GE Concord 4 Manuel utilisateur
GE Concord 4 Quick Setup Guide
For more detailed information, please see the GE Installation Manual.
1. Planning your system
a. Wired Zones: A hardwired zone can consist of 1 or more sensors in a loop.
Each zone loop must consist of similar sensors, that can be programmed the
same.
i. Normally Open Sensors ormally open sensors have an “Open”
circuit until the sensor is tripped, it will then close the circuit. This
change is detected by the panel, and causes the alarm. These sensors
get wired in Parallel. (See Wiring Diagrams)
ii. Normally Closed Sensors ormally closed sensors have a “Closed”
circuit until the sensor is tripped, it will then open the circuit. This
change is detected by the panel, and causes the alarm. These sensors
get wired in Series. (See Wiring Diagrams)
iii. Powered Sensors Powered Sensors, such as Motion detectors, Glass
Break Detectors will require a 4 conductor wire. Two wires are for
power connections, and two wires
are for the zone connections.
b. Wireless Zones Unlike wired zones, for
each wireless sensor you will use 1
wireless zone. Each sensor is programmed
to a zone with all information for that
individual sensor.
2. Wiring the System
a. Keypads All Keypads get wired to Pins 3,
4, 5, and 6. the system will automatically
detect the number of keypads connected
to the system. Match the colors used on
each pin, to the corresponding connections
on the keypad. (See Diagram to Right)
b. Sensors
i. Normally Open Sensors Check
the product documentation – If the
Loop Type is “ O” or “ ormally
Open” then the sensors should be
wired in Parallel with the zone.
(See Diagram On Last Page)
ii. Normally Closed Sensors Check
the Product Documentation – If the
Loop Type is “ C” or “ ormally
Closed” then the sensors are wired in Series with the zone (See
Diagram to On Last Page)
3. Programming The System
a. Entering Programming Mode
1. Make sure the system is disarmed in all partitions.
2. Press 8 + 4321 + 0 + 0. The display shows “SYSTEM PROGRAMMING”.
b. Programming Hardwired Zones
i. Zone Groups are pre-programmed for the 8 hardwired zones.
1. Entry Exit Delay – For Doors that require a delay for entry or
exit
2. Instant Interior Follower – For motion detectors that will
arm instantly.
3. Instant Perimeter – For all doors/window sensors, glass
break detectors that do not require a delay.
ii. **Change the “Pre-Programmed” Zone Settings
1. Once you are in the programming mode, press B until the
display shows “Sensors”, and press # to select
2. ow Press B until the display shows “Edit”, and press # to
select.
3. Press A or B to scroll to the zone number you desire to change
press # to select
4. Enter the desired partition number, and then press #. (Most Applications the
Partition is always 1) The display shows the new partition assignment.
5. Press A or B and the display shows SENSOR GROUP nn (current group
assignment)
6. Enter the desired group number, (See appendix B in Installation Manual) then
press #. The display shows the new group assignment.
c. Programming Wireless Zones
i. With the display showing SENSORS, press # and the display shows “Learn Sensors”
ii. Press # and the display shows Sensor PTN 1
iii. Press # to select partition 1 or press 2, 3, 4, 5, or 6 + # to select the desired partition
(Typically is always Partition 1). The display should show “Sensor Group 0”
iv. Enter the desired sensor group number and press # to select (see Table B1 in “Appendix
B” for a description of all sensor group characteristics). The display shows TRIP
SENSOR nn, where nn is the displayed (next available) sensor number.
v. To change the displayed sensor number, enter the desired sensor number + #. The desired
sensor number is displayed.
vi. With the desired sensor number displayed, use the guidelines in Table 6 to force the
sensor or zone you are adding (learning) into the panel memory to send a signal to the
panel.
vii. To add another sensor to the same sensor group and partition, go back to step 5.
viii. To add sensors to another sensor group or partition, press * twice and go back to step 1
(LEARN SENSORS).
d. Changing Wireless Zone Settings:
i. If you need to change a zone setting – Enter Programming Mode, Press B to Scroll the
menu. Select “Sensors” # “Edit” # Select the Zone you wish to Edit, and make the desired
changes pressing # to save the desired changes.
e. Exiting Programming Mode
i. After all installer/dealer programming is completed, use the following procedure to exit
programming mode.
To exit programming mode:
1. Press * until the display shows SYSTEM PROGRAMMING.
2. Press A or B until the display shows EXIT PROGRAMMING READY.
3. Press # and the touchpad displays the TIME AND DATE.
f. Using The System
i. Setup User Codes:
1. To Enter User-Programming Mode
a. Press 9 then the 4 digit Master Code (Default is 1234)
2. Scroll Menu using the B Button until you reach “User”
3. With the display showing USER CODES, press # and the display shows REGULAR
USER CODES.
4. Press # and the display shows USER nnn (first available user number).
5. Press A or B to select the desired user number, and then press #. The display
shows USER nnn - nnnn.
6. With the desired user number displayed, enter a 4-digit user code. The display
flashes the entered code. Press # and the display shows USER nnn - nnnn (new
code).
Zone Wiring Diagrams
Autres manuels pour Concord 4
3
Table des matières
Autres manuels GE Système de sécurité
GE
GE CareGard Manuel utilisateur
GE
GE SuperBus 2000 Manuel utilisateur
GE
GE NetworX Manuel utilisateur
GE
GE NX-108E - Security NetworX NX-4 System Manuel utilisateur
GE
GE 60-362 Manuel utilisateur
GE
GE Concord express Mode d’emploi
GE
GE NX-10 Guide de l'utilisateur
GE
GE NetworX V3 Manuel utilisateur
GE
GE NX-10 Manuel utilisateur
GE
GE 45133 Manuel utilisateur
GE
GE 45413 Manuel utilisateur
GE
GE Concord Manuel utilisateur
GE
GE 4 Series Manuel utilisateur
GE
GE 45129 Manuel utilisateur
GE
GE SmartHome Series Manuel utilisateur
GE
GE Concord 4 Manuel utilisateur
GE
GE Silent Alert 45137 Manuel utilisateur
GE
GE Security Pro 7000 Manuel utilisateur
GE
GE Allegro 60-874-95R Manuel utilisateur
GE
GE 45232 Manuel utilisateur
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur