elevate front
wheel and support frame to aid in accessing
components on underside of unit.
1. Close manual gas shut off valve on LP-tank, discon-
nect gas supply hose and remove LP-tank.
2. Disconnect gas line (76) from tee fitting (165).
3. Disconnect gas pilot line (71) from flared adapter
(421). Only rotate the nut on gas pilot line (71), while
keeping flared adapter (421) stationary.
4. Disconnect gas line (186) from elbow fitting (161).
Disconnect gas line (48) from elbow fitting (161).
5. To uninstall gas line (48), disconnect other end of
gas line (48) from elbow fitting (32).
ti24786a
ti24787a
76 165
71
ti25692b
421
161
48
186
ti25693a
ti25155a
48
32
Removal
4334566C
6. Unplug electrode wire (217) from pulse fire igniter
(126).
7. Remove gas valve enclosure door (320) from gas
valve enclosure (28).
8. Loosen two screws on gas valve (13) to disconnect
red (top) and white (bottom) thermopile wires (7).
9. Remove screw (148) to disconnect grounding wire
(244).
10. Remove plastic bushings (357and 156) from gas
valve enclosure (28) and from wiring.
ti24790a
126
217
ti24791a
320
28
ti24792a
13
7
28
148 244
ti24793a
ti24794a
28
156
357
Removal
334566C 5
11. Pull wires (7 and 244) out of gas valve enclosure
(28).
12. Pull all wires (7, 217 and 244) through hole in arm
(23).
13. Unscrew nuts (97), remove bolts (140) and washers
(123 and 119), then lower arm (23).
14. Remove four burner plate screws (105) to
disconnect burner plate (18) from frame (55).
15. Lower burner plate (18), slide forward on top of arm
(23), and lower back end of burner plate (18) to slide
assembly out.
NOTICE
To prevent damage to wiring, ensure wires are moved
away from burner plate.
28
7
244
ti24795a
ti25156a
7
23
217
244
ti24968a
140
97
23
119
123
ti24969a
18
105
55
ti24970a
23
18
55
23
18
Installation
6334566C
Installation
1. Angle front end of new burner plate assembly (18)
over arm (23) and raise assembly up to frame (55).
2. Mount burner plate assembly (18) with four screws
(105) to frame (55).
3. Mount arm (23) with 2 bolts (140), washers (123
and 119) and nuts (97).
4. Connect gas line (76) to tee fitting (165)
ti24972a
23
18
55
ti24973a
18
105
55
ti24976a
140
97
23
ti24974a
76
165
Installation
334566C 7
5. Connect gas pilot line (71) to flared adapter (421).
Only rotate the nut on gas pilot line (71), while keep-
ing flared adapter (421) stationary.
6. Connect gas line (186) to elbow fitting (161).
Connect gas line (48) to elbow fitting (161).
7. To install gas line (48), connect gas line (48) to
elbow fitting (32).
8. Pull wires (7, 217 and 244) through hole in arm (23).
9. Draw green grounding wire (244) through gas valve
enclosure (28) and reconnect ground wire with
screw (148).
71
ti25690b
421
161
48
186
ti25691a
ti25157a
48
32
ti24978a
7
23
217
244
148
28
244
ti24979a
Installation
8334566C
10. Reconnect igniter electrode wire (217) to pulse fire
igniter (126).
11. Draw red and white thermopile wires (7) into gas
valve enclosure (28).
12. Install bushings (357 and 156) onto wires and press
into gas valve enclosure (28).
13. Reconnect red (top) and white (bottom) thermopile
wires (7) to gas valve (13).
14. Screw gas valve enclosure door (320) onto the gas
valve enclosure (28)
ti25017a
126
217
28
7
244
ti24980a
ti25014a
28
156
357
ti24792a
13
7
28
ti24791a
320
28
Installation
334566C 9
15. Safely lower unit while keeping wheel brake
engage.
16. Replace LP-tank, reconnect hose and turn LP-gas
tank valve ON
17. Check for gas leaks at final assembly (see
Operation manual).
ti25158a
Parts Drawing
10 334566C
Parts Drawing
ti25018b
1
7
18
105
120
121
130
417
418
421
420
419
208
217
225
230
231
319
405
230
225
231
11
117
165
166
117
166
Table des matières
Autres manuels Graco Pistolet à peinture
Graco
Graco Reactor 3 E-XP1 Standard Mode d’emploi
Graco
Graco 309707N Manuel utilisateur
Graco
Graco Magnum Pro Plus Mode d’emploi
Graco
Graco GM 3500 Manuel utilisateur
Graco
Graco FLEX A Series Manuel d'utilisation
Graco
Graco FUSION 248597 Manuel d'utilisation
Graco
Graco XM Series Manuel d'utilisation et d'entretien
Graco
Graco LineLazer II 3900 Manuel utilisateur
Graco
Graco FinishPro II 295 Manuel d'utilisation et d'entretien
Graco
Graco 17C301 Mode d’emploi
Graco
Graco 25D496 Manuel utilisateur
Graco
Graco 231-406, Series A Manuel d'utilisation
Graco
Graco MAGNUM PRO fineX H5 Mode d’emploi
Graco
Graco LineLazer II 3900 Manuel utilisateur
Graco
Graco M2K Manuel de la liste des pièces
Graco
Graco Dura-Flo 1100 Manuel utilisateur
Graco
Graco ProMix PD2K Manuel d'utilisation et d'entretien
Graco
Graco Pro 230ES Manuel d'utilisation et d'entretien
Graco
Graco Series E Mode d’emploi
Graco
Graco Fusion AP Manuel utilisateur
