Genexis FiberTwist Manuel utilisateur
SSID: Genexis-xxxx
WiFi-Key:
**************
WARNING: POWER RATING:12V2A
GUI: http://Genexis-xxxx
Username: user
Password: user
Made in China
Model: Pulse
P/N: 99618025
Version: 1.0
Date: 2018-05
Power switch
FiberTwist + Pulse
Network Termination +
WiFi Repeater/Extender
Quick Installation Guide
www.genexis.eu
Revision 1.3. - September 2018
Copyright © 2018 Genexis B.V. All rights reserved.
7. Connect Pulse to FiberTwist
Connect the provided Ethernet cable to a
LAN port of your FiberTwist and to the WAN
(red) port of your Pulse.
8. Connect to the power
Connect the supplied power adapter to your
Pulse and plug the adapter into an
AC power socket.
9. Turn on your Pulse
Turn on your Pulse by fl ipping the switch on
the side of the device.
After approximately 1.5 minutes the Status
LED should turn green and stop blinking.
When the Internet LED becomes yellow, your
Pulse is ready for use.
10. Connect to your Pulse WiFi
Consult the information label at the bottom
of your Pulse. It shows the SSID of the WiFi
network (i.e. GENEXIS-xxxx) and the WiFi
Key. Connect to this WiFi network with your
devices.
You are now connected to the internet.
For more information about your Pulse
or your FiberTwist, have a look at the Full
Installation Guides (https://genexis.eu/
download-portal/#fi bertwist)or
https://genexis.eu/download-portal/#pulse)
or contact your service provider.
Hereby, Genexis declares that the radio
equipment type Pulse is in compliance with
Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the
following internet address:
https://genexis.eu/red/pulse
Dust cap
Unlock button
1. Preparation
The installation of your FiberTwist and Pulse
combination starts with the FiberTwist.
After installing the FiberTwist, the next steps
of connecting the Pulse can be followed from
step 6.
Ensure there is a power socket within 80cm of
where your FiberTwist is being installed.
Important: It is crucial the next steps for
the installation of your FiberTwist all be
completed in one go. Failure to do so
could result in damage to the ber optic
connectors, causing a severe degradation
of signal quality. It is assumed that the Fiber
Termination Unit (FTU) is already installed in
the meter cabinet or mounted on a wall.
2. Remove the FTU blind cover
• Press and hold the unlock button (on the
right side at the top of the blind cover).
• Rotate the blind cover counter clockwise.
• When it won’t rotate any further,
the blind cover can be removed by
pulling it towards you.
• Please store the blind cover in a safe place.
3. Remove dust cap of FiberTwist
Take your FiberTwist out of its box. The dust
cap is the bright red tab located on the rear
of your FiberTwist.
Remove the dust cap by holding the end
of the red tab and pulling it gently in the
direction of the arrow.
Please store the dust cap (along with the
blind cover) in a safe place.
4. Twist!
Place your FiberTwist on the FTU as shown
above and rotate clockwise until it clicks
into place.
Make sure your FiberTwist is aligned squarely
on the FTU - each edge must line up directly
with the FTU below.
Note:
If at some point in the future it becomes
necessary to uninstall your FiberTwist, please
place the blind cover back on the FTU
immediately and put the dust cap back on
your FiberTwist.
6. Placement of Pulse
Place your Pulse within 2m* from your
FiberTwist, preferably not in the
meter cabinet.
Ensure there is a power socket within 1m of
where your Pulse is being installed.
Your Pulse can be placed on a desk, or it can
be mounted on a wall using the wall mount
points on the back of the device.
The Drilling Template can be downloaded
from the Genexis website at:
https://genexis.eu/download-portal/#pulse
5. Connect to the power
Connect the supplied power adaptor to your
FiberTwist and then plug the adaptor into a
power socket.
*2m Ethernet cable is included. Depending
on your home, a longer cable can be used to
place the Pulse further into the home.
Dust cap
Unlock button
1. Preparation
The installation of your FiberTwist and Pulse
combination starts with the FiberTwist.
After installing the FiberTwist, the next steps
of connecting the Pulse can be followed from
step 6.
Ensure there is a power socket within 80cm of
where your FiberTwist is being installed.
Important: It is crucial the next steps for
the installation of your FiberTwist all be
completed in one go. Failure to do so
could result in damage to the ber optic
connectors, causing a severe degradation
of signal quality. It is assumed that the Fiber
Termination Unit (FTU) is already installed in
the meter cabinet or mounted on a wall.
2. Remove the FTU blind cover
• Press and hold the unlock button (on the
right side at the top of the blind cover).
• Rotate the blind cover counter clockwise.
• When it won’t rotate any further,
the blind cover can be removed by
pulling it towards you.
• Please store the blind cover in a safe place.
3. Remove dust cap of FiberTwist
Take your FiberTwist out of its box. The dust
cap is the bright red tab located on the rear
of your FiberTwist.
Remove the dust cap by holding the end
of the red tab and pulling it gently in the
direction of the arrow.
Please store the dust cap (along with the
blind cover) in a safe place.
4. Twist!
Place your FiberTwist on the FTU as shown
above and rotate clockwise until it clicks
into place.
Make sure your FiberTwist is aligned squarely
on the FTU - each edge must line up directly
with the FTU below.
Note:
If at some point in the future it becomes
necessary to uninstall your FiberTwist, please
place the blind cover back on the FTU
immediately and put the dust cap back on
your FiberTwist.
6. Placement of Pulse
Place your Pulse within 2m* from your
FiberTwist, preferably not in the
meter cabinet.
Ensure there is a power socket within 1m of
where your Pulse is being installed.
Your Pulse can be placed on a desk, or it can
be mounted on a wall using the wall mount
points on the back of the device.
The Drilling Template can be downloaded
from the Genexis website at:
https://genexis.eu/download-portal/#pulse
5. Connect to the power
Connect the supplied power adaptor to your
FiberTwist and then plug the adaptor into a
power socket.
*2m Ethernet cable is included. Depending
on your home, a longer cable can be used to
place the Pulse further into the home.
Dust cap
Unlock button
1. Preparation
The installation of your FiberTwist and Pulse
combination starts with the FiberTwist.
After installing the FiberTwist, the next steps
of connecting the Pulse can be followed from
step 6.
Ensure there is a power socket within 80cm of
where your FiberTwist is being installed.
Important: It is crucial the next steps for
the installation of your FiberTwist all be
completed in one go. Failure to do so
could result in damage to the ber optic
connectors, causing a severe degradation
of signal quality. It is assumed that the Fiber
Termination Unit (FTU) is already installed in
the meter cabinet or mounted on a wall.
2. Remove the FTU blind cover
• Press and hold the unlock button (on the
right side at the top of the blind cover).
• Rotate the blind cover counter clockwise.
• When it won’t rotate any further,
the blind cover can be removed by
pulling it towards you.
• Please store the blind cover in a safe place.
3. Remove dust cap of FiberTwist
Take your FiberTwist out of its box. The dust
cap is the bright red tab located on the rear
of your FiberTwist.
Remove the dust cap by holding the end
of the red tab and pulling it gently in the
direction of the arrow.
Please store the dust cap (along with the
blind cover) in a safe place.
4. Twist!
Place your FiberTwist on the FTU as shown
above and rotate clockwise until it clicks
into place.
Make sure your FiberTwist is aligned squarely
on the FTU - each edge must line up directly
with the FTU below.
Note:
If at some point in the future it becomes
necessary to uninstall your FiberTwist, please
place the blind cover back on the FTU
immediately and put the dust cap back on
your FiberTwist.
6. Placement of Pulse
Place your Pulse within 2m* from your
FiberTwist, preferably not in the
meter cabinet.
Ensure there is a power socket within 1m of
where your Pulse is being installed.
Your Pulse can be placed on a desk, or it can
be mounted on a wall using the wall mount
points on the back of the device.
The Drilling Template can be downloaded
from the Genexis website at:
https://genexis.eu/download-portal/#pulse
5. Connect to the power
Connect the supplied power adaptor to your
FiberTwist and then plug the adaptor into a
power socket.
*2m Ethernet cable is included. Depending
on your home, a longer cable can be used to
place the Pulse further into the home.
SSID: Genexis-xxxx
WiFi-Key:
**************
WARNING: POWER RATING:12V2A
GUI: http://Genexis-xxxx
Username: user
Password: user
Made in China
Model: Pulse
P/N: 99618025
Version: 1.0
Date: 2018-05
Power switch
FiberTwist + Pulse
Network Termination +
WiFi Repeater/Extender
Quick Installation Guide
www.genexis.eu
Revision 1.3. - September 2018
Copyright © 2018 Genexis B.V. All rights reserved.
7. Connect Pulse to FiberTwist
Connect the provided Ethernet cable to a
LAN port of your FiberTwist and to the WAN
(red) port of your Pulse.
8. Connect to the power
Connect the supplied power adapter to your
Pulse and plug the adapter into an
AC power socket.
9. Turn on your Pulse
Turn on your Pulse by fl ipping the switch on
the side of the device.
After approximately 1.5 minutes the Status
LED should turn green and stop blinking.
When the Internet LED becomes yellow, your
Pulse is ready for use.
10. Connect to your Pulse WiFi
Consult the information label at the bottom
of your Pulse. It shows the SSID of the WiFi
network (i.e. GENEXIS-xxxx) and the WiFi
Key. Connect to this WiFi network with your
devices.
You are now connected to the internet.
For more information about your Pulse
or your FiberTwist, have a look at the Full
Installation Guides (https://genexis.eu/
download-portal/#fi bertwist)or
https://genexis.eu/download-portal/#pulse)
or contact your service provider.
Hereby, Genexis declares that the radio
equipment type Pulse is in compliance with
Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the
following internet address:
https://genexis.eu/red/pulse
SSID: Genexis-xxxx
WiFi-Key:
**************
WARNING: POWER RATING:12V2A
GUI: http://Genexis-xxxx
Username: user
Password: user
Made in China
Model: Pulse
P/N: 99618025
Version: 1.0
Date: 2018-05
Power switch
FiberTwist + Pulse
Network Termination +
WiFi Repeater/Extender
Quick Installation Guide
www.genexis.eu
Revision 1.3. - September 2018
Copyright © 2018 Genexis B.V. All rights reserved.
7. Connect Pulse to FiberTwist
Connect the provided Ethernet cable to a
LAN port of your FiberTwist and to the WAN
(red) port of your Pulse.
8. Connect to the power
Connect the supplied power adapter to your
Pulse and plug the adapter into an
AC power socket.
9. Turn on your Pulse
Turn on your Pulse by fl ipping the switch on
the side of the device.
After approximately 1.5 minutes the Status
LED should turn green and stop blinking.
When the Internet LED becomes yellow, your
Pulse is ready for use.
10. Connect to your Pulse WiFi
Consult the information label at the bottom
of your Pulse. It shows the SSID of the WiFi
network (i.e. GENEXIS-xxxx) and the WiFi
Key. Connect to this WiFi network with your
devices.
You are now connected to the internet.
For more information about your Pulse
or your FiberTwist, have a look at the Full
Installation Guides (https://genexis.eu/
download-portal/#fi bertwist)or
https://genexis.eu/download-portal/#pulse)
or contact your service provider.
Hereby, Genexis declares that the radio
equipment type Pulse is in compliance with
Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the
following internet address:
https://genexis.eu/red/pulse
Autres manuels pour FiberTwist
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Genexis Accessoires réseau
Manuels Accessoires réseau populaires d'autres marques
Patton electronics
Patton electronics 2888 Manuel utilisateur
Cradlepoint
Cradlepoint COR IBR1100/IBR1150 Manuel utilisateur
Paradyne
Paradyne Hotwire 8620 Manuel utilisateur
Infra Cool
Infra Cool F-1.3 Manuel utilisateur
Edgewater Networks
Edgewater Networks 4300T Manuel utilisateur
Edimax
Edimax SB-2200g Manuel utilisateur
Extreme Networks
Extreme Networks Mogul-100 Manuel utilisateur
Aaeon
Aaeon FWS-8500 Manuel utilisateur
Panduit
Panduit Z11C Series Manuel utilisateur
F5
F5 BIG-IP 10000 Series Instructions de montage
ZyXEL Communications
ZyXEL Communications NMA1115 Manuel utilisateur
Auerswald
Auerswald COMtrexx Business Manuel utilisateur