Gira 5069 00 Manuel utilisateur
Condensation sensor
Condensation sensor
Order no.: 5069 00
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. During installation and cable routing, comply with the regulations and
standards which apply for SELV circuits.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
Figure1:
(1) Connecting cable
(2) Fixing strap
(3) Recession for fitting on ductwork with cable ties
(4) Recession for a thermally conducting pad
(5) Sensor surface
3 Function
Intended use
– Detection of water condensation on coolant lines in residential or functional buildings
– Connection to suitable binary inputs
– Fitting on the coolant line
Condensation sensor function
The device monitors the electrical conductivity between the conductive coatings on the sensor
surface. If it is dampened with water, the device detects the change and signals it.
1 / 3
82595932 19.07.2021
Condensation sensor
The sensor surface can be damaged if it comes into contact with aggressive media (e.g.
detergent solutions, scrubbing brines or acidic condensation from condensing boilers).
Check the sensor area (3) every alarm. In case of significant damage from corrosion re-
place the device.
4 Information for electrically skilled persons
4.1 Fitting and electrical connection
Selecting installation location
The installation location should be the position that is most likely to have condensation. That
can be the coldest spot within a pipeline circuit.
For proper function, the sensor surface (5) must be ventilated so that condensation can form on
it.
When fitted in the vicinity of mixer valves, place the device on the colder inflow.
Fitting the condensation sensor
Figure2: Fitting to a pipe with cable ties
(6) Pipe
(7) Cable tie
(8) Thermally conducting pad
￭ Clean the outer surface of the pipe. Remove any existing remaining paint.
￭ Remove the protective film from the enclosed thermally conducting pad.
￭ Put the self-sticking thermally conducting pad (8) in the recession for the thermally con-
ducting pad (4) and slightly press on.
The thermally conducting pad adheres to the recession on the bottom side of the device.
￭ Place the bottom side of the device directly on the pipe that is to be monitored.
￭ Fit the device to the pipe with the accompanying cable ties (7).
￭ Lock the connection cable into position.
Connecting the condensation sensor
The device is connected to an evaluation unit and supplied by it.
2 / 3
82595932 19.07.2021
Condensation sensor
Figure3
￭ Connect the device to an evaluation unit (9) that supplies and monitors the device.
￭ Observe the polarity:
White = +
Brown = – / COM
5 Technical data
Rated voltage DC 3.3 ... 5 V SELV
Current consumption typ. 0.5 mA
Short-circuit current max. 100 mA
Protectionclass III
Ambient temperature 0 ... +50 °C
Storage/transport temperature -40 ... +100 °C
Connecting cable 2 m
Degree of protection IP 67
6 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
Please submit or send faulty devices postage paid together with an error description to your re-
sponsible salesperson (specialist trade/installation company/electrical specialist trade). They will
forward the devices to the Gira Service Center.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel +49(0)21 95 - 602-0
Fax +49(0)21 95 - 602-191
www.gira.de
3 / 3
82595932 19.07.2021
Table des matières
Autres manuels Gira Accessoires
Gira
Gira EDA 3902 F Manuel utilisateur
Gira
Gira 5466 02 Manuel utilisateur
Gira
Gira 0384 00 Manuel utilisateur
Gira
Gira 1117 00 Manuel utilisateur
Gira
Gira 5461 02 Manuel utilisateur
Gira
Gira KNX 5011 00 Manuel utilisateur
Gira
Gira CO2-Sensor Manuel utilisateur
Gira
Gira 234902 Manuel utilisateur
Gira
Gira 5142 00 Manuel de l'opérateur
Gira
Gira Observer 70 Manuel utilisateur
Gira
Gira 5466 02 Manuel utilisateur
Gira
Gira Observer 110 Manuel utilisateur
Gira
Gira 5111 00 Manuel utilisateur
Gira
Gira Touch sensor 2 Manuel utilisateur
Gira
Gira 5471 00 Manuel utilisateur
Gira
Gira 1025 00 Manuel utilisateur
Gira
Gira 5112 00 Manuel de l'opérateur
Gira
Gira System 55 Pushbutton sensor 4 Standard Manuel utilisateur
Gira
Gira 5472 02 Manuel utilisateur
Gira
Gira 5472 02 Manuel utilisateur
