Generac Power Systems Mobile Link Unit Manuel de service

Owner and Installation

Manual

Mobile Link™ Unit

*THIS PRODUCT CAN BE INSTALLED BY THE OWNER. HOWEVER, IF

UNCOMFORTABLE WITH THE SKILLS OR TOOLS REQUIRED, THE

MANUFACTURER RECOMMENDS TO HAVE A QUALIFIED ELECTRICIAN

OR CONTRACTER PERFORM THE INSTALLATION.

This manual should remain with the Mobile Link unit.

FOR INSTALLATION ASSISTANCE CONTACT: 1-855-GEN-VIEW

™

FCC Compliance....................................................1

Section 1: Safety...................................3

1.1: General Safety............................................4

1.2: General Safety Hazards..............................5

1.3: Electrical Hazards.......................................6

1.4: Explosion Hazards......................................7

Section 2: General Information ............8

2.1: Introduction.................................................8

2.2: Applications.................................................8

2.3: Information Screens....................................9

Section 3: Installation..........................12

3.1: Installation.................................................12

Section 4: Actition...............................22

Section 5: Maintenance.......................22

5.1: Cleaning....................................................22

Section 6: Troubleshooting.................23

Section 7: Notes...................................24

Table of Contents

Mobile Link 1

Compliance Statement (Part 15.19)

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference received, including interfer-

ence that may cause undesired operation.

Warning (Part 15.21)

Changes or modifications not expressly approved by the party responsi-

ble for compliance could void the user's authority to operate the equip-

ment.

FCC Interference Statement (Part 15.105 (b))

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful interference to radio com-

munications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

WARNING!

California Proposition 65

This product contains or emits chemicals known to the state of California to cause cancer,

birth defects, and other repoductive harm.

2 Mobile Link

• Consult the dealer or an experienced radio/TV technician for

help.

To comply with FCC/IC RF exposure limits for general population /

uncontrolled exposure, the antenna(s) used for this transmitter must

be installed to provide a separation distance of at least 20 cm from all

persons and must not be co-located or operating in conjunction with

any other antenna or transmitter.

RF Exposure (OET Bulletin 65)

To comply with FCC/IC RF exposure requirements for mobile trans-

mitting devices, this transmitter should only be used or installed at

locations where there is at least 20 cm separation distance between

the antenna and all persons.

Section 7.1.5 of RSS-GEN

Operation is subject to the following two conditions:

1.This device may not cause interference.

2.This device must accept any interference, including interference

that may cause undesired operation of the device.

Please insert the model number of your unit in the space below.

Model No.

Mobile Link 3

Section 1 Safety

INTRODUCTION: Thank you for purchasing this Mobile Link™ unit. With

this remote monitoring system, the status of a generator can be checked

from anywhere the owner has access to an Internet connection from a PC

or while traveling with any smart device. Every effort was made to make

sure that the information and instructions in this manual were both accu-

rate and current at the time the manual was written. However, the manu-

facturer reserves the right to change, alter or otherwise improve this

product or manual at any time without prior notice.

READ THIS MANUAL THOROUGHLY: The operator is responsible for

proper and safe use of this equipment. The manufacturer strongly recom-

mends that the operator read and thoroughly understand the instructions

and contents of this owner’s manual before attempting to use the equip-

ment. If any portion of this publication is not understood, contact the near-

est Authorized Service Dealer for starting, operating and servicing

procedures.

SAVE THESE INSTRUCTIONS: The manufacturer suggests that this

manual and the rules for safe operation be copied and posted near the

unit’s installation site. Safety should be stressed to all operators and

potential operators of this equipment.

SAFETY: Throughout this manual, and on tags and decals affixed to the

unit, DANGER, WARNING, CAUTION and NOTE blocks are used to alert

personnel to special instructions about a particular operation, function or

service that may be hazardous if performed incorrectly or carelessly.

Observe them carefully. Their definitions are as follows:

INDICATES A HAZARDOUS SITUATION OR

ACTION WHICH, IF NOT AVOIDED, WILL

RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action

which, if not avoided, could result in death

or serious injury.

4 Mobile Link

Indicates a hazardous situation which, if

not avoided, could result in minor or

moderate injury.

NOTE: Notes contain additional information important to an

operation or procedure.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each indi-

cates is as follows:

This symbol points out important Safety Informa-

tion that, if not followed, could endanger personal

safety and/or property of others.

This symbol points out a potential Explosion Haz-

ard.

This symbol points out a potential Fire Hazard.

This symbol points out a potential Electrical

Shock Hazard.

These “Safety Alerts” cannot eliminate the hazards that they signal.

Strict compliance with these special instructions, plus common sense,

are major accident prevention measures.

1.1 - General Safety

Study these safety rules carefully before operating or servicing this

equipment. Become familiar with this Owner’s Manual and with the

unit. The unit can operate safely, efficiently and reliably only if it is

properly installed, operated and maintained. Many issues are caused

by failing to follow simple and fundamental rules or precautions.

Mobile Link 5

The manufacturer cannot anticipate every possible circumstance that

might involve a hazard. The warnings in this manual and on tags and

decals affixed to the unit are, therefore, not all-inclusive. If using a proce-

dure, work method or operating technique the manufacturer does not spe-

cifically recommend, ensure that it is safe for personnel. Also make sure

the procedure, work method or operating technique utilized does not ren-

der the generator unsafe.

Despite the safe design of this generator, operating this

equipment imprudently, neglecting its maintenance or

being careless can cause possible injury or death.

Permit only responsible and capable persons to install,

operate and maintain this equipment.

Potentially lethal voltages are generated by these

machines. Ensure steps are taken to make the machine

safe before attempting to work on or near the generator.

Parts of the generator are rotating and/or hot during

operation. Exercise care near a running generator.

The control panel for the generator is intended to

be operated by qualified service personnel only

during Mobile Link installation.

1.2 - General Safety Hazards

• For safety reasons, the manufacturer recommends that this equip-

ment be installed by a Service Dealer or other competent, qualified

electrician or installation technician who is familiar with applicable

codes, standards and regulations. The operator also must comply

with all such codes, standards and regulations. Repair generally

requires simple replacement of the assembly with a new unit, which

can usually be performed by the generator owner.

6 Mobile Link

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

• Before performing any work near the generator, remove the

control panel fuse and disconnect the black (-) battery cable to

prevent accidental startup. When disconnecting battery cables,

always remove the black (-) cable first, then remove the red (+)

cable. When reconnecting the cables, connect the red (+) cable

first, and then black (-) cable.

• Never use the generator or any of its parts as a step. Stepping

on the unit can stress and break parts and may result in dan-

gerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.

• Carbon monoxide poisoning can cause weakness, sleepiness,

inability to think clearly, fainting, unconsciousness or even

death. If any carbon monoxide poisoning symptom is experi-

enced, move to fresh air and immediately seek medical atten-

tion.

• This generator is designed for OUTDOOR installation ONLY.

Never operate the generator inside any garage or other

enclosed space.

1.3 - Electrical Hazards

• All generators produce dangerous electrical voltages that can

cause fatal electrical shock. Utility power delivers extremely

high and dangerous voltages to the transfer switch, as does the

standby generator when it is in operation. Avoid contact with

bare wires, terminals, connections, etc. while the unit is run-

ning. Ensure all appropriate covers, guards and barriers are in

place, secured and/or locked before operating the generator. If

work must be done around an operating unit, stand on an insu-

lated, dry surface to reduce potential shock hazard.

• Do not handle any kind of electrical device while standing in

water, while barefoot or while hands or feet are wet. DANGER-

OUS ELECTRICAL SHOCK MAY RESULT.

Mobile Link 7

• This is an Automatic Standby Generator. The generator may crank

and start at any time when utility is lost. When this occurs, load cir-

cuits are transferred to the STANDBY (generator) power source.

Before working on this generator (for inspection, service or mainte-

nance), to prevent possible injury, always set the generator to the

OFF mode and remove the 7.5A fuse from the generator control

panel.

• In case of an accident caused by electric shock, immediately shut

down the source of electrical power. If this is not possible, attempt

to free the victim from the live conductor. AVOID DIRECT CON-

TACT WITH THE VICTIM. Use a nonconducting implement, such

as a dry rope or board, to free the victim from the live conductor. If

the victim is unconscious, apply first aid and get immediate medical

help.

• Never wear jewelry when working on this equipment. Jewelry can

conduct electricity resulting in electric shock or may get caught in

moving components resulting in injury.

1.4 - Explosion Hazards

• Do not smoke around the generator. Wipe up any fuel or oil spills

immediately. Ensure that no combustible materials are left in the

generator compartment or on or near the generator as FIRE or

EXPLOSION may result. Keep the area surrounding the generator

clean and free from debris.

• Gaseous fluids, such as natural gas and liquid propane (LP) gas,

are extremely EXPLOSIVE. Install the fuel supply system according

to applicable fuel-gas codes. Before placing the home standby

electric system into service, fuel system lines must be properly

purged and leak tested according to applicable code. Inspect the

fuel system periodically for leaks. No leakage can be permitted.

8 Mobile Link

Section 2 General Information

2.1 - Introduction

With this remote monitoring system, the status of the generator can

be checked from anywhere that the owner has access to an Internet

connection from a PC or while traveling with any smart device.

The unit is mounted on the outside of the generator and communi-

cates with the generator’s controller via a serial port. It provides infor-

mation about the generator. When the generator is registered with

www.StandbyStatus.com, the owner can log into this website to

check on the current status of the generator at any time. It will also

notify the owner of any change in operating status. The owner will be

contacted if alarms or warnings occur. When a change in the genera-

tor’s status occurs, an e-mail or text message is sent. The delivery

method and frequency of these alerts can be adjusted on the website.

2.2 - Applications

• This unit can be installed on all 2008 and later air-cooled home

standby units, with an LCD display, and all 2010 and later liq-

uid-cooled gaseous fuel standby units.

•For liquid-cooled units, an additional adapter harness is

required (model 006478-0).

• Suitable for flat surface or surface with a 1355mm radius mini-

mum, mounting in a Type 3R or rainproof enclosure.

• Power supplied by the engine starting battery is limited to 5

Amps DC by a fuse in the Mobile Link unit’s harness. The fuse

is used for overcurrent protection of the Mobile Link unit hard-

ware.

• Maximum ambient temperature rating: 122°F/50°C.

Autres manuels pour Mobile Link Unit

Table des matières

Autres manuels Generac Power Systems Instrument de mesure

Generac Power Systems

Generac Power Systems MINI DUST-FIGHTER Manuel utilisateur

Generac Power Systems

Generac Power Systems Mobile Link Unit Manuel utilisateur

Generac Power Systems

Generac Power Systems Mobile Link Unit Manuel utilisateur

Generac Power Systems

Generac Power Systems PCRGM1 Manuel utilisateur

Generac Power Systems

Generac Power Systems PWRview Instructions d'utilisation et de sécurité

Generac Power Systems

Generac Power Systems PM-DCP Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur