Gira 1264 00 Manuel utilisateur
Mounting Instructions
Call push button 1-gang for
flush-mounted outdoor station
1262 00, 1293 00
Call push button 3-gang for
flush-mounted outdoor station
1263 00, 1294 00
Information module for
flush-mounted outdoor station
1264 00, 1295 00
2
Device description
The 1 and 3-gang call buttons for the flush-
mounted outdoor station and the informa-
tion module are part of the Gira door com-
munication system and are used to expand
the flush-mounted outdoor station.
The basic structure is presented in the
example of the call push button 3-gang.
1 Audio connection cable
2 Call push button insert
3 TX_44 frame bottom section
(not in scope of supply)
4 Call push button or information module
top unit
5 TX_44 frame top section
(not in scope of supply)
6 Call push button cover
1 2 3 4 5 6
3
Mounting
The 1 and 3-gang call buttons and the infor-
mation module are operated together with
the outdoor station:
1. Insert the audio connection cable into a
system connector of the bus coupler or
speech insert of the flush-mounted out-
door station.
Attention
Installation and mounting of electrical
devices may only be carried out by a quali-
fied electrician.
Do not use the sealing rings included with
the TX_44 frame when installing flush-
mounted inserts.
i
Deactivating call push button
illumination
To deactivate the call push button illumina-
tion or illumination of the information mod-
ule continuously, remove the jumpers
between BUS and ZV at the bus coupler of
the outdoor station.
4
2. Guide the audio connection cable into
the flush-mounted panel box.
3. Insert the audio connection cable into a
system connector of the call push button
insert.
4. Install the call push button insert.
5. Set the bottom section of the TX_44
cover frame in place and attach the cen-
tral inserts to the flush-mounted inserts.
6. Clip on the frame top section and press
in the Torx screws.
Start-up
Once you have installed all of the devices
(outdoor and home stations, control unit
etc.), you can start up the door communica-
tion system.
Start-up is described in the system manual
included with the control unit.
5
Operation
Initiating a call (ringing)
Press the call push button to trigger a call
tone at the assigned home station.
The button press is confirmed by an addi-
tional acknowledgement tone.
Switching light on/off
(in conjunction with a switching
actuator)
Press the call push button to switch on light
or another device via an assigned switching
actuator. The button press is confirmed by
an additional acknowledgement tone.
6
Changing the label plates
To change the label plates, the call push but-
ton cover is simply lifted up:
1. Carefully lift up the call push button
cover, e.g. with a screwdriver.
2. Change the label plate.
3. Replace the call push button cover and
press on it firmly.
Suitable label plates can be obtained with
the optional Gira labelling software and the
appropriate Gira labelling sheets.
7
Acceptance of guarantee
The warranty is provided in accordance with
statutory requirements via the specialist
trade.
Please submit or send faulty devices post-
age paid together with an error description
to your responsible salesperson (specialist
trade/installation company/electrical spe-
cialist trade).
They will forward the devices to the Gira
Service Center.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Postfach 1220
42461 Radevormwald
Deutschland
Tel +49 (0) 21 95 / 602 - 0
Fax +49 (0) 21 95 / 602 - 191
www.gira.de
info@gira.de
10 41 03 71 19/11
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Gira Système d'interphone
Gira
Gira 2600 Series Manuel utilisateur
Gira
Gira 1288 00 Manuel utilisateur
Gira
Gira 2551 20 Manuel utilisateur
Gira
Gira Surface-mounted video home station 7 Mode d'emploi
Gira
Gira 1250 Series Manuel de service
Gira
Gira Surface-mounted video home station 7 Manuel utilisateur
Gira
Gira 1281 Series Manuel de service
Gira
Gira 1279 series Manuel utilisateur
Gira
Gira 1269 65 Manuel utilisateur
Gira
Gira 5919 Series Manuel utilisateur
