Gemini Tinyview TV-0020 Manuel utilisateur
Gemini Data LoggersGemini Data Loggers
Tinyview Logger Manual
The name ‘TINYVIEW’ covers a range of
miniature dataloggers fitted with LCD display,
capable of recording and displaying readings.
TINYVIEW offers many features including:
•14992 Reading capacity
•LCD display: 4 digits plus indicators
•Logging intervals of 1 second to 10 days
•Programmable delayed and trigger start
•Off-load whilst logging
•Min/Max/Actual readings
•Two programmable alarms
•3 Stop options
•Manufactured to BS EN ISO9002
•Complies with EN 50082 Pt1&2: 1992/95
TV-0020 TV-0050 TV-0073 TV-0076
TV-0104 TV-0204 TV-0304
9800-4346 Iss. 3 E&OE.
If this equipment is installed or used in a
manner not specified by the manufacturer then
the protection provided by the equipment may
be impaired.
This equipment contains a lithium battery
which must not be cut open, incinerated,
exposed to temperatures above 85°C (185°F)
or recharged. Dispose of in accordance with
local regulations.
The lithium battery should be replaced by a
trained technician using the battery supplied in
the appropriate manufacturer’s service pack.
This equipment should only be interfaced to a
UL or CSA listed computer.
WARNINGS
This equipment should only be interfaced to
equipment which is powered by a Safety Extra
Low Voltage Supply. The maximum voltage
levels are to be 30Vrms, 42V peak or 60V dc
and separated from hazardous voltages by
double or reinforced insulation. For the United
States consider a Safety Extra Low Voltage
Supply to be a Class 2 source as defined in the
National Electrical Code. It the unit is
connected to a computer outdoors the
computer must also comply.
This equipment is safe to use indoors or
outdoors over the temperature range –40°C to
85°C (-40°F to 185°F).
Contents
Features.................................................1
Managing software................…....…........4
Care of unit.........................…................5
IP Ratings……………………………………….…..5
Battery........................................…........6
Specification.........................…...............7
EMC Environment...............….……...........8
TINYVIEW Temperature....…….………….....8
TINYVIEW PT100 & PT1000.….…….……..10
TINYVIEW Rel. Humidity...………………....11
Calibration............................................13
Notes………………………………………………..14
Approvals.............................................15
Warranty..............................................16
FEATURES
Reading Capacity
TINYVIEW stores 14992 data readings, along
with related information such as the logging
interval and description/title, together with
details of the individual logger including the
unique serial number.
Delayed and Trigger Start
The logger may be programmed to delay the
start of the logging cycle by up to 45 days. The
delay can be set as relative or actual time and
will have full date/time retention. A clock face
symbol on the display indicates that the logger
is set for delayed start. Alternatively, it may be
set to start logging when a magnet is applied
to the case. This is indicated by arrows on the
screen pointing to where the magnet must be
applied.
Logging Intervals
The logging interval can be specified in either
seconds or minutes. The seconds mode can be
set up to 4.5 hours, the minutes mode up to 10
days. Certain features are only available in 1
minutes mode. An arrow on the display points
to a graph symbol when the unit is logging.
Off-load While Logging
When the logging interval is specified in
minutes it is possible to retrieve data from a
TINYVIEW without interrupting the logging
program.
Stop Options
TINYVIEW may be set to stop logging in one of
three ways:
i. Never (wraparound). In this mode
the logger continues to record, over-
writing the oldest data first once full.
ii. When full.
iii. After a specified number of readings.
Minimum, Maximum or Actual Readings
It is possible to record minimum, maximum or
actual readings. For minimum and maximum
readings, the recorded value is calculated from
readings taken during the logging interval.
Therefore a minimum logging interval of 2
minutes is needed for these functions.
2
Alarms
TINYVIEW has two programmable alarms. Both
use the LCD display to show an alarm state.
Both are fully programmable for:
i. Alarm trip point
ii. Over or under value.
iii. Latching or non-latching.
Alarm status is shown by the presence of Lo1,
Lo2, Hi1 and Hi2 indicators at the top of the
LCD. These can be cleared via the Windows
software without interrupting the logging.
Display
Numerical reading: Actual temperature or
Relative Humidity level. For temperature, an
arrow pointing to the bottom of the display
indicates the units used (degrees Centigrade or
Fahrenheit). The display is updated every 4
seconds.
Word ’STOP’: Logger in stop mode.
Display blank: In stop mode the logger
turns the display off after 5 minutes to
preserve battery life. When you connect to the
logger in GLM the display turns on again.
3
Word ‘CAL’: Indicates that the logger is
due or nearly due for calibration. This will only
appear on calibrated units and will not stop the
logger functioning. The word CAL will also
appear on calibrated units for a few seconds
each time the battery is inserted. Uncalibrated
units will display ‘BATT’ instead.
MANAGING SOFTWARE
Logging is started and the data retrieved by
means of the management software (GLM)
which is run on a Windows™ based host
computer. In order for TINYVIEW units to
communicate with the host computer, the
correct interface cable is required for
connection between a spare serial port on the
computer and your TINYVIEW data logger
(part number CAB-0007). Should any difficulty
be experienced in communicating with the unit,
firstly check that the cable is properly
connected to the correct serial port. Please
read the GLM manual before using your
TINYVIEW data logger.
4
Exporting Data
Data may be exported from the software in text
formats ready for importing into spreadsheet or
other programs. Exported data may include the
title, description and other headings.
CARE OF UNIT
General
Care must be taken to ensure that no dirt or
moisture gets into any connector. Moisture will
cause the unit to stop recording and can lead
to corrosion. Do not open the unit for any
purpose other than to change the battery,
particularly with RH units, as calibration may be
affected. Where the unit has been used in cold
conditions, allow it to warm to room
temperature prior to opening to avoid
condensation forming inside.
IP Ratings
TINYVIEW loggers are rated IP65 splashproof,
but only when connector caps are securely
fitted. In RH models, the sensor is necessarily
only protected to IP20.
5
Battery (Observe warnings inside cover)
Size: 3.6v ½ AA size Lithium
Life: Up to 1 year for PT100, 2 years for
other types.
Battery replacement is recommended at least
yearly for PT100 and every 2 years for the
other types. A Service kit including battery, O-
ring seal and silica gel pack is available from
your TINYVIEW distributor, Part No. SER-9550.
Always stop the unit logging before changing
the battery. To open the unit, unscrew the lid
from the base. Care should be taken when
handling the unit once the lid is removed, since
it may be damaged by static electricity.
Check that the replacement is aligned with
markings on battery holder. The word ‘batt’ will
appear on the display for a few seconds,
followed by the word ‘stop’. If it does not,
remove the battery and try again. When
replacing the battery, it is recommended that
the rubber seal and silica gel pack are also
replaced (see above). When refitting the lid
ensure that the electronics are seated properly
and that no wires are trapped.
6
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels Gemini Enregistreur de données
Gemini
Gemini Tinytag TE-4024 Manuel utilisateur
Gemini
Gemini Tinytag TE-4743 Manuel utilisateur
Gemini
Gemini Tinytag TGE-0001 Manuel utilisateur
Gemini
Gemini Tinytag Plus LAN Manuel utilisateur
Gemini
Gemini Tinytag TE-4101 Manuel utilisateur
Gemini
Gemini Tinytag Plus LAN Manuel utilisateur
Gemini
Gemini Berman Tinytag Plus TE-4201 Manuel utilisateur
Gemini
Gemini Tinytag Plus TE-4602 Manuel utilisateur
Gemini
Gemini TE-4022 Manuel utilisateur
Gemini
Gemini Tinytag TE-4703 Manuel utilisateur
Gemini
Gemini Tinytag TE-4600 Manuel utilisateur
Gemini
Gemini Tinytag TE-4021 Manuel utilisateur
Gemini
Gemini Tinytag TE-4904 Manuel utilisateur
Gemini
Gemini Tinytag TE-4804 Manuel utilisateur
Gemini
Gemini Berman Tinytag Plus TE-4021 Manuel utilisateur
Gemini
Gemini BERMAN Tinytag TE-4202 Manuel utilisateur
Gemini
Gemini Tinytag TE-4744 Manuel utilisateur
Gemini
Gemini Tinytag TE-4901 Manuel utilisateur
