GE Interlogix CyberScout Interlogix Manuel utilisateur
CyberScout
Compact Pan/Tilt Cameras
© 2002 Kalatel, a GE Interlogix company
All Rights Reserved.
Any GE Interlogix, Kalatel division, software
supplied with GE Interlogix, Kalatel division,
products is proprietary and furnished under
license and can be used or copied only in
accordance with the terms of such license.
This document contains proprietary
information that is protected by copyright. No
part of this document may be reproduced or
transmitted in any form or by any means
without the prior written permission of GE
Interlogix, Kalatel division.
The information contained in this document is
subject to change without notice.
GE Interlogix, Kalatel division, in keeping pace
with technological advances, is a company of
product innovation. Therefore, it is difficult to
ensure that all information provided is entirely
accurate and up-to-date. GE Interlogix, Kalatel
division, accepts no responsibility for
inaccuracies or omissions and specifically
disclaims any liabilities, losses, or risks,
personal or otherwise, incurred as a
consequence, directly or indirectly, of the use
or application of any of the contents of this
document.
For the latest product specifications, visit
GE Interlogix, Kalatel division, online at
www.kalatel.com or contact your Kalatel sales
representative.
For technical support before and after installation, call 800-469-1676.
Technical support is available 24 hours a day, 7 days a week.
Call: Tech Support 800-469-1676 (6 A.M. – 5 P.M. PST Monday through Friday)
Tech Support 541-740-3589 (all other times)
Main 800-343-3358 or 541-754-9133
Fax: Tech Support 541-752-9096 (available 24 hours a day)
Main 541-754-7162
Web: www.kalatel.com
1038864A / December 2002
This equipment has been tested and
found to comply with the limits for a
Class A digital device, pursuant to part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
when the equipment is operated in a
commercial environment. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instruction manual, may cause
harmful interference to radio
communications.
You are cautioned that any changes or
modifications not expressly approved
by the party responsible for compliance
could void the user's authority to
operate the equipment.
CyberScout User Manual Table of Contents
1038864A / December 2002 3
TABLE OF CONTENTS
BEFORE YOU BEGIN................................................................5
1INTRODUCTION ..................................................................6
1.1 PRODUCT DESCRIPTION..............................................6
1.2 OPERATION REQUIREMENTS........................................6
1.3 CABLE REQUIREMENTS ...............................................7
1.4 POWER REQUIREMENTS..............................................7
1.5 POWER CABLE SIZE AND LENGTH .................................7
2INSTALLING THE CYBERSCOUT...........................................8
2.1 UNPACKING THE CYBERSCOUT ....................................9
2.2 INSTALLING THE MOUNT............................................11
2.2.1 Flush-Mount Adapter ..................................................11
2.2.2 Wall-Mount Adapter....................................................15
2.2.3 Surface-Mount Adapter ..............................................17
2.3 MAKING CABLE CONNECTIONS ...................................19
2.4 SETTING THE DATA TERMINATION SWITCH...................20
2.5 INSTALLING THE PAN/TILT ASSEMBLY .........................21
2.5.1 Flush-Mount Adapter ..................................................21
2.5.2 Wall-Mount Adapter....................................................22
2.5.3 Surface-Mount Adapter ..............................................23
2.6 APPLYING POWER TO THE CAMERA ............................24
2.7 SETTING THE SITE ADDRESS DIP SWITCH ....................25
2.8 CONNECTING THE TEMPORARY VIDEO OUTPUT............27
2.9 ADJUSTING THE CAMERA...........................................28
2.9.1 Adjusting the Varifocal Lens.......................................28
2.9.2 Adjusting the 4 mm Fixed-focal Lens .........................29
2.10 ATTACHING THE DOME ..............................................30
Table of Contents CyberScout User Manual
4 1038864A / December 2002
3OPERATING THE CYBERSCOUT ........................................31
3.1 KEYPAD OPERATION ................................................31
3.1.1 Programming CyberScout Macros into the KTD-404
Keypad .......................................................................31
3.2 STANDALONE OPERATION ........................................36
4TROUBLESHOOTING.........................................................39
WARRANTY AND RETURN INFORMATION..................................41
ADVANCE REPLACEMENT POLICY .....................................41
CyberScout User Manual Before You Begin
1038864A / December 2002 5
BEFORE YOU BEGIN
Read these instructions before installing or operating this product.
Note: This installation should be made by a qualified service person and should conform to
local codes.
This manual provides installation and operation information. To use this
document, you must have the following minimum qualifications:
• A basic knowledge of CCTV systems and components
• A basic knowledge of electrical wiring and low-voltage electrical
hookups
Use this product only for the purpose for which it was designed.
Customer Support
For assistance in installing, operating, maintaining, and troubleshooting
this product, refer to this document and any other documentation
provided. If you still have questions, contact Kalatel Technical Support:
GE Interlogix, Kalatel division
Call: 800-469-1676
Fax: 541-752-9096
Note: You should be at the equipment, ready with details before calling Technical Support.
Conventions Used in this Manual
Boldface or button icons highlight command entries. The following
WARNING, CAUTION, and Note statements identify potential hazards:
* WARNING:
Improper use of this equipment can cause severe bodily injury or
equipment damage.
** CAUTION:
Improper use of this equipment can cause equipment damage.
Note: Notes contain important information about a product or procedure.
* This symbol indicates electrical warnings and cautions.
** This symbol indicates general warnings and cautions.
Introduction CyberScout User Manual
6 1038864A / December 2002
1 INTRODUCTION
This manual provides step-by-step installation instructions for all
CyberScout cameras and accessories.
1.1 PRODUCT DESCRIPTION
CyberScout™ is a line of compact, variable speed, pan/tilt cameras used
for discreet surveillance. A CyberScout’s operational features are
customized and stored within its on-board programmable nonvolatile
memory. You can program and operate your CyberScouts with your
Kalatel keypad.
Note: Not all CyberScout features are accessible from all keypads. Refer to your keypad’s
programming manual and section 3.1 Keypad Operation in this manual.
CyberScouts come in a variety of camera and dome options. Please
refer to the product brochure, specification, and catalog for details.
1.2 OPERATION REQUIREMENTS
CyberScouts can be operated with or without a keypad. CyberScouts
contain a built-in receiver that decodes commands originating from a
keypad. From the keypad, an operator can pan a CyberScout 360°
(noncontinuous), tilt it 90°, control its digital zoom, set and find preset
positions, set and initiate autopan movements, and set and initiate a
ShadowTour™.
No keypad is required when operating a CyberScout as a standalone
fixed autopan camera. See section 3.2 Standalone Operation.
Figure 1. Typical operation application with one keypad
CyberScout User Manual Introduction
1038864A / December 2002 7
1.3 CABLE REQUIREMENTS
Cable Requirement
Video Coaxial (75 ohm)
Power 24 VAC unshielded twisted-pair
Note: See Table 1 to determine the gauge and length.
Control RS422 unshielded twisted-pair cable
Note: The recommended cable size is 22 gauge (0.64 mm).
1.4 POWER REQUIREMENTS
CyberScouts require a 24 VAC power supply to operate the pan/tilt drive,
camera, and blower. At 24 VAC, the CyberScout requires 6 VA of power.
Note: CyberScouts do not require isolated power inputs.
1.5 POWER CABLE SIZE AND LENGTH
CAUTION:
Choose the proper gauge of the cable to supply 24 volts to the
CyberScout. An inadequate gauge will cause a voltage drop
resulting in improper operation.
Table 1 provides the recommended cable lengths of varying wire gauges.
Table 1. Recommended maximum cable lengths
Maximum Cable Length
Wire Gauge CyberScout
(6 VA)
(awg) (mm2) Feet Meters
10 2.60 7500 2288
12 2.05 4750 1450
14 1.62 3000 913
16 1.29 1875 575
18 1.02 1163 355
20 0.81 725 225
22 0.64 463 140
Installing the CyberScout CyberScout User Manual
8 1038864A / December 2002
2 INSTALLING THE CYBERSCOUT
Wall-mount mounting
adapter
Housing and pan/tilt
assembly
Camera shroud
A complete CyberScout consists
of a mounting adapter, a housing
and pan/tilt assembly (with a built-
in receiver, camera, and a camera
shroud), and a polycarbonate
dome. See Figure 2.
Dome
Figure 2. A complete CyberScout
The method of installation depends on which mounting adapter is being
used. Installation involves securing the mounting adapter, making the
cable connections, attaching the CyberScout, setting the address DIP,
adjusting the camera, and fastening the polycarbonate dome.
CAUTION:
For safety, the hardware and procedure used for securing the
CyberScout must be able to support at least 35 pounds (15.88 kg).
CyberScout User Manual Installing the CyberScout
1038864A / December 2002 9
2.1 UNPACKING THE CYBERSCOUT
1) Remove the contents from the box.
Box* 8-32 x 1 3/4 machine screws for wall-
mount or flush-mount adapters
CyberScout assembly Video interconnect cables (two)
Wall-mount adapter RJ45 interconnect cable
Optional torque-head, tamper-resistant
captive screws for dome ring
Interface module
8-18 Type B self-tapping screws for
surface-mount or conduit adapters
*Includes all mounting adapters, one dome assembly, and internal components. Does not
include the fasteners or secondary brackets needed to attach the CyberScout to a surface.
Figure 3. Unpacking the product package
Installing the CyberScout CyberScout User Manual
10 1038864A / December 2002
2) Separate the mounting adapters and dome from the pan/tilt
assembly. See Figure 4.
Loosen, but do not remove, the
captive screws.
Separate the dome from the
pan/tilt assembly.
Separate the surface-mount
adapter from the pan/tilt assembly.
Separate the flush-mount adapter
from the pan/tilt assembly.
Figure 4. Separating the CyberScout assembly components
3) Set the parts aside in a safe, accessible location where the dome
will not get scratched.
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels GE Interlogix Caméra de sécurité
