GE MapSight Manuel utilisateur
GE MapSight™ Tech Tip
MS-206-15-08-1.0
Step 1 - GE MapSight Approved Screen Protector
It is important to protect the touch screen of your GE MapSight device with a screen protector. The constant use of a
stylus, particularly in high use areas such as the “OK button”, can cause damage or scratching of the screen which can be
prevented with a screen protector.
To avoid damage, only use the stylus that came with the GE MapSight device and a screen protector that fully covers the
screen. Replacement of the MapSight screen protector is required maintenance every three months or sooner, if receiving
excessive use.
To ensure the screen protector ts the device screen, we ask that users order the covers directly from ikeGPS or purchase
the JAVOedge brand in the appropriate size. To place orders with ikeGPS, please contact your sales representative, or send a
Instructions for applying a screen protector to your MapSight device are noted below:
Before opening, make sure the screen protector package is in
good condition. It should not be bent or scratched.
Each package will include:
• Plastic Screen Protector
• Cleaning Cloth
• Installation card (to smooth out bubbles)
For best results, wash hands before installing and apply in a
dust-free environment.
Do not use any cleaning solution on the screen.
1Copyright © 2015 ikeGPS
How to Apply a Screen Protector
to GE MapSight Device
MS-206-15-08-1.0 2Copyright © 2015 ikeGPS
Clean the MapSight device screen with the dust free cloth
provided and remove any ngerprints, dirt, and smudges.
Step 2 - Cleaning the MapSight Screen
After wiping the screen, use an air-blower (as seen in the
photo) or an air compressor to clear away any excess dust.
away dust. Simply turn the device upside down to blow o
the dust.
NOTE: It is very important to remove all dust and ngerprints
from the GE MapSight screen before applying the screen
protector
Step 3 - Step 3 - Removing Dust
MS-206-15-08-1.0 2Copyright © 2015 ikeGPS
Step 5 - Prepping the First Film Protector
When the device screen is clean and prepped, begin to slowly
peel a small portion of the protective lm using the tab noted
as #1. This will expose the tacky back-side of the screen
protector approximately one inch.
NOTE: Do not touch the exposed tacky side of the screen
protector.
Step 4 - Two Protective Films
Screen protectors are shipped with a front and back protective
lm. They are identied with a yellow tab as #1 and #2.
Step 7 - Removing Second Protective Film
MS-206-15-08-1.0 2Copyright © 2015 ikeGPS
Once the screen protector has been applied, remove
the second protective lm using the yellow tab #2.
Step 6 - Applying Screen Protector
Place the tacky side against the MapSight LCD Screen and
carefully align the screen protector to match the bottom or
top edge of the display. Take care in this step to ensure the
screen protector is well aligned so that it will t the whole
screen.
As you slowly pull o the protective lm using Tab #1, lightly
press the tacky side down so it will adhere to the LCD screen.
MS-206-15-08-1.0 3Copyright © 2015 ikeGPS
For more information, contact us at support@gemapsight.com, or visit our support at our website www.gemapsight.com
+1 720 381 1634 (direct dial)
+1 844 445 3477 ext 3 (toll free)
Hours: Mon-Fri 8am-5pm MST
Step 8 - Removing Air Bubbles
Use Plastic Installation Card (included in your package) to push
any trapped air bubbles to the edge of the screen. Start at the
center and work towards the outer edge.
Do NOT use sharp tools to remove the screen protector as this
may damage the screen.
Autres manuels pour MapSight
1
Table des matières
Autres manuels GE Enregistreur de données
