Generac Power Systems 2000PSI Manuel utilisateur
2000PSI
This symbol points out important safety instructions, which, if not followed, could
endanger the personal safety and/or property of yourself and others. Read and follow all
instructions in the manual before attempting to operate this unit.
Model No. 1040 3 (2000 PSI High Pressure Washer) Manual No. B4561 Revision 0 (4/12/1999)
Owner’s Manual
Problems?
Questions?
Before taking your unit
back to the store,
call the pressure washer
helpline at
1-800-270-1408
M-F 8-5 CT
GENERAC
The Reliable Ones
2
Generac Portable Products 2000 PSI High Pressure Washer
SAFETY RULES
DANGER! Always disconnect spark plug
wire and place wire where it cannot
contact spark plug to prevent accidental
starting when setting up, transporting,
ad usting or making repairs to your high
pressure washer.
Engine exhaust gases contain DEADLY carbon
monoxide gas. This dangerous gas, if breathed
in sufficient concentrations, can cause
unconsciousness or even death. Operate this
equipment only in the open air where adequate
ventilation is available.
Gasoline is highly FLAMMABLE and its vapors
are EXPLOSIVE. Do not permit smoking, open
flames, sparks or heat in the vicinity while
handling gasoline. Avoid spilling gasoline on a
hot engine. Allow unit to cool for 2 minutes
before refueling. Comply with all laws
regulating storage and handling of gasoline.
Locate this pressure washer in areas away
from combustible materials, combustible fumes
or dust.
The high pressure equipment is designed to be
used with Generac authorized parts only. If you
use this equipment with parts that do not
comply with minimum specifications, the user
assumes all risks and liabilities.
Some chemicals or detergents may be harmful
if inhaled or ingested, causing severe nausea,
fainting or poisoning. The harmful elements
may cause property damage or severe in ury.
Do not allow CHILDREN to operate the
Pressure Washer at any time.
Operate engine only at governed speed.
Running the engine at excessive speeds
increases the hazard of personal in ury. Do not
tamper with parts which may increase or
decrease the governed speed.
Do not wear loose clothing, ewelry or anything
that may be caught in the starter or other
rotating parts.
Before starting the Pressure Washer in cold
weather, check all parts of the equipment and
be sure ice has not formed there.
Units with broken or missing parts, or without
protective housing or covers should NEVER be
operated.
The muffler and air cleaner must be installed
and in good condition before operating the
Pressure Washer. These components act as
spark arrestors if the engine backfires.
Check the fuel system for leaks or signs of
deterioration such as chafed or spongy hose,
loose or missing clamps or damaged tank or
cap. Correct all defects before operating the
Pressure Washer.
Do not spray flammable liquids.
Never aim the gun at people, animals or
plants.
High pressure spray can cause paint chips or
other particles to become airborne and fly at
high speeds.
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects, or other reproductive harm.
WARNING:
IMPORTANT! SAFETY RULES IMPORTANT!
3
Generac Portable Products 2000 PSI High Pressure Washer
Never allow any part of the body to come in
contact with the fluid stream. DO NOT come in
contact with a fluid stream created by a leak in
the high pressure hose.
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious in ury
and possible amputation.
Always wear eye protection when you use this
equipment or when you are in the vicinity
where the equipment is in use.
Never move the machine by pulling on the high
pressure hose. Use the handle provided on the
top of the unit.
Always be certain the spray gun, nozzles and
accessories are correctly attached.
Never use a spray gun that does not have a
trigger lock or trigger guard in place and in
working order.
Use a respirator or mask whenever there is a
chance that vapors may be inhaled. Read all
instructions with mask so you are certain the
mask will provide the necessary protection
against inhaling harmful vapors.
High pressure spray may damage fragile items
including glass. Do not point spray gun at glass
when in the et spray mode.
Keep all hoses connected to pressure washer
and the spray gun while the system is
pressurized. Disconnecting the hoses while the
unit is pressurized is dangerous.
Hold the spray gun firmly in your hand before
you start the unit. Failure to do so could result
in an in ury from a whipping spray gun. Do not
leave the spray gun unattended while the
machine is running.
The cleaning area should have adequate
slopes and drainage to reduce the possibility of
a fall due to slippery surfaces.
Keep water spray away from electric wiring or
fatal electric shock may result.
Do not secure gun trigger in the pullback
(open) position.
Do not bypass any safety device on this
machine.
The muffler and engine heat up during
operation and remain hot immediately after
shutting it down. Avoid contact with a hot
muffler or engine or you could be severely
burned.
Operate and store this unit on a stable surface.
High pressure hose can develop leaks from
wear, kinking, abuse, etc. Water spraying from
a leak is capable of in ecting material into
skin. Inspect hose each time before using it.
Check all hoses for cuts, leaks, abrasions or
bulging of cover, or damage or movement of
couplings. If any of these conditions exist,
replace hose immediately. Never repair high
pressure hose. Replace it with another hose
that meets maximum pressure rating of your
pressure washer.
IMPORTANT! SAFETY RULES IMPORTANT!
4
Generac Portable Products 2000 PSI High Pressure Washer
CONGRATULATIONS on your purchase of a
GENERAC high pressure washer. It has been
designed, engineered and manufactured to give you
the best possible dependability and performance.
Should you experience any problem you cannot
easily remedy, please contact your nearest
GENERAC Authorized Service facility, or call the
1800 number listed on the front of this manual. We
have competent, welltrained technicians and the
proper tools to service or repair this unit.
Please read and retain this manual. The instructions
will enable you to assemble and maintain your high
pressure washer properly.
CUSTOMER
RESPONSIBILITIES
Read and observe the safety rules.
Follow regular schedule in maintaining, caring for
and using your high pressure washer.
Follow the instructions under Customer
Responsibilities and Storage sections of this
Owner's Manual.
PRODUCT
SPECIFICATIONS
Pressure Washer Specifications
Outlet Pressure . . . . 2000 psi
Flow Rate . . . . . . . . . 2.0 gallons per minute (gpm)
Detergent Mix . . . . . . Use undiluted detergent
approved for pressure
washers
Water Supply . . . . . . Not to Exceed 140°F
Temperature
Automatic Cool . . . . Will cycle when water
Down System reaches 140°-145°F
Engine Specifications
Engine Model . . . . . . Briggs & Stratton Quantum
Rated Horsepower . . 6.0
Displacement . . . . . . 190cc
Spark Plug
Type . . . . . . . . RJ19LM
Set Gap To: . . 0.030 inch (0.76mm)
Gasoline Capacity . . 1.6 U.S. quarts
Oil . . . . . . . . . . . . . . . SAE 30
In the State of California a spark arrestor is required
by law (Section 4442 of the California Public
Resources Code). Other states may have similar
laws. Federal laws apply on federal lands.
NOTE: If you equip the engine of your pressure
washer with a spark arrestor muffler, the spark
arrestor must be maintained in effective working order
by the owner/operator.
You can order a spark arrestor through your
authorized Briggs & Stratton service facility. See
Engine Owners Manual for part number.
5
Generac Portable Products 2000 PSI High Pressure Washer
Spray Gun
Adjustable Nozzle
Extension
High Pressure Hose
Goggles
Air Cleaner
Gas Tank
Water Inlet
Pump equipped with
Automatic Cool Down System
Recoil Starter
High Pressure Outlet
Oil Fill Tube
Adjustable Nozzle Extension You must attach this
to the spray gun to provide high pressure stream. The
ad ustable nozzle allows you to ad ust the spray pattern
which, in turn, ad usts the force of spray.
Air Cleaner Dry type filter element limits the amount
of dirt and dust that gets in the engine.
Automatic Cool Down System Cycles water
through pump when water reaches 140°-145°F. Warm
water will discharge from pump onto ground. This
system prevents internal pump damage.
Gas Tank Fill with regular unleaded gasoline only.
Goggles Always use the enclosed goggles or other
eye protection when running your pressure washer.
High Pressure Hose Connect one end to water
pump and the other end to spray wand.
High Pressure Outlet Connection for high pressure
hose.
Oil Fill Tube Fill engine with oil here. See page 7 for
oil recommendations.
Pump Develops high pressure.
Recoil Starter Used for starting the engine
manually.
Spray Gun Controls the application of water onto
cleaning surface with trigger device. Includes safety
latch.
Water Inlet Connection for garden hose.
KNOW YOUR PRESSURE WASHER
Read this owners manual and safety rules before operating your high pressure washer.
Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various
controls and ad ustments. Save this manual for future reference.
6
Generac Portable Products 2000 PSI High Pressure Washer
Read entire owners manual before you attempt to
assemble or operate your new pressure washer. Your
new pressure washer has been assembled at the
factory with the exception of those parts left
unassembled for shipping purposes.
REMOVE PRESSURE
WASHER FROM CARTON
Remove parts box included with pressure washer.
Slice two corners at guide handle end of carton
from top to bottom so the panel can be folded down
flat, then remove all packing material.
Roll pressure washer out of carton.
CARTON CONTENTS
Items in the carton include:
Main Unit
Parts Box (which includes the following):
Wireform
ORing Maintenance Kit.
Goggles
Nozzle Cleaning Kit
Owners Manual
Engine Manual
Spray Gun
Nozzle Extension
High Pressure Hose
Handle
Bottle of Oil
Owners Registration Card
Parts Bag (which includes the following):
1 carriage bolt
1 carriage hook
2 knobs
If any of the above parts are missing or damaged, call
the pressure washer helpline at 1 800 270 1408.
PREPARING PRESSURE
WASHER FOR USE
If you have any problems with the assembly of your
pressure washer or if parts are missing or damaged,
call the Pressure Washer Helpline at 1-800-270-1408.
To prepare your pressure washer for operation you
will need to perform these tasks:
Attach the handle and the wire form that holds high
pressure hose and spray gun.
Connect high pressure hose to the spray gun and
the pump, and connect water supply to the pump.
Add oil to engine crankcase.
Add fuel to fuel tank.
Attach the Handle
Place the top of the handle onto the bottom of the
handle already connected to the main unit making
sure the holes in the top align with the holes on the
bottom (Figure 1).
Figure 1 Attach the top of the handle to the bottom of
the handle.
Make sure the
holes on the
top of the
handle are
aligned with the
holes in the
bottom of the
handle
7
Generac Portable Products 2000 PSI High Pressure WasherGenerac Portable Products 2000 PSI High Pressure Washer
Insert the carriage bolt through the right hole
(looking at the front of the pressure washer) and
attach a plastic knob. Tighten the knob by hand
(Figure 2).
Insert the carriage hook through the left hole
(looking at the front of the pressure washer). Pull
the recoil handle out slowly. Place the recoil string
through the hook and attach the plastic knob.
Tighten the knob by hand (Figure 2).
Insert the wire form with the longer arm positioned on
the left. From this view (from rear of unit) the hook
should resemble a J
(Figure 3)
.
Add Engine Oil
IMPORTANT: Any attempt to crank or start the engine
before it has been properly serviced with the
recommended oil may result in an engine failure.
Note: When adding oil to the engine crankcase, use
only high quality detergent oil rated with API service
classification SF,SG, SH or SH/CD rated SAE 30
weight.
Select the oils viscosity grade according to your
expected operating temperature:
Do Not Use SAE 10W40 Oil.
Although multiviscosity oils (5W30, 10W30, etc.)
improve starting in cold weather, these multiviscosity
oils will result in increased oil consumption when used
above 32°F. Check your engine oil level more
frequently to avoid possible damage from running low
on oil.
Place pressure washer on a level surface.
Clean area around oil fill and remove oil dipstick
(Figure 4).
Wipe dipstick clean. Pour oil into oil fill opening until
oil reaches FULL mark on the dipstick. Stop
occasionally to check oil level. DO NOT OVERFILL.
Install oil dipstick, hand tighten securely.
Note: Check Oil Often During Engine Break in.
Figure 3 Fit wire form on handle.
Figure 4 Add oil to engine crankcase. Do not attempt
to start engine without adding oil.
Oil Fill Cap
Figure 2 Insert the carriage bolt and hook and attach
the knobs.
colder 32°F warmer
5W30 SAE 30
8
Generac Portable Products 2000 PSI High Pressure Washer
Add Gasoline
DANGER! Never fill fuel tank indoors. Never
fill fuel tank when engine is running or hot. Do
not smoke when filling fuel tank.
WARNING! Never fill fuel tank completely
full. Fill tank to about 1/2" below the bottom of
the filler neck to provide space for fuel
expansion. Wipe away any fuel spillage from
engine and equipment before starting.
The manufacturer recommends fresh, clean unleaded
automotive gasoline.
Use clean fuel and store in approved, clean,
covered containers. Use clean fill funnels. Never
use stale gasoline left over from last season or
gasoline stored for long periods.
Clean area around fuel fill cap, remove cap.
(Figure 5).
Add UNLEADED regular gasoline, slowly, to fuel
tank. Use a funnel to prevent spillage.
Install fuel cap and wipe up any spilled gasoline.
Connect Hose and Water Supply
to Pump
IMPORTANT: You must assemble wand and attach
all hoses before you start engine. Starting engine
without all hoses connected and water supplied will
damage pump.
Uncoil high pressure hose and attach one end of
hose to the base of the spray gun (Figure 6).
Tighten by hand.
Attach other end of high pressure hose to the high
pressure outlet on the pump (Figure 7). Tighten by
hand.
Before you connect your garden hose to the water
inlet, inspect the Inlet Screen (Figure 8). Clean the
screen if it contains debris or have it replaced if
damaged. Do not run the pressure washer if the
inlet screen is damaged.
Connect garden hose to water inlet. Tighten by
hand (Figure 8).
Figure 7 Connect high pressure hose to pump.
Figure 6 Connect high pressure hose to spray gun.
Figure 5 Add gasoline to fuel tank.
Fuel Cap
9
Generac Portable Products 2000 PSI High Pressure Washer
Turn ON the water (open valve completely).
Squeeze trigger on gun to purge pump system of
air and impurities.
CAUTION! Before starting the pressure
washer, be sure you are wearing adequate
eye protection.
Attach nozzle extension to spray gun. Tighten by
hand (Figure 9).
CHECKLIST BEFORE
STARTING ENGINE
Look back over the assembly to see if you have
performed all of the following:
Check for properly tightened hose connections
(high pressure and water supply) and for tight
connections and that there are no kinks, cuts, or
damage to the high pressure hose.
Check that oil has been added to proper level in
engine crankcase before trying to start the pressure
washer.
Add proper gasoline to fuel tank.
Provide proper water supply (not to exceed 140°F).
Be sure to read Safety Rules and Operation
sections before using the pressure washer.
Figure 9 Connect nozzle extension to spray gun.
Figure 8 Connect the garden hose to water inlet and
turn ON the water.
Check Screen for Damage
10
Generac Portable Products 2000 PSI High Pressure Washer
HOW TO USE YOUR
PRESSURE WASHER
If you have any problems operating your pressure
washer, please call the pressure washer helpline at
1-800-270-1408.
You have assembled your high pressure washer and
have prepared the engine for starting. You are now
ready to clean your car, boat or the outside of a
building or whatever you plan to clean.
How to Start Your Engine
The best way to start your enginepowered pressure
washer for the first time is to follow these instructions
stepbystep. This starting information also applies
whenever you start the engine after you have let the
pressure washer sit idle for at least a day.
This pressure washer requires a water source that
flows at least 2.5 gallons per minute. Do not
attempt to siphon water from a non pressurized
container. Place the pressure washer close
enough to an outside water source so that no more
than 50' of garden hose is needed.
Check that the high pressure hose is tightly
connected to the spray gun and to the pump. See
ASSEMBLY section for illustrations.
Connect the garden hose to water inlet on the
pressure washer pump and turn the water on all
the way.
IMPORTANT: Do not run pump without the water
supply connected and turned on. You must follow this
caution or the pump will be damaged.
Squeeze the trigger on the spray gun to relieve air
pressure caused by turning ON the water. Water
will spew out the gun in a thin stream. Continue to
hold trigger until you have a steady stream of water
and no air remains.This will make it easier to pull
start the engine. Release the trigger.
Apply the safety latch to the spray gun trigger
(Figure 10).
Move the Throttle Control Lever to the Fast
position.
Set Choke Lever to Choke position.
Note: This is a multiposition choke.
Note: For a warm engine, be sure the Throttle Control
Lever is in the Fast position and the Choke Lever is
in the Run position.
Grasp rope handle and pull slowly until you feel
some resistance. Then pull cord rapidly to
overcome compression, prevent kickback and start
the engine. Let rope return to starter slowly.
Note: Always keep the Throttle Control Lever in the
Fast position when operating the pressure washer.
When the engine starts, gradually move the Choke
Lever from one position to the next until it is in the
Run position.
If after 3 pulls the engine fails to start, disengage the
spray gun safety latch, squeeze the trigger to relive
water pressure, reengage the spray gun safety latch,
move the Choke Lever to the Run position and pull
the recoil starter handle rapidly (Max. 3 pulls).
How to Stop Your Pressure
Washer
Move the Throttle Control Lever to the Slow position.
Wait for the engine to idle down.
Move the Throttle Lever Lever to the Stop position.
Simply shutting off the engine will not release
pressure in the system. Squeeze trigger on the
spray gun to relieve pressure in the hose.
Note: A small amount of water will squirt out when
you release the pressure.
Figure 10 Squeeze trigger to relieve water pressure,
release trigger and turn the safety latch
ON.
Safety Latch ON
Autres manuels pour 2000PSI
2
Autres manuels Generac Power Systems Nettoyeur haute pression
Generac Power Systems
Generac Power Systems 1043-2 Manuel utilisateur
Generac Power Systems
Generac Power Systems 6000CP Manuel utilisateur
Generac Power Systems
Generac Power Systems 1173-1 Manuel utilisateur
Generac Power Systems
Generac Power Systems 6020-2 Manuel utilisateur
Generac Power Systems
Generac Power Systems 1292-2 Manuel utilisateur
Generac Power Systems
Generac Power Systems 3000PSI Manuel utilisateur
Generac Power Systems
Generac Power Systems 1037-0 Manuel utilisateur
Generac Power Systems
Generac Power Systems Power Washer Manuel utilisateur
Generac Power Systems
Generac Power Systems 1455-0 Manuel utilisateur
Generac Power Systems
Generac Power Systems 2700PSI 1676-0 Manuel utilisateur
Generac Power Systems
Generac Power Systems 1700PSI Manuel utilisateur
Generac Power Systems
Generac Power Systems 1195-0 Manuel utilisateur
Generac Power Systems
Generac Power Systems 1537-0 Manuel utilisateur
Generac Power Systems
Generac Power Systems Power Washer Manuel utilisateur
Generac Power Systems
Generac Power Systems 1420-0 Manuel utilisateur
Generac Power Systems
Generac Power Systems 006022-0 Manuel utilisateur
Generac Power Systems
Generac Power Systems Power Washer Manuel utilisateur
Generac Power Systems
Generac Power Systems 1292-2 Manuel utilisateur
Generac Power Systems
Generac Power Systems 1600PSI Manuel utilisateur
Generac Power Systems
Generac Power Systems OneWASH Manuel utilisateur
