Genexis DRG488 Manuel utilisateur

User manual

DRG488

Content

1. DRG488 overview

2. Installation of the DRG488

4. Connecting the DRG488

Box content:

• DRG488 product

• Four (4) self-adhesive footpads

• Two angle brackets

• Six (6) screws

• Power adapter

• DRG488 user manual

LED & button functionality

LED Activity Description

Power Green

Flashing

Red

Power is on and boot completed

DRG488 is booting

Hardware error

Uplink Green

Yellow

1000M WAN link established*

100/10M WAN link established*

LAN Green

Yellow

1000M link*

100/10M link*

1. DRG488 overview

*blink on activity

User interfaces

Interface Description

1 WAN port

2 Ethernet LAN ports

3 Power connector

4 SFP port

5 LAN LEDs

6 Power LED

7 Uplink LED

8 Reset pinhole

Reset Button Description

Reboot

Factory

default

Press reset button for less than

5 seconds and release to initiate

reset.

Press and hold reset button for

more than 5 seconds (when LEDs

will blink) and release to initiate

a factory reset. All configuration

data will be lost!

1 2

468

2. DRG488 installation

Option A: Placing the DRG on your desktop

To protect any surface that the DRG is standing

on, there are four rubber pads that need to be

attached.

1. Peel the protective paper from the rubber

pads to expose the adhesive side.

2. Press each of the pads on the bottom of the

DRG casing, as shown below.

3. Place the DRG on your desktop

Step 1: Select a suitable location for the DRG

Before installing the DRG, ensure your working

environment meets the minimum operating require-

ments of the equipment.

Characteristics Requirements

Temperature Between 0 and 45 degrees

Celcius

Operating

Humidity

Max. relative humidity of 90%,

non-condensing

Ventilation Minimum 10 centimeters on

all sides for cooling. If in a

closet, ensure there is ade-

quate airflow.

Step 2: Placement options

The DRG488 installation kit provides parts that

allow you to place the DRG in various locations.

Select the procedure best suited to your operating

environment:

Option B: Mounting the DRG on the wall

To mount the DRG directly on a wall, ensure that

the location is not next to electrical power cables

or gas/water pipes.

1. Drill the necessary holes in the wall for sup-

porting the DRG. The fixing-screw positions

are shown below. A drilling template is pro-

vided as separate download from the Genexis

website.

2. Insert and tighten the mounting screws in the

holes in the wall with the screw head approx.

2mm from the wall.

3. Position the DRG in such a way that each

screw head is aligned with a mounting screw

hole.

4. Push the DRG onto the screw heads and slide

gently downwards until the screws lock the

DRG firmly into position.

Option C: Mounting the DRG with brackets

If the DRG is to be securely installed, for example

in a cabinet, angle brackets are supplied to mount

the DRG horizontally or vertically.

1. Attach both angle brackets to the screw holes

on the side of the DRG488, using the supplied

screws.

2. Mount the DRG488 in the cabinet or on a

rack, using the appropriate screws.

PWR

1234

Uplink

5678

10/100/1000 Mbps

PWR

1234

Uplink

5678

10/100/1000 Mbps

3. Connecting the DRG488

Step 1: Connecting to the network

Depending on the way you would like to connect

the DRG488 to the broadband network (fiber SFP or

copper WAN), different cables are used.

Using the Copper uplink

Use a RJ-45 Cat 5e Ethernet cable to connect the

DRG488 to the broadband network socket by push-

ing the cable connector gently, but firmly into the

‘WAN’ port until it locks.

Using the SFP fiber uplink

Use a fiber patch cable to connect the DRG488 to

the broadband network by gently pushing the fiber

connector into the ‘SFP’ module (Ensure that an

MSA-compliant SFP module is properly installed in

the SFP port).

Step 2: Connecting a device to the DRG488

Locate a free Ethernet LAN port for your device (see

chapter 1) and push the RJ-45 Ethernet connector

of your device gently into the DRG488 LAN port

until it locks.

Step 3: Powering the DRG488

1. Connect the power cable from the power

adapter (as delivered with the DRG488) to the

DRG ‘power’ port.

2. Connect the power adapter to a main power

outlet.

3. The power LED will now light up. The

power LED remains lit while the product is

connected.

Note:

If the power LED does not light up and there

is no obvious problem, please contact the

supplier of your network connection.

Europe-EU Declaration of Conformity

Hereby, Genexis BV declares that this product is in compliance

with the essential requirements and other relevant provisions

of Directive 1999/5/EC.

Table des matières

Autres manuels Genexis Routeur réseau

Genexis

Genexis FiberTwist P3000B Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis FiberTwist P6426 Manuel utilisateur

Genexis

Genexis OCG-218m Instructions d'utilisation et d'installation

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis Aura Series Manuel utilisateur

Genexis

Genexis FiberTwist G2420 Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis XG Series Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis FiberTwist P2410 Manuel utilisateur

Genexis

Genexis DRG700 Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Genexis

Genexis Pure Series Manuel utilisateur

Genexis

Genexis FiberTwist Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité