Gefen HD-1000 Manuel utilisateur

HD-1000

Extender

Model # EXT-HD-1000

USER MANUAL

www.gefen.com

Technical Support:

Telephone (818) 772-9100

(800) 545-6900

Fax (818) 772-9120

Technical Support Hours:

8:00 AM to 5:00 PM Monday through Friday.

Write To:

Gefen Inc.

c/o Customer Service

20600 Nordhoff Street

Chatsworth, CA 91311

www.gefen.com

[email protected]

Notice

Gefen Inc. reserves the right to make changes in the hardware, packaging

and any accompanying documentation without prior written notice.

HD-1000 is a trademark of Gefen Inc.

HDMI is a trademark of HDMI.org

ASKING FOR ASSISTANCE

TABLE OF CONTENTS

Introduction / Operation Notes1.

Features2.

Sender Panel Descriptions3.

Receiver Panel Descriptions4.

Connecting and Operating the HD-10005.

Network Cable Wiring Diagram6.

Speciﬁcations7.

Warranty8.

The Gefen HD-1000 allows an HDMI video signal to be extended up to 330

feet (1640 w/o HDCP) using multi-mode LC-LC ﬁber optic cable. Fiber Optics

technology allows the HD-1000 to carry video signals over long distances that

are not possible with other technologies. Fiber Optic cables are immune to video

signal corruption from electromagnetic interference (EMI), ensuring a crystal

clear picture.

How It Works

The HD•1000S sender unit sits next to your set-top box or DVD player source.

Cables supplied with the HD•1000 connect your HDMI™ 1.3 source to the

sender unit. The display plugs into the back of the receiver unit. One CAT-5 cable

and a multi mode LC ﬁber optic cable connect the Sender and the Receiver units

to each other.

INTRODUCTION

READ THESE NOTES BEFORE INSTALLING OR

OPERATING THE HD-1000

50 or 62.5 micron multi-mode ﬁber optic cable is required for operation of the• HD-1000.

Maximum extension range of 330 feet (100 meters) when the source• requires HDCP. One CAT-5, CAT-5e or CAT6 cable is used to transmit DDC

and HDCP data back to the source.

Maximum range of 1640 feet (500 meters) when the source does not require• HDCP. This scenario does not require the CAT-5, CAT5e or CAT-6 cable if

the source does not require DDC information. If DDC is required, the use of

an EDID storage device (part# EXT-DVI-EDIDN, EXT-DVI-EDIDP) can be

used to transmit DDC information back to the source.

HDMI 1.3 compliant (please see FEATURES section on page 2 for• supported HDMI 1.3 features).

HDCP compliant•

Compatible with all HDMI and DVI* displays.•

NOTE: *When used with a DVI to HDMI adapter

OPERATION NOTES

FEATURES

Features

Extends high deﬁnition HDMI compliant devices up to 330 feet (100 meters)•

Uses a 4 strand multi mode LC-LC ﬁber optic cable for HDMI and a CAT5e cable for• DDC/control signals

Extends range of HDMI by equalizing signals•

HDCP and HDMI compliant with HDMI 1.3 Features•

Supports resolutions up to 1080p, 2K, and 1920 x 1200•

HDMI 1.3 Supported Features

12-bit/channel RGB Deep Color support•

CEC protocol support•

Lip-Sync pass-through•

Dolby TrueHD, DTS-HD pass-through•

xvYCC pass-through•

Includes:

(1) HD-1000S Sender unit

(1) HD-1000R Receiver unit

(2) 5V DC Power Supply

(1) 6 ft HDMI cable (M-M)

(1) User’s Manual

SENDER PANEL DESCRIPTIONS

Back Panel

Front Panel

Power LED

Indicator

RJ-45

Port

HDMI Input

Port

Fiber Optic

LC-LC Terminals

Status LED

Indicator

5V DC

Power Input

RECEIVER PANEL DESCRIPTIONS

Back Panel

Front Panel

Power LED

Indicator

RJ-45

Port HDMI Input

Port Fiber Optic

LC-LC Terminals

Status LED

Indicator

5V DC

Power Input

CONNECTING AND OPERATING THE HD-1000

How To Connect The HD-1000

Connect the HDMI source to the HD-1000 sender unit using the supplied HDMI1. cable.

Connect a user supplied CAT-5, CAT-5e or CAT-6 cable to the sender unit.2.

Connect four user supplied multi-mode LC terminated ﬁber optic cables into3. HD-1000 sender unit.

NOTE: 50 or 62.5 micron multi-mode ﬁber optic cable is required for operation of

the HD-1000.

Connect the other end of the CAT-5, CAT-5e or CAT-6 cable into the HD-4. 1000 receiver unit.

Connect the other ends of all four multi-mode LC terminated ﬁber optic5. cables into the HD-1000 receiver unit.

NOTE: Please take careful note of the labeling above each ﬁber optic port on

both the sending and receiving HD-1000 units. The most common user error is

to mis-match the ﬁber optic cable connections on each end, which results in no

video being transmitted.

Connect the display to the HD-1000 receiver unit using a user supplied6. HDMI cable.

Connect the included 5V DC power supplies into both the HD-1000 sending7. unit and receiving units.

Power on the display, followed by the source.8.

No further adjustments are necessary to operate the HD-1000.

NETWORK CABLE WIRING DIAGRAM

12345678

Gefen has speciﬁcally engineered their products to work with the TIA/EIA-568-B

speciﬁcation. Please adhere to the table below when ﬁeld terminating cable for

use with Gefen products. Failure to do so may produce unexpected results and

reduced performance.

CAT-5, CAT-5e, and CAT-6 cabling comes in stranded and solid core types.

Gefen recommends using solid core cabling. CAT-6 cable is also recommended

for best results.

Each cable run must be one continuous run from one end to the other. No splices

or use of punch down blocks.

Pin Color

1 Orange / White

2 Orange

3 Green / White

4 Blue

5 Blue / White

6 Green

7 Brown / White

8 Brown

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Gefen Extenseur

Gefen

Gefen EXT-DVI-FM2000 Manuel utilisateur

Gefen

Gefen ex-tend-it CAT5-1000 Manuel utilisateur

Gefen

Gefen EXT-COMPAUD-CAT5-142 Manuel utilisateur

Gefen

Gefen ext-hdmi-cat5x Manuel utilisateur

Gefen

Gefen ToolBox GTB-USB2.0-4LR Manuel utilisateur

Gefen

Gefen USB-400FO Manuel utilisateur

Gefen

Gefen GTB-3DTV-KVM Manuel utilisateur

Gefen

Gefen GTV-WHDMI Manuel utilisateur

Gefen

Gefen VGA-141SR Manuel utilisateur

Gefen

Gefen ETH-2-PLC Manuel utilisateur

Gefen

Gefen EXT-CAT5-1600A Manuel utilisateur

Gefen

Gefen DVI-3000HDS Manuel utilisateur

Gefen

Gefen EXT-DVIKVM-LAN-L Manuel utilisateur

Gefen

Gefen EXT-2DVI-CAT6DL Manuel utilisateur

Gefen

Gefen EXT-DP-CP-FM10 Manuel utilisateur

Gefen

Gefen COMP-141N Manuel utilisateur

Gefen

Gefen EXT-CAT5-9500HD Manuel utilisateur

Gefen

Gefen GTV-WHDMI Manuel utilisateur

Gefen

Gefen ex-tend-it DVI-CAT5 Manuel utilisateur

Gefen

Gefen HDMI 1000HD Manuel utilisateur

Gefen

Gefen EXT-DVI-141SBP Manuel utilisateur

Gefen

Gefen DVI CAT-5 Extreme Manuel utilisateur

Gefen

Gefen DVI-CAT5-4X Manuel utilisateur

Gefen

Gefen EXT-HDMI1.3IR-FO-141 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur