GeoCross VisionDrive VD-5000 Manuel utilisateur
2
3
5
6
7
8
9
10
15
19
27
INDEX
Before Use
Caution
Components
Part Names
Product Specications
Installation Precautions
Installation Sequence
Installation Procedure
Product Use
Analysis Program Use
Warranty
Before Use
Thank you for choosing VisionDrive .
The following contents describe the scope of the warranty service covered by us and product
cautions.
Warranty Service and Responsibility
We shall not be held responsible for damage caused by errors or data loss of this product, as
well as any damages or losses derived from the device not operating normally.
The product is designed to record, store, play and analyze videos caused by impacts and car
accidents or as recorded by user’s discretion. However, it is not assured that the product will
record video in every instance.
Furthermore, under circumstances where the impact is too weak, the vibration sensor may not
be able to detect the impact, which induces that the system will be unable to automatically start
recording the [Event] file. In such a situation, the urgent save button (SHOT) on the product
should be pressed to start recording a video to the [Event] folder.
The information in this manual may change without prior notice due to technical changes or
upgrades. Check for updates periodically to ensure full knowledge of both the warranty service
and responsibility scope.
Caution
The SD card is the only usable SD card for this product.
In case of a lost SD card, please contact your local retail shop to purchase a replacement.
If a damaged or a non-authentic SD card is used, the recorded data maybe damaged or will not
record and/or replay due to difference in quality.
Caution
Do not disassemble or remodel this product as it can cause an electric shock.
Any malfunctioning after such action will result in the product being unfit for use and void all
warranty/service provisions.
Consult the retailer for product maintenance and repairs if necessary.
Only use adaptors with the appropriate specifications. The use of other adaptors will defect the
product and or cause fire.
All wiring should be carefully implemented so the cable may not be damaged.
When installing the device to your vehicle, follow all the procedures and make sure the mount is
secure. Unclean surfaces will weaken the adhesive strength and can damage the product if it
drops due to weak adhesion.
This product is not waterproof. Do not allow liquids and impurities to enter the product.
Where the product is wired to the power supply of the vehicle directly or if the cigar jack is
connected to the power supply while the engine is off, make sure to disconnect the device to
prevent battery drain on your vehicle.
Do not use chemicals or detergents to clean the device. This can result in malfunctioning of the
product.
Accumulation of impurities on the camera lens or the window surface near the camera may
result in video distortion and reduced clarity of recorded data.
These areas of the product should always be kept clean.
Excessive tinting on the window may also distort or reduce clarity of recorded data.
Note : Recording can be distorted under the condition where brightness suddenly changes like
passing through a tunnel, direct sunlight reflection during day time or where only low light is
available at night time.
If not enough light is available, using additional external lighting may help record better images.
Caution
In case of slight impact, the product may not be able to create an event file automatically (it is
however recorded as a Normal file). In such a case, please use the (SHOT) button to create an
event file manually.
If you eject the SD card while the product is on, the recorded data may be damaged.
Make sure the main power is completely off and the device is fully powered off (no indicator
lights are on) before removing the SD card from the product.
Interacting with the product while driving is risky and may cause an accident. This should only
be performed when the vehicles is stationary and parked in a safe place.
Dropping or causing an impact on the product during operation can cause defects or fire.
Do not keep the product in extreme temperatures or in humid areas.
Being under extreme heat in summer days or freezing cold in winter days may result in defection
of the product. Also, do not expose the product to direct fire or water.
Do not disassemble the product.
Disassembly without caution may result in product defect.
Keep the SD card in its case when not in use in the product.
Static electricity or other environmental elements can damage the recorded data.
SD cards are an expendable supply. After normal periods of use, partial memory sectors may
be damaged and will disable the recording of data.
The system installed on the SD card provides an automated checking function.
If use of the automatic checking function identifies problems with the SD card then we
recommend purchasing a new SD card for recording data.
If the SD card is ejected or the system is turned off while recording, copying or deleting a data,
stored data may be lost or damaged.
In a worst case scenario, the SD card may become defective.
We, the company, are not responsible for loss or destruction of stored data.
Copy and keep important data on other data storages such as hard disk, CD, portable flash
memory.
Components
!! Components are subject to change without prior notice.
Main Unit
Attachment
Bracket
(Mount)
SD card Wire holders Cigar Power
Adaptor
5
6
Part Names
MIC
VIEW BUTTON
PLAY BUTTON
SHOT BUTTON
LCD SCREEN
GPS SENSOR
CAMERA
SD CARD SLOT
BRACKET ATTACHED TO THE UNIT’S BODY
POWER PORT
TECH SUPPORT PORT
7
Product Specication
Model VISIONDRIVE VD-5000(W)
Camera
0.3M pixel (WDR) CMOS digital camera
Resolution
640x480(VGA) 30fps Max.
Recording
24Hr Loop Recording / Manual & Emergency Recording button
Lighting Environment Min. 0.1 Lux
Camera Angle
156°
Camera Rotation
Vertical 65°
Display
2.4" TFT Color LCD
GPS
Built-in GPS Module (Sirf III)
G-sensor
Built-in 3-Axis Sensor(x-y-z)
Storage
SD memory card (SDHC compatible 1G ~ 32G)
Audio Recording
built-in MIC (One-touch recording)
Voice Announcement
Built-in Speaker
Event Recording
Before impact 10 sec./ After impact 15/30/45/60 sec.
Power Supply
DC 12V ~ 24V Cigar Power
Internal Battery
EDLC for Emergency backup
Operation Temperature
-20 °C ~ 60 °C
Size
111mm * 75mm * 27mm
PC OS
Windows XP/ VISTA / Windows 7
File Protection
Password setting
Analyzer Program
Dedicated Analyzer (AVI file transformation support)
8
Installation Precautions
For safe installation and operation, carefully read all the information stated below.
DO NOT disconnect the power supply while the system is booting up.
Be aware of engine ignition switching for they may disconnect power for short periods of
time.
It is recommended to only use authorized SD cards with the VisionDrive products.
Install the product after parking your vehicle in a bright and safe area.
Install the system when ignition is off, especially after the power source has been turned off
completely.
Use the power cable provided with the product for the cigarette lighter power connection for
power in the range of DC12V to DC24V. If power wiring is involved, we recommend a
professional service for the installation.
Prior to the installation, clean the area of the installation where the camera will be positioned.
DO NOT eject the SD card while the product is in operation.
9
Installation Sequence
Connect the bracket and the main unit
Insert SD card into the unit
Connect cable and attach on windshield
Connect to power source and turn on the unit
Adjust the camera angle
Check LED lamps
Arrange wires using wire holders
1.
2.
3.
4.
5.
6.
7.
Ce manuel convient aux modèles suivants
1
Table des matières
