Godex STE5 Manuel utilisateur

P/N. 920-013911-00

Rev. D, 03.2013

STE5 Operation Manual

CAUTION

Danger of explosion if battery is incorrectly replaced

Replace only with the equivalent type recommended by the manufacture.

Dispose of used batteries according to the manufacturer’s instructions.

STE5 Operation Manual

Safety Instructions

Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben.

1. Die Geräte nicht der Feuchtigkeit aussetzen.

2. Bevor Sie die Geräte ans Stromnetz anschließen, vergewissern Sie Sich, dass die

Spannung des Geräts mit der Netzspannung übereinstimmt.

3. Nehmen Sie das Gerät bei Überspannungen (Gewitter) vom Netz. Das Gerät könnte

sonst Schaden nehmen.

4. Sollte versehentlich Flüssigkeit in das Gerät gelangen, so ziehen sofort den

Netzstecker. Anderenfalls besteht die Gefahr eines lebensgefährlichen elektrischen

Schlags.

5. Wartungs- und Reparaturarbeiten dürfen aus Sicherheitsgründen nur von

autorisierten Personen durchgeführt werden.

6. Bei Wartungs- und Reparaturarbeiten müssen die Sicherheitsvorschriften der

zuständigen Berufsverbände und Behörden unbedingt eingehalten werden.

7. Bei Verletzungen unbedingt den Arzt aufsuchen und die gegebenenfalls die

zuständigen Stellen benachrichtigen. Unterlassung kann zum Verlust der

Versicherungsleistungen führen.

STE5 Operation Manual

Safety Instructions

Please read the following instructions seriously.

1. Keep the equipment away from humidity.

2. Before you connect the equipment to the power outlet, please check the voltage of the

power source.

3. Disconnect the equipment from the voltage of the power source to prevent possible

transient over voltage damage.

4. Don’t pour any liquid to the equipment to avoid electrical shock.

5. ONLY qualified service personnel for safety reason should open equipment.

6. Don’t repair or adjust energized equipment alone under any circumstances. Someone

capable of providing first aid must always be present for your safety

7. Always obtain first aid or medical attention immediately after an injury. Never neglect

an injury, no matter how slight it seems.

STE5 Operation Manual

1. BARCODE PRINTER AND RFID TAG ENCODER..................... 5

1-1. Printer Accessories......................................................................................................... 5

1-2. General Specifications....................................................................................................5

1-3. Communication Interface................................................................................................7

1-4. Printer Parts....................................................................................................................8

2. PRINTER INSTALLATION........................................................ 10

2-1. Ribbon Installation ........................................................................................................10

2-2. Label Installation...........................................................................................................12

2-3. Label Roll Core Installation Instruction .........................................................................14

2-4. Card / Hang tags Installation ........................................................................................15

2-5. PC Connection..............................................................................................................15

3. PRINTER SETTING .................................................................. 16

3-1. FEED Key .....................................................................................................................16

3-2. LED Status....................................................................................................................16

3-3. Auto Sensing.................................................................................................................16

3-4. Self-Test page...............................................................................................................17

3-5. Error Messages.............................................................................................................18

4. RFID TAG ENCODING ............................................................. 19

4-1. Install and Register Smart Media Manager ..................................................................19

4-2. RFID Tag Encoding ......................................................................................................22

4-3. RFID Utilities.................................................................................................................25

4-4. RFID Messages............................................................................................................27

5. ACCESSORY............................................................................ 28

5-1. Stripper Module Installation ..........................................................................................28

6. Maintenance and Adjustment ..........................................................................................31

6-1. Thermal Print Head Cleaning .......................................................................................31

6-2. Thermal Print Head Balance Adjustment......................................................................31

6-3. Print Line Adjustment....................................................................................................32

6-4. Adjust the cutter............................................................................................................32

6-5. Troubleshooting ............................................................................................................ 33

STE5 Operation Manual

1. Barcode Printer and RFID Tag Encoder

The main purpose of STE5 is encoding a series of label attributes into a RFID tag. It can also

print readable content on the Smart Label that contains the RFIF tag. However, it cannot perform

normal printing alone. Please note that the printing function is only available when doing RFID

encoding. The Smart Media Manger software is provided to control all of STE5 printing and

encoding functions.

1-1. Printer Accessories

After unpacking, please check the accessories that come with the package, and store

appropriately.

STE5

Power cord

Switching Power

USB Cable

Label Roll Core

Label Stop Plate

Quick Start Guide

Product CD

1-2. General Specifications

Model STE5

Print Method Thermal Transfer / Direct Thermal

Resolution 203 dpi (8 dot/mm)

Print Speed 4 IPS (100 mm/s)

Print Width 4.25” (108 mm)

Print Length Min. 0.39” (10 mm); Max. 68” (1727 mm)

Memory 4MB Flash (2MB for user storage) ; 8MB SDRAM

Sensor Type Adjustable reflective sensor. Fixed transmissive sensor, central aligned

Ribbon

Types: Wax, wax/resin, resin

Length: 981’ (300 m)

Width: 1.18” Min. - 4.33” (30 mm - 110 mm) Max.

Ribbon roll diameter: 2.67“ (68 mm)

Core diameter: 1” (25.4 mm)

RFID HF RFID tag can support the transponder ICs which the radio frequency is on

13.56MHz and follows the ISO/IEC 15693 standard

Printer Language EZPL

Software Label design software: SMM (Smart Media Manager)

Resident Fonts

Bitmap fonts: 6, 8, 10, 12, 14, 18, 24, 30, 16X26 and OCR A & B

Bitmap fonts 90°, 180°, 270° rotatable, single characters 90°, 180°, 270°

rotatable

Bitmap fonts 8 times expandable in horizontal and vertical directions

Scalable fonts 90°, 180°, 270° rotatable

STE5 Operation Manual

Barcodes

1-D Bar codes:

Code 39, Code 93, Code 128 (subset A, B, C), UCC/EAN-128 K-Mart,

UCC/EAN-128, UPC A / E (add on 2 & 5), I 2 of 5, I 2 of 5 with Shipping Bearer

Bars, EAN 8 / 13 (add on 2 & 5), Codabar, Post NET, EAN 128, DUN 14, HIBC,

MSI (1 Mod 10), Random Weight, Telepen, FIM, China Postal Code, RPS 128

and GS1 DataBar

2-D Bar codes:

PDF417, Datamatrix code, MaxiCode, QR code and Micro QR code

Code Pages

CODEPAGE 437, 850, 851, 852, 855, 857, 860, 861, 862, 863, 865, 866, 869,

737

WINDOWS 1250, 1251, 1252, 1253, 1254, 1255

Unicode (UTF8, UTF16)

Graphics Resident graphic file types are BMP and PCX, other graphic formats are

downloadable from the software

Interfaces Serial port: RS-232 (DB-9)

USB port (default on)

Parallel port: Centronics 36-pin

Control Panel Two bi-color status-LEDs: Ready, Status

Control key: FEED

Power Auto Switching 100-240VAC, 50-60Hz

Environment Operation temperature: 41°F to 104°F (5°C to 40°C)

Storage temperature: -4°F to 122°F (-20°C to 50°C)

Humidity Operation: 30-85%, non-condensing.

Storage: 10-90%, non-condensing.

Agency

Approvals FCC part 15C class B

Dimension Length: 11.2” (285 mm)

Height: 6.8” (171 mm)

Width: 8.9” (226 mm)

Weight 6 lbs (2.72Kg) ,excluding consumables

Options Label Stripper

External label roll holder for 10” (250 mm) O.D. label rolls

External label rewinder

Specifications are subject to change without notice. All company and/or product names are

trademarks and/or registered trademarks of their respective owners.

STE5 Operation Manual

1-3. Communication Interface

Parallel Interface

Handshake : DSTB connects to the printer, BUSY connects to the host

Interface cable : Parallel cable compatible to IBM PC

Pin out : See below

PIN NO. FUNCTION TRANSMITTER

2-9

19-30

34-35

/Strobe

Data 0-7

/Acknowledge

Busy

/Paper empty

/Select

/Auto-Linefeed

N/C

Signal Gnd

Chasis Gnd

+5V,max 500mA

Signal Gnd

/Initialize

/Error

Signal Ground

N/C

/Select-in

host / printer

host

printer

host / printer

host

host / printer

printer

host / printer

Serial Interface

Serial Default

Setting : 9600 baud rate no parity 8 data bits 1 stop bit XON/XOFF protocol and

RTS/CTS

RS232 HOUSING (9-pin to 9-pin)

DB9 SOCKET DB9 PLUG

--- 1 1 +5V,max 500mA

RXD 2 2 TXD

TXD 3 3 RXD

DTR 4 4 N/C

GND 5 5 GND

DSR 6 6 RTS

RTS 7 7 CTS

CTS 8 8 RTS

RI 9 9 N/C

PC PRINTER

Note The total current output from parallel port and serial port altogether can not exceed

500mA.

USB Interface

Connector Type : Type B

PIN NO. 1 2 3 4

FUNCTION VBUS D- D+ GND

STE5 Operation Manual

1-4. Printer Parts

1. Cover Open Button

2. Top Cover

3. Label Roll Core

4. Ribbon Rewind Wheel

5. Print Mechanism

6. Ribbon Rewind Shaft + Empty Ribbon Roll

7. Locking Tenon (left/right)

8. Front Cover Piece

1. LED Light (Ready)

2. LED Light (Status)

3. FEED Key

4. CF Card Slot Cove

5. Print Head Pressure Adjustment Screw (left/right)

STE5 Operation Manual

1. Ribbon Supply Shaft

2. Label Guide

3. Platen Roller

4. Print Line Adjustment Gear

5. Label Senso

1. Fan-Fold Label Insert

2. Power Switch

3. Ethernet Socket (Option)

4. USB Port

5. Parallel Port

6. Serial Port (RS-232)

7. Power Socket

* The communication ports may vary depending on product types.

Table des matières

Autres manuels Godex Étiqueteuse

Godex

Godex LZX400i Manuel utilisateur

Godex

Godex ZX1000i+ Series Manuel utilisateur

Godex

Godex ZX400+ Series Manuel utilisateur

Godex

Godex HD830i Manuel utilisateur

Godex

Godex DT4C Manuel utilisateur

Godex

Godex RT700 SERIES Manuel utilisateur

Godex

Godex DT2L Manuel utilisateur

Godex

Godex EZ-DT Manuel utilisateur

Godex

Godex C690LJ Manuel utilisateur

Godex

Godex ZX1000i Series Manuel utilisateur

Godex

Godex MX3 series: MX30 Manuel utilisateur

Godex

Godex GE300 Manuel utilisateur

Godex

Godex DT200 Series Manuel utilisateur

Godex

Godex GE300 Manuel utilisateur

Godex

Godex G E300 Manuel utilisateur

Godex

Godex DT200+ Series Manuel utilisateur

Godex

Godex BP700 Series Manuel utilisateur

Godex

Godex Stand Alone Printer Manuel utilisateur

Godex

Godex AG3000T Manuel utilisateur

Godex

Godex EZ6000 Plus Series Manuel utilisateur

Godex

Godex ZX1000i Series Manuel utilisateur

Godex

Godex EZ6000i Series Manuel utilisateur

Godex

Godex DT Series Manuel utilisateur

Godex

Godex BP1000i Series Manuel utilisateur

Manuels Étiqueteuse populaires d'autres marques

Brother

Brother P-Touch 2420PC Manuel utilisateur

newell

newell Dymo LabelManager 210D Manuel utilisateur

Brother

Brother TD-4000 Manuel utilisateur

U-Line

U-Line BROTHER H-8754 Manuel utilisateur

Tharo Systems

Tharo Systems H-435+ Manuel utilisateur

Brother

Brother E300 Manuel utilisateur

ID Technology

ID Technology 252 Manuel utilisateur

Labelmate

Labelmate MC-11 Manuel utilisateur

CAB

CAB XD4M/300 Manuel utilisateur

Avery Dennison

Avery Dennison Pathfinder 6057 Manuel de service

Brother

Brother P-touch PT-9700PC Manuel utilisateur

TSC

TSC PEX1000 Series Manuel utilisateur

Adkins

Adkins Label Master Manuel utilisateur

Epson

Epson LabelWorks LW-400 Manuel utilisateur

Primera

Primera 510212 Manuel utilisateur

Brady

Brady BradyPrinter S3100 Manuel utilisateur

DuraLabel

DuraLabel LabPRO Manuel utilisateur

Novexx Solutions

Novexx Solutions XLP 604 Manuel utilisateur