GE ZKHCSS2 Manuel utilisateur

Installation

Instructions ZKHCSS2

Tubular Stainless Steel Handles

and Handle Side Trim

Right hand door swing models are illustrated in these

instructions. Follow these same instructions for left hand

models.

This kit provides for the installation of Tubular Stainless

Steel handles or custom handles on 3/4" overlay custom

panels.

Tools and materials required:

• #2 Phillips screwdriver

• Drill and 7/32", 1/8" bits and 7/8" spade bit

• Custom door panels,

• Safety glasses

• Center punch

• Hammer

• Pencil

Parts List:

A. Freezer tubular handle (95376) and

fresh food tubular handle (95377)

B. 4 Handle standoffs, 70536

C. 6 Screws for handle standoffs

#10-32x1" pan head machine screws (4 required, 2 extra), 36298

D. 6 Set screws (4 required, 2 extra) 70539

E. 3/32” Allen wrench for set screws, 70548

F. 6 Plastic spacers (4 required, 2 extra) 70540

G. 5 Trim screws (4 required, one extra) 8665

H. Handle side trim for LH models (75468), trim for RH models (75469)

Before you begin – Read these instructions completely and carefully.

Note to Installer: Be sure to leave these instructions with the Consumer.

Note to Consumer: Keep these instructions with your Owner’s Manual for future reference.

STEP 1 REMOVE DOOR AND

DRAWER HANDLES

• Open refrigerator door to 90°. Remove the 4 screws

holding the handle to the door.

• Remove 4 screws holding handle side trim. Discard all

screws and trim. Discard handle.

• Open freezer drawer to access handle and trim.

Remove and discard handle, retain screws and trim.

If you are installing custom handles, go to STEP 3.

STEP 2 INSTALL TUBULAR STAINLESS STEEL HANDLES ONTO PANELS

-2-

CAUTION: Hole locations must be exact to accept handle standoff

and handle assembly.

Assemble Handles

• Place a handle standoff on each attachment post on

the handle. Position the screw hole on the standoff to

point to the floor.

• Install set screws into the bottom of each standoff,

using the Allen wrench provided. The standoff should

be tight against the handle.

Screw

Allen Wrench

Attachment Post

Secure Handles to Panels

• Use a 7/8" spade bit to drill 1/2" to 9/16" max.

depth into the back side of the panel. At this depth

there will be enough screw threads to engage the

handle on the appearance side. See illustration.

• Stand the panel up on the hinge side. Place a plastic

spacer into the 7/8" opening, drop screw through

the spacer.

Countersink screw

into panel as shown.

• Place handle standoffs against the mounting screws on

the appearance side, drive top screw partially into the

standoff.

• Drive next screw partially into the standoff. Continue

installing screws to the bottom location. Alternate

back to the top tightening screws one at a time until

the handle is tight against the panel.

7/8"

1/2" Min.

9/16" Max.

1.100"

3/4"

7/32"

Plastic

Spacer

Fresh Food Panel

Freezer Drawer

Panel

Drill

Pilot

Holes

Match

Handle

1-1/8"

Drill Pilot Holes

• Measure, mark and draw a line, 1-1/8" from the handle

side edge, top to bottom.

• Hold the tubular handle against the appearance side,

centered top to bottom and on the marked line.

• Mark the screw hole locations at the center of the

handle attachment posts. Place handle over the marks

to check again that holes are aligned to handle posts.

• Center punch to mark hole locations. Drill 7/32" pilot

holes from the appearance side and through the entire

panel thickness.

• Follow the same procedure to drill pilot holes on the

freezer door.

-3-

STEP 3 INSTALL ASSEMBLED PANELS

Install

8 Screws

Install 4

Handle Side

Trim Screws

• Install custom handles according to the manufacturer’s

instructions.

• Slide assembled door panel into

the trim.

• Determine the correct trim for

your model (for left or right

door swing). Place trim against

the side of the refrigerator door,

aligned top to bottom. The holes

in the trim should align to the

holes in the door. Discard the

other trim piece.

• Remove trim. Use a 1/8" bit to drill the semi-punched

holes in the refrigerator door.

• Secure the new custom handle side trim using the

supplied screws.

• Slide assembled panel into the drawer trim.

• Secure the original drawer trim using original round

head trim screws.

Refrigerator

Door

Custom Trim

Trim to Panel Fit

Pub. No. 31-46033-2

Dwg. No. 197D4869P001

(N.D. 532) 9/02

75470

Note: While performing installations described in this book,

safety glasses or goggles should be worn.

For Monogram®local service in your area, call

1-800-444-1845.

Note: Product improvement is a continuing endeavor at

General Electric. Therefore, materials, appearance and

specifications are subject to change without notice.

General Electric Company

Louisville, KY 40225

Monogram.

We bring good things to life.

Autres manuels GE Accessoires

GE Brand Expression Guidelines Manuel utilisateur

GE MIFII GEK-106237P Manuel utilisateur

GE WIR-10-SR-G-D-W Manuel utilisateur

GE 19298 Manuel utilisateur

GE PrecisionLine RCR-90 Manuel utilisateur

GE WR72X10313 Guide de configuration

GE 868 GEN2 Guide de démarrage rapide

GE DDI602 Instructions de montage

GE Monogram ZBD7005GII Manuel utilisateur

GE PRV02 Instructions originales

GE RSEN-LG Manuel de service

GE TX-1211-03-1 Manuel utilisateur

GE IMRSEN-W12 Manuel utilisateur

GE Monogram ZXR7510 Manuel utilisateur

GE CPLGSTDBLW1 Manuel utilisateur

GE WARRANTY CARD Mode d’emploi

GE ve735am Manuel utilisateur

GE Aritech PB501 Manuel utilisateur

GE 19234 Manuel utilisateur

GE 319.5 Manuel utilisateur

GE PDW7800N00CC Manuel utilisateur

GE Telaire Vaporstat 9002 Manuel utilisateur

GE Telaire Ventostat 8001 Manuel utilisateur

GE 40795 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur