GMI PS500 Guide d'installation

Detection,Protection, Innovation

PS500 USER TRAINING

Iss.A

Detection,Protection, Innovation

•Single Button User Operation

•Integral Impact Resistant Housing

•Graphic Display with Screen Light

•4 Gases Detected Simultaneously

•High Intensity Audible / Visual Alarms

•Datalogging

•Infrared interface for data download

•Rechargeable battery

Detection,Protection, Innovation

•Certification

Hazardous areas –flammable atmospheres:

−ATEX -required for all member countries of the EU

−UL - allows use in America

Performance testing:

−MED (Ships’ Wheelmark) -EU Marine Equipment Directive

Detection,Protection, Innovation

•Ranges of Operation

–4 gases are monitored:

•0-100% LEL propane

•0-25% Oxygen (O2)

•0-1000 ppm Carbon Monoxide (CO)

•0-5% Carbon Dioxide (CO2)

•NB: this slideshow shows pics of 5 gas version

–Gases displayed simultaneously

Detection,Protection, Innovation

•Operating Procedure

–Check the Following Before Use:

•instrument is clean and in good condition

•battery is fully charged and fitted correctly

•Sensor gas inlets are clean and in good condition

•all gas ranges are operational and the instrument is zeroed

•instrument is within the calibration period

–Switch on in Fresh Air / No Faults Displayed

Detection,Protection, Innovation

•Switching the Instrument On

−Press and Hold right button for 1 s.

−Instrument begins warm-up routine. During 30 second

warm-up a countdown timer appears on the screen

−The instrument display identifies the model, serial number,

software version, datalogging option and battery status

during warm-up.

Detection,Protection, Innovation

•Warm-up Information

−Time and Date

•The time and date from the instrument’s built-in clock is displayed

−Calibration Required

•If the display below appears (audible / visual alarms are also

activated), the instrument has detected a fault in the calibration

memory. It must be switched off.

Detection,Protection, Innovation

•Warm-up Information

–Calibration Due Date

•The calibration due date is shown on the display

•If the calibration due date has expired, the audible and visual alarm

activates

•Press right Button once to acknowledge overdue calibration due date,

cancel alarms and continue with warm-up

Detection,Protection, Innovation

•Warm-up Information

–Sensor Confirmation Check

•A diamond symbol appears above each sensor to confirm

that the sensor

–has been recognised

–is working correctly

–is being zeroed

•When sensors are zeroed correctly a tick appears above each

sensor

Detection,Protection, Innovation

•Warm-up Information

–Sensor Check Failure

•If sensor(s) fail the zero check at the end of warm-up, the audible and visual

alarms activate. The instrument display will show a spanner symbol.

•To acknowledge the alarm, press the right button. This clears the audible / visual

alarm. The instrument display will show a flashing spanner symbol alternating with

the faulty sensor zero reading.

alternating

with

Autres manuels pour PS500

Table des matières

Autres manuels GMI Instrument de mesure

GMI

GMI PS200 series Mode d'emploi

GMI

GMI PS1 Guide de l'utilisateur

GMI

GMI Gasurveyor 500 Series Guide d'installation

GMI

GMI V!SA Mode d’emploi

GMI

GMI Gasurveyor 6 - 500 Mode d’emploi

GMI

GMI GT series Mode d’emploi

GMI

GMI PS200 series Guide de l'utilisateur

GMI

GMI First Responder Mode d’emploi

GMI

GMI PS200 series Manuel utilisateur

GMI

GMI PS200 series Manuel utilisateur

GMI

GMI GDUnet Mode d’emploi

GMI

GMI PS241 Mode d’emploi

GMI

GMI PS200 series Mode d’emploi

GMI

GMI PS1 Mode d’emploi

GMI

GMI GT series Manuel utilisateur

GMI

GMI GT series Mode d’emploi

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur