Gibson 5206 Manuel utilisateur
INSTRUCTION MANUAL
CAT BACK DUAL SPORT EXHAUST
01-04 SILVERADO /SIERRA TRUCK 2500HD 3500HD
8.1L-V8 2/4WD
CREW CAB, LONG BED
PART # 5206
ITEM PART # QUANTITY DESCRIPTION
A 700343 1 3” PSGR. HEADPIPE W/WELDED HANGER
G A G I E F F
G B G C H D J
B 700329 1 3” DRIVER SIDE HEADPIPE
C 766300 1 SUPERFLOW MUFFLER
D 700330 1 2-1/2” DRIVERSIDE TAILPIPE W/HANGER
E 700331 1 2-1/2” PASSENGER TAILPIPE
F 500374 2 3 ½” STAINLESS TIPS
G OHD300 4 3” CLAMPS
H 4164 1 2-1/2” HANGER FOR MUFFLER D/S
I 5757 1 2-1/2” CLAMP
J BO-906 1 BOLT KIT FOR TAILPIPE
THANK YOU FOR CHOOSING OUR GIBSON PERFORMANCE EXHAUST FOR YOUR VEHICLE.
IF YOU NEED FURTHER ASSISTANCE, PLEASE DO NOT HESITATE TO CALL OUR
TECHNICAL DEPARTMENT AT (800) 528-3044, MONDAY THROUGH FRIDAY,
8:00 AM TO 5:00 PM. 1005
EXHAUST INSTALLATION #5206
WHEN INSTALLING THIS EXHAUST SYSTEM MAKE SURE TO USE PROPER SAFETY
PRECAUTIONS. USE JACK STANDS WHEN UNDER THE TRUCK, SET PARKING BRAKE,
BLOCK TIRES AND USE SAFETY GLASSES AND GLOVES.
DO NOT WORK WITH HOT PIPES!!!
SUGGESTED TOOLS
15MM SOCKET & WRENCH, 9/16”,7/16”,1/2” SOCKET & WRENCH, JACK STANDS, WD-40, HACKSAW
LAY OUT THE EXHAUST AND COMPARE PART NUMBERS WITH THE DRAWING
INSTALL YOUR
STAINLESS STEEL
TIPS. TO CLEAN TIPS
USE A SCOTCH BRITE
PAD AND ANY
STAINLESS OR
ALUMINUM CLEANER.
AFTER YOU HAVE
CHECKED FOR
CLEARANCES GO
BACK AND TIGHTEN
ALL NUTS, BOLTS
AND CLAMPS.
SLIDE PASSENGER SIDE
TAILPIPE #E INTO OUTLET
OF MUFFLER 1-1/2” TO 2”.
USE CLAMP #I TO SECURE
TAILPIPE TO MUFFLER.
DO NOT TIGHTEN.
TO REMOVE STOCK
EXHAUST, CUT 13” FROM
THE FRONT OF THE
MUFFLER, MEASURE
TOWARDS THE FRONT OF
THE VEHICLE. LEAVE ALL
RUBBER GROMMETS ON
THE HANGER. USE WD-40
TO AID IN THE REMOVAL OF
EXHAUST AND HANGERS
SLIDE DRIVERS SIDE
TAILPIPE #D INTO
MUFFLER 1-1/2” TO 2”.
INSERT WELDED
HANGER INTO
RUBBER GROMMET
AND ATTACH TO
MUFFLER USING
CLAMP #H. THE
PASSENGER SIDE
TAILPIPE WILL BE ON
THE BOTTOM.
ATTACH BOTH
TAILPIPES TOGETHER
WITH BOLT KIT #J.
SLIDE PASSENGER SIDE
HEADPIPE #A ONTO STOCK
HEADPIPE. INSERT WELDED
HANGER INTO RUBBER
GROMMET. NEXT INSTALL
DRIVERS SIDE HEADPIPE #B
ONTO STOCK HEADPIPE,
USE CLAMP #G TO SECURE
HEADPIPES, DO NOT
TIGHTEN.
SLIDE MUFFLER #C ONTO
HEADPIPES 1-1/2” TO 2”.
OUTLETS SHOULD BE AT
THE BOTTOM, USE A
JACK STAND TO
SUPPORT MUFFLER AND
CONNECT WITH CLAMPS
#G. INSTALL CLAMP #H
INTO RUBBER GROMMET
JUST ABOVE DRIVERS
SIDE OF MUFFLER
OUTLET. YOU WILL USE
THIS CLAMP TO SECURE
TAILPIPE TO MUFFLER,
“MAKE SURE YOU HAVE A MINIMUM OF 1” CLEARANCE ON ALL PIPES
FROM BRAKE AND FUEL LINES
,
TIRES
,
SHOCKS
,
ETC…”
Autres manuels Gibson Autre
Gibson
Gibson 69207D Manuel utilisateur
Gibson
Gibson 65626 Manuel utilisateur
Gibson
Gibson 98001 Manuel utilisateur
Gibson
Gibson 98023 Manuel de service
Gibson
Gibson 616601 Manuel utilisateur
Gibson
Gibson 615598 Manuel utilisateur
Gibson
Gibson 9522 Manuel utilisateur
Gibson
Gibson 5300 Manuel utilisateur
Gibson
Gibson 69218D Manuel utilisateur
Gibson
Gibson 5669 Manuel utilisateur
