Genexis FiberTwist Manuel utilisateur
FiberTwist
Network Termination
ii
Quick Installation Guide ....................................................................1
Schnellinstallationsanleitung............................................................13
FiberTwist
Network Termination
Quick Installation Guide
2
In the box
Model: Fibertwist-X0000
PN: 996160001
SN: Z.000001001
CLASS 1
LASER PRODUCT
+12v 0.5A
2016-05 VER.1.0
Made in India
GPON SN:GNXS01000001
FiberTwist
Active device
(exact appearance differs depending on the model)
Label
Please retain for future reference.
Power Adaptor
Use only the supplied power adaptor.
Model
G2110
G2120
P2110
P2410, P3410,
G2410
P2420, P3420,
G2420
Models Supported
4
Overview (side)
Unlock button: press and hold while twisting to the left to
remove the FiberTwist or blind cover from the FTU (ber
termination unit).
Reset button: *
• press and release to reset (retain custom settings)
• press and hold for more than 5 seconds to perform a factory
reset (deletes all custom conguration)
Dim button: dims the lights on the device as described below.
* On some models, the reset button is on the end of the device next to the power
connector. Not present on the P2110.
Dim button behaviour (all models)
Each press of the dim button cycles through the following sequence of
brightness levels:
fully lit offhalf lit
(not on the P2110)
Overview (end)
CATV * LAN ports power connector
Point to Point Series
power switch
power connector
reset button
LAN port
GPON series
* not present on all models
6
Installation
1. Preparation
Ensure there is a power socket within 80cm of where the device is being
installed.
Open the FiberTwist box (but don’t yet remove the FiberTwist from the box)
and place the box near where the FiberTwist is to be installed.
Important: It is crucial the following steps all be completed
in one go. Failure to do so could result in damage to the
bre optic connectors, causing a severe degradation of
signal quality.
2. Remove the blind cover (if present)
Press and hold the unlock button.
Rotate the blind cover counter-
clockwise (in the direction of
the arrow).
When it won’t rotate any
further, the blind cover can be
removed.
Please store the blind cover in a safe place.
8
3. Remove dust cap
Take the FiberTwist out of its box.
The dust cap is the bright red tab located on the rear of the FiberTwist
(pictured below).
Remove the dust cap by holding the end of the red tab and pulling it gently
in the direction of the arrow.
Please store the dust cap in a safe place.
Autres manuels pour FiberTwist
1
Table des matières
Langues :
Autres manuels Genexis Accessoires réseau
Manuels Accessoires réseau populaires d'autres marques
Patton electronics
Patton electronics 2888 Manuel utilisateur
Cradlepoint
Cradlepoint COR IBR1100/IBR1150 Manuel utilisateur
Paradyne
Paradyne Hotwire 8620 Manuel utilisateur
Infra Cool
Infra Cool F-1.3 Manuel utilisateur
Edgewater Networks
Edgewater Networks 4300T Manuel utilisateur
Edimax
Edimax SB-2200g Manuel utilisateur
Extreme Networks
Extreme Networks Mogul-100 Manuel utilisateur
Aaeon
Aaeon FWS-8500 Manuel utilisateur
Panduit
Panduit Z11C Series Manuel utilisateur
F5
F5 BIG-IP 10000 Series Instructions de montage
ZyXEL Communications
ZyXEL Communications NMA1115 Manuel utilisateur
Auerswald
Auerswald COMtrexx Business Manuel utilisateur