GeoSIG GMS plus Guide d'installation

FAQ GMSplus How to Use as NTP Client ¶

1. Introduction

This procedure describes how to set a GMSplus as NTP client.

It will allow the GMSplus to synchronize its time with a NTP server.

2. Required Tools

GMSplus with network connection

Domain or IP address of a NTP server.

It can be a public server (see e.g. pool.ntp.org), a dedicated server in your network (check with your network admin) or a

GMSplus with a GPS configured as NTP server (http://www.geosig.com/files/FAQ_GMSplus_How_to_Use_as_NTP_Server.pdf)

3. Enter NTP server in GMSplus config

The NTP server can either be entered through the webinterface (3.1) or from GMSplus serial console (3.2)

3.1 Enter NTP Server through Webinterface

Open your webbrowser, enter the IP address of your GMSplus and login as admin (default password 123456)

Choose tab Configuration and click Miscellaneous Parameters

Click Time synchronization

Choose Time source NTP from the dropdown

Enter the IP or domain of your primary NTP server

Enter the IP or domain of your secondary NTP server (enter the primary NTP server again if you don't have a secondary)

Click Apply and Restart and confirm the pop-up with Yes to apply the changes

3.2 Enter NTP Server from GMSplus Serial Console

Connect to the serial console of your GMSplus

Press C to enter the configuration menu and press C again to edit current configuration

Press O to enter Miscellaneous Parameters

Press K to enter Time synchronization

Press A until Time source shows NTP

Press I to enter the IP or domain of your primary NTP server

Press J to enter the IP or domain of your secondary NTP server (enter the primary NTP server again if you don't have a

secondary)

Press Esc followed by ENTER and again Esc followed by ENTER to get back to the main menu

Press Esc to exit the menu

Press C to save the configuration as "current"

In the main menu, press R followed by Enter to restart the instrument

After the restart, the configuration changes are applied

Make sure that SOH status of the time sync shows Locked (can take several minutes)

Autres manuels pour GMS plus

Autres manuels GeoSIG Instrument de mesure

GeoSIG

GeoSIG GMS-GPS Manuel utilisateur

GeoSIG

GeoSIG AC-23 Manuel utilisateur

GeoSIG

GeoSIG AC-73-DH Instructions d'installation et d'utilisation

GeoSIG

GeoSIG GMS-scai Guide d'installation

GeoSIG

GeoSIG AC-73 Manuel utilisateur

GeoSIG

GeoSIG GMS plus Manuel du propriétaire

GeoSIG

GeoSIG GMS plus Manuel utilisateur

GeoSIG

GeoSIG GSR Series Manuel du propriétaire

GeoSIG

GeoSIG AC-23 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur