Genie GCL-LT Manuel utilisateur

Light-Duty Trolley Operator

for Sectional Doors

-DutyOperator

GCL-LT

Light

12/2022

Light

Duty Trolley Operator

This installation manual provides the information required to install,

program, troubleshoot and maintain a GCL-LT operator.

For use only on the following types of doors:

• Sectional Doors - Standard Lift

APPLICATIONS:

UL 325 Listed for residential and commercial applications

113228.01077

Models: OPGLDT0011

OPGLDT0011W

OPGLDT0011WB

PLACE iDCM SERIAL NUMBER DECAL HERE IF Optional

iDCM KIT IS INSTALLED

SERIAL NUMBER DECAL

The included Safe-T-Beam®system, or other monitored safety device UL 325 Listed for use on this model,

MUST be installed to close the door. DO NOT use other brands or types of monitored entrapment.

Door maximum weight / height:

• 750 lbs. / 14 ft.

SAFETY & STANDARD FEATURES

1.Safe-T-Beam®(STB)Non-ContactReversingSystem:

• Places an infrared beam across the door opening.

• Only aects the DOWN travel of the door.

• Stops an open door from closing or reverses a door while in the down travel.

• Reversing system can be overridden with constant pressure on the wired wall console only.

• The door will stop and reverse to the full open position if beam is obstructed.

• Self-diagnostic LEDs on STBs and Powerhead alert to operational issues (See Locating Safe-T-Beam® Pairs &

Troubleshooting section in this manual for more information).

2.ContactReversingSystem:

• Automatically reverses a closing door upon contact with an obstruction (Force Control)

3.ManualEmergencyReleasepullhandle&cord:

• Manually releases door from door opener. Used during a power failure or other emergency to allow manual

opening and closing of the door.

• DO NOT use emergency release cord to pull the door!

4.AutomaticLightingSystem:

• Lighting system turns ON when door is activated and automatically turns OFF 4 minutes later.

• Can be activated/deactivated manually from the wall console.

5.GenieBatteryBackup(BBU):

• Included or optional with select models. Provides power to opener in the event of a power failure. DO NOT

install BBU until opener is fully installed, programmed and tested.

6.IntegratedAladdinConnect®(iDCM):

• Available with select models, allows operation of the garage door opener with a secure mobile device

application (app) from anywhere.

7.WallConsole:

• Wired Wall Console included with select models. Operates door opener from inside garage with an open/

close button. Has a light manual control and override. Sure-lock™ security activate switch to lock out all

remote control operation.

• Wireless Wall Console included with select models. Operates door opener from inside garage with an

open/close button. Has a light manual control and override. Features a 10 second delay button

8.Intellicode®Encryption,FactoryProgrammedRemote(s):

• An encryption system that enhances the security of the door opener by continuously changing the access

code each time the remote is used.

• Factory programmed remote control(s) included with this opener.

Vehicle

Compatible

Cycle Rating:

• 8 cycles/hour maximum up to 25 cycles/day

INDEX

SAVE THESE INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS

FCC Part 15.21 Statement:

Changes or modications not expressly approved

by the party responsible for compliance could void

the user’s authority to operate the equipment.

FCC / IC Statement:

This device complies with FCC Part 15 and Industry

Canada licence-exempt RSS standard(s). Operation

is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2)

this device must accept any interference received,

including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR

d’Industrie Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée

aux deux conditions suivantes : (1) l’appareil ne

doit pas produire de brouillage, et (2) l’utilisateur

de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

General Information & Instructions:..................1

Safety & General Information:

Safety Information and Instructions...................1-4

Important Installation Instructions.........................5

Approved Safety Devices ...........................................6

Assembly & Installation Of Operator:...............7

Pre-Installation Considerations................................7

Assemble Operator ......................................................8

Install Rail Assembly to Operator ...........................8

Install Header Bracket .................................................9

Determine Highest Point of Travel .........................9

Install Operator Rail to Header Bracket ............. 10

Mount Operator to the Ceiling ............................. 11

Attach Bracket and Draw Bar Arm to Door 12-13

Wire Operator, Install & Wire Accessories:... 14

Tools Required & Typical Installation................... 14

Install and Wire Wired Wall Console..................... 15

Install And Wire Monitored Safety Device......... 16

Wired Monitored Photocells (Std. Equip.)....... 16

Wired Monitored Reective Photocells (Optional)

Wired NEMA 4X Photocells (Optional)............. 17

Wired Monitored Light Curtain (Optional)..... 18

Wired Safety Edge Instructions (Optional)..... 19

Wireless Monitored Safety Edge (Optional)... 20

Install Light Bulbs and Lens Cover ....................... 21

Installing Battery Back Up (Optional).................. 22

Apply Power to Operator......................................... 23

Optional Permanent Input Wiring........................ 23

Programming Operator and Accessories:.... 24

Down Travel Limit....................................................... 25

Up Travel limit.......................................................................26

Force Control Adjustments..................................... 27

Contact Reverse Test ................................................. 27

Contact Reverse Adjustment ................................. 27

Transmitter Programming (if applicable) .......... 28

Accessory Programming

Wireless keypad (if applicable) ........................... 29

Built in Vehicle Transmitter (if applicable)...... 29

Wireless Wall Console (if applicable) ................ 30

Integrated Aladdin Connect (if applicable)..

31-32

Connect Battery Backup to Operator.................. 32

For patent information go to

www.geniecompany.com

patents

Special Installation Information:...................... 33

Changing Force Settings ......................................... 33

Clearing Memory of Accessories ......................... 34

Toggle Enable/Disable STB-Triggered

Work Light Features...................................................... 34

Adjusting Speed Control ........................................ 35

Maintenance: ............................................................. 36

Door Inspection.......................................................... 37

Replacing Batteries.................................................... 38

Changing Light Bulbs ............................................... 38

Troubleshooting & LED Signals: .................39-40

Replacement Parts:...........................................41-42

DASMA Safety Guidelines: ............................43-44

Warranty: ..................................................................... 45

Check working condition of door before installing the operator. Door must be free from sticking and

binding. If equipped, deactivate any door locking device(s). Door repairs and adjustments, including

cables and spring assemblies MUST be made by a trained service representative using proper tools and

instructions.

CAUTION

ATTENTION

Vériez l’état de fonctionnement de la porte avant d’installer l’opérateur. La porte doit pouvoir bouger

librement et ne pas coincer. Désactivez tous les dispositifs de verrouillage de la porte (si équipés). Les

réparations et les réglages de porte, plus particulièrement pour les câbles et les ressorts DOIVENT être

eectués par un technicien qualié qui se sert d’outils appropriés et qui respecte les instructions.

GENERAL INFORMATION AND INSTRUCTIONS

DO NOT apply line voltage until instructed to do so.

WARNING

AVERTISSEMENT

NE PAS mettre sous tension tant que l’instruction n’est pas donnée de le faire.

Job Site Considerations

The following list of items should be evaluated prior to selecting an operator for a given job site.

1. Available 120 VAC 1A power source.

2. Type of door.

3. Potential operator mounting obstructions. Items to consider include, but are not limited to room above

door shaft, room below door shaft, available mounting surface integrity, power source location, and

convenient release cable positioning.

4. Size of door for appropriate operator torque and door travel speed selection.

5. Operator mounting environment. Items to consider include operator location, dampness of location,

dustiness of the location and corrosiveness of the location.

6. Accessory equipment. Examples include type of monitored safety device, radio controls, push button

stations, wireless/wired keypads.

SAFETY INFORMATION AND INSTRUCTIONS

POTENTIAL HAZARD EFFECT PREVENTION

MOVING DOOR WARNING

Could result in Serious

Injury of Death

Do Not operate unless the doorway is in sight and free of obstructions.

Keep people clear of opening while door is moving.

Do Not allow children to play with the door operator.

Do Not operate a door that jambs or one that has a broken spring.

ELECTRICAL SHOCK WARNING

Could cause Serious

Injury or Death

Turn o electrical power before removing operator cover.

When replacing the cover, make sure wires are not pinched or near moving

parts.

Operator must be electrically grounded.

HIGH SPRING TENSION WARNING

Could cause Serious

Injury or Death

Do Not try to remove, repair or adjust springs or anything to which door

spring parts are fastened, such as wood block, steel bracket, cable or any

other structure or like item.

Repairs and adjustments must be made by trained service representative

using proper tools and instructions.

WARNING

Garage Doors are large, heavy objects that move with the help of springs under high tension and electric

motors. Since moving objects, springs under tension, and electric motors can cause injury, your safety and

the safety of others depend on you reading the information in this manual. If you have any questions or

do not understand the information presented, call your nearest service representative. For the number of

your local Genie Dealer at 1-800-OK-GENIE

In this manual the words Danger, Warning, and Caution are used to stress important safety information.

The word:

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION indicates potentially hazardous situation which, if not avoided, may result in injury or

property damage.

The word NOTE,is used to indicate important steps to be followed or important considerations.

SAFETY INFORMATION AND INSTRUCTIONS

1. Read manual and warnings carefully.

2. Keep the door in good working condition. Periodically lubricate all moving parts of door.

3. If door has a sensing edge, check operations monthly. Make any necessary repairs to keep it functional.

4. AT LEAST twice a year, manually operate the door by disconnecting it from the operator with the door in the

closed position. The Door should open and close freely. If it does not, the door must be taken out of service and

a trained service representative must correct the condition causing the malfunction.

5. This operator motor is protected against overheating by limiting the number of cycles that can be run within

a specied period. Once the cycle limit has been exceeded, the controls will disable motor operation until the

motor cools down. The operator will automatically resume normal function once this occurs.

6. In case of power failure, the door can be operated manually by pulling the release cable to disconnect the

operator drive system. The door should be in the closed position before pulling the release cable whenever possible.

7. Keep instructions in a prominent location near the pushbutton.

IMPORTANT

READ PRIOR TO ANY DOOR OPERATION

DANGER POTENTIEL EFFET PRÉVENTION

PORTE EN MOUVEMENT

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la

mort

Utiliser uniquement si la porte est en vue et libre de tout obstacle. Ne

laisser personne se tenir dans l’ouverture de la porte pendant qu’elle est en

mouvement.

Ne pas permettre aux enfants de jouer avec l’opérateur de la porte.

Ne pas modier la commande de l’opérateur à contact momentané à moins

qu’un moyen d’inversion externe soit installé.

Ne pas faire fonctionner une porte qui bloque ou dont le ressort est cassé.

CHOC ÉLECTRIQUE AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la

mort

Couper le courant avant d’enlever le couvercle de l’opérateur.

Lorsque le couvercle doit être remplacé, s’assurer que les ls ne sont ni

coincés ni près des pièces mobiles.

L’opérateur doit être correctement mis à la terre.

TENSION ÉLEVÉE RESSORT AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la

mort

Ne pas essayer d’enlever, réparer ni ajuster les ressorts ou toute autre

pièce à laquelle le ressort de la porte est attaché, y compris blocs de bois,

supports en acier, câbles ou autres articles semblables.

Les réparations et les réglages doivent être eectués par technicien qualié

qui se sert d’outils appropriés et qui respecte les instructions.

Les portes motorisées sont grandes objets lourds qui fonctionnent à l’aide de ressorts soumis à une haute

tension et de moteurs électriques. Dans la mesure où les objets en mouvement, les ressorts sous tension et les

moteurs électriques peuvent entraîner des blessures, votre sécurité et celle des autres exigent que vous preniez

connaissance des informations stipulées dans ce manuel. Si vous avez des questions ou si vous ne comprenez pas

les informations ci-incluses, veuillez contacter le représentant de service le plus près. Pour obtenir le numéro du

revendeur Genie local, appelez le +1 (800)-OK-GENIE.

Dans ce manuel, les mots Danger, Avertissement, et Attention sont utilisés pour faire ressortir d’importantes

informations relatives à la sécurité. Le mot :

DANGER signale une situation dangereuse imminente qui si elle n’est pas évitée, risque d’entraîner des blessures

graves, voire mortelles.

AVERTISSEMENT signale une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner

la mort ou des blessures graves.

ATTENTION signale une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner des

blessures ou des dommages matériels.

Le terme REMARQUE est utilisé pour signaler les étapes importantes à suivre ou d’importants éléments à prendre en

considération.

AVERTISSEMENT

SAFETY INFORMATION AND INSTRUCTIONS

1. Safe-T-Beam® (STB) Non-Contact Reversing System:

• Places an infrared beam across the door opening.

• Only active during the down travel of the door.

• Stops an open door from closing.

• The door will stop and reverse to the full open position if beam is obstructed while the door is closing.

• Reversing system can be overridden with constant pressure on the wall console until the door reaches the

closed position.

• If the door is stationary in any position other than fully closed, obstructing the infrared beam will cause the

work light to turn on for 4 minutes (if this feature has not been deactivated).

• Self-diagnostic LEDs on STBs and operator alert to operational issues (See Locating Safe-T-Beam® Pairs &

Troubleshooting section in this manual for more information).

2. Contact Reversing System:

• Automatically reverses a closing door upon contact with an obstruction (Force Control)

3. Manual Emergency Release pull handle & cord:

• Manually releases door from door operator. Used during a power failure or other emergency to allow

manual opening and closing of the door.

• DO NOT use emergency release cord to pull the door!

4. Automatic Lighting System:

• Lighting system turns ON when door is activated and automatically turns OFF 4 minutes later.

• Light can be activated/deactivated manually from the wall console.

5. Genie Battery Backup (BBU):

• Included or optional with select models. Provides power to operator in the event of a power failure. DO

NOT connect BBU until operator is fully installed, programmed and tested.

6. Integrated Aladdin Connect® (iDCM):

• Available with select models, allows operation of the garage door operator with a secure mobile device

application (app) from anywhere.

7. Wall Console:

• Operates door operator from inside garage with an open/close button. Has a light manual control and

override. Sure-Lock(TM) security activate switch to lock out all remote control operation.

8. Intellicode®Encryption Remotes (Optional):

• An encryption system that enhances the security of the door operator by continuously changing the access

code each time the remote is used.

IMPORTANT INSTRUCTIONS D’INSTALLATION

AVERTISSEMENT

Pour réduire les risques de blessures graves ou de mort:

1. Lisez Cette Notice Et Conformez-Vous Aux Instructions.

2. Ne Posez Cet Ouvre-Porte Que Sur Une Porte De Garage Correctement Équilibrée. Une Porte Mal Équilibrée

Peut Causer Des Blessures Graves. Conez La Réparation Des Câbles, Des Ressorts Et De Tout Autre

Élément À Un Technicien Qualié Avant D’entreprendre L’installation.

3. Enlevez Les Cordes Et Enlevez Ou Neutralisez Tout Dispositif De Verrouillage Solidaire De La Porte De

Garage Avant L’installation.

4. Dans La Mesure Du Possible, Installez L’ouvre-Porte À Au Moins 2,14 M (7 Pi) Du Sol. Posez Le Dispositif De

Désaccouplement D’urgence À Au Moins 1,83 M (6 Pi) Du Sol En Évitant Le Contact Avec Des Véhicules

Pour Éviter Tout Déclenchement Accidentel.

5. Ne Branchez Pas L’ouvre-Porte Avant D’y Être Autorisé Par La Notice

6. Installez Le Bouton De Commande A) À Un Endroit Que L’on Peut Voir De L’embrasure De La Porte;

B) À Une Hauteur Minimale De 1,53 M (5 Pi) Du Sol — An Que Les Jeunes Enfants Ne Puissent Pas

L’atteindre ; Et C) À L’écart Des Pièces Mobiles De La Porte.

7. Apposez L’étiquette De Mise En Garde Relative Au Danger De Happement À Proximité De Bouton

De Commande Et L’étiquette Relative Au Réglage De La Commande À Un Emplacement En Évidence – Par

Exemple Sur La Paroi Intérieure De La Porte De Garage Ou Selon Les Instructions De La Notice D’installation.

Apposez L’étiquette Relative Au Désaccouplement D’urgence Sur Le Dispositif Ou À Proximité De Ce Dernier.

Une Fois L’ouvre-Porte Installé, Le Sens De La Course Doit S’inverser Lorsque La Porte Entre En Contact Avec

Un Objet D’une Hauteur De 38 Mm (1 1/2 Po) (Ou Un Madrier De 2 × 4 Po De Section, À Plat) Posé Sur Le Sol

9. Pour Les Produits Munis D’un Dispositif De Désaccouplement Manuel, Indiquez À L’utilisateur Final La

Procédure D’utilisation Du Dispositif.

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING

To reduce the risk of severe injury or death:

1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

2. Install only on a properly operating and balanced garage door. An improperly balanced door has the potential

to inict severe injury. Have a qualied service person make repairs to cables, spring assemblies, and other

hardware before installing the operator.

Remove all pull ropes and remove, or make inoperative, all locks connected to the garage

door before installing the operator.

4. Where possible, install the door operator 2.14 m (7 ft) or more above the oor. For products having an

emergency release, mount the emergency release within reach, but at least 1.83 m (6 ft) above the oor and

avoiding contact with vehicles to avoid accidental release.

5. Do not connect the door operator to source of power until instructed to do so.

6. Locate the control button: (a) within sight of the door, (b) at a minimum height of 1.53 m (5 ft) above oors,

landings, steps or any other adjacent walking surface so small children are not able to reach it, and (c) away

from all moving parts of the door.

7. Install the Entrapment Warning Label next to the control button in a prominent location. Install the Emergency

Release Marking. Attach the marking on or next to the emergency release.

8. After installing the operator, the door must reverse when it contacts a 38-mm (1-1/2-inch) high

object (or a 2 by 4 board laid at) on the oor.

9. For products having a manual release, instruct the end user on the operation of the manual release.

SAFETY INFORMATION AND INSTRUCTIONS

Standard Commercial Photocells with Extendable Brackets

38176R.S KIT,PHOTOCELLS,COMMERCIAL (STANDARD EQUP.)

Protected Commercial Photocells with Extendable Brackets

OPAKPE2.S KIT,PHOTOCELLS W/COMM BRKT

NEMA 4X Photocells

OPAKPEN4GX.S KIT,PHOTOCELLS,NEMA-4X,50 FT

Retro Reective N4X Photocells

OPGAKRPEN4X.S KIT,PHOTOCELLS,REFLECTIVE,GENIE

Monitored Light Curtains (Powered with Transformer 36238A)

OPAKMLC3.S KIT,LIGHT CURTAIN,3FT

OPAKMLC6.S KIT,LIGHT CURTAIN,6FT

DC/T3 Monitored Edge Interface Adapter (Commercial Applications Only)

OPAKMEIGX.S KIT,MONITORED EDGE X-SERIES Genie

Wireless Edge Kit (Powered with Transformer (36238A) (Commercial Applications Only)

OPAKRWET2.S KIT,XMTR/RCVR,SENSING EDGE,WIRELESS,T2

ENTRAPMENT PROTECTION:

The installation of a monitored fail-safe external reversing device is required on all momentary contact

electronically operated commercial doors. If such a reversing device is not installed, the operator will

revert to a constant contact control switch for close operation.

Reversing devices currently UL Approved for use with this model are:

APPROVED SAFETY DEVICES

OPAKRWET3.S KIT,XMTR/RCVR,w/CONVERTER,SENSING EDGE,WIRELESS,T3

There are a few specic areas which might require extra materials:

This operator includes parts and supplies needed for installation in most garages and on most garage doors.

There are many variations of garages and garage doors. A few additional parts and supplies may be needed

for installation in your garage and to your garage door. While going over these instructions, please note the

additional items you may need. For help nding a local Genie® Professional Dealer, refer to the dealer locator

at www.GenieCompany.com or call Customer Service at 1-800-35-GENIE.

• The header above the garage door where torsion springs are used Does it extend

far enough above the spring(s) to allow mounting of the header bracket? If not, or if you can’t

tell, you will probably need a piece of 2”x 6”lumber to span across wall studs.

• The area overhead where the operator will be mounted: if you have a nished

ceiling, you will need perforated angle which can span across beams or trusses.

• Is there wood along the door tracks near the oor where the Safe-T-Beam® can be

most easily mounted, or will you need fasteners or some other material for mounting to the track

itself? Will you need extension brackets or wooden blocks to extend the Safe-T-Beam far enough o

the wall to see past any door hardware?

•

Does the application require permanent wiring installed to the operator? If so, see optional permanent input

wiring installation section.

• Is there an electrical outlet within approximately 6’of the point where the operator will be? If

not, you need to contact a licensed electrician to install an outlet.

• Check condition of the door and all its associated hardware: Tracks, springs, hinges, rollers.

Is anything loose or appear to be worn? If so, have the door serviced by a trained professional.

ASSEMBLY & INSTALLATION OF OPERATOR

PRE- INSTALLATION CONSIDERATIONS

1. Flip rail over and slide drive gear over motor shaft.

2. Install rail brackets onto rail and secure to

operator with 1/4”- 14 - 5/8”screws. Do not over-tighten.

FIG. 1. Do not install lens cover at this time.

FIG.1

A = Operator assembly

B = Battery backup (BBU)

C = Wall console control

D = Lens cover

E = Curved door arm

F = Photocell kit

G = Rail assembly

H = Parts Bag

I = Parts Bag

INSTALL RAIL ASSEMBLY TO OPERATOR

UNPACK, INVENTORY, AND INSPECT ALL PARTS & ACCESSORIES THAT THIS OPERATOR SHOULD HAVE

ASSEMBLE OPERATOR

CDE

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Genie Système d'ouverture de porte

Genie

Genie GCL OPGSX Series Manuel utilisateur

Manuels Système d'ouverture de porte populaires d'autres marques

Pamex

Pamex KT-INP35 Manuel utilisateur

Label

Label NEPTIS/LE Manuel utilisateur

Cal-Royal

Cal-Royal N-F77CVR Manuel utilisateur

Scrigno

Scrigno OPEN1000 Manuel utilisateur

TriMark

TriMark UM 34 Manuel utilisateur

BFT

BFT WIND RMB 130B 200 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Besam

Besam Swingmaster MP Mode d’emploi

CRL

CRL SENIOR PRIMA Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 1431 Series Manuel utilisateur

GAL

GAL MOVFR Fiche technique

Olide

Olide 120B Manuel utilisateur

Normstahl

Normstahl IDO7 Manuel utilisateur

Häfele

Häfele Finetta T 70 VF Manuel utilisateur

AGS

AGS D-PL Manuel

Stanley

Stanley MA900ñ Instructions d'installation

WITTUR

WITTUR Hydra Plus UD300 Manuel

Alutech

Alutech TR-3019-230E-ICU Instructions d'installation et d'utilisation