GAVI Folding Workbench Manuel utilisateur

GAVI FOLDING WORKBENCH INSTALLATION INSTRUCTIONS

For questions, contact Sue at (847) 387-6704 or [email protected].

Visit gavipop.com/foldingworkbench for installation videos and additional information.

Revised 3/22/16

The GAVI Folding Workbench is shipped in 2 BOXES (1 box containing the tabletop

and 1 box containing the metal parts). Note that the metal brackets are preassembled

in the middle table height position (approximate 36” table height). The table height can

be adjusted after installation. Table height adjustment instructions are on page 3.

Tools required for installation: #2 Square Drive Bit (included),

5/32” Allen Wrench (included), Phillips Head Screwdriver.

Step 1: On the wall where the workbench will be mounted, using a stud nder, nd the center of the stud for mounting

the left bracket. Place a reference mark at the center of the stud 68” from the oor. (See g. A)

Before you begin, decide where you are going to install the tabletop, making

sure you have at least a minimum of 52” of unobstructed wall space.

Disclaimer: The screws provided with the GAVI Folding Workbench are for wood stud installations only. Other applications

may require different screws for proper and safe use. It is the buyer’s responsibility to research, secure and use the right

screws for applications other than wood studs.

LEFT BRACKET INSTALLATION

68”

Step 2: Attach the left bracket through the 1st hole at the top, using the supplied

screw. (Black #8 x 2” long - Part# 21347-19) Do not tighten the screw all of the

way at this time. (See g. B)

Step 3: Use a level so the bracket is vertically straight. Make sure to place the

level against the at part of the bracket and not against any screw heads along

the side.

Step 4: Without moving the level, mark the center of the last hole at the bottom of

the bracket. Attach with a screw and tighten all of the way. Then, go back to the

top screw and nish tightening it all of the way.

Install rst

screw in rst

hole

Bracket Leg

Wall

Floor

Center of Stud

Wood Stud

Install second

screw in

bottom hole

GAVI FOLDING WORKBENCH INSTALLATION INSTRUCTIONS

For questions, contact Sue at (847) 387-6704 or [email protected].

Visit gavipop.com/foldingworkbench for installation videos and additional information.

Step 5: Unfold the bracket to attach three (3) more screws.

(See g. C) Tighten screws all of the way to properly secure

the bracket to the wall.

Step 6: Locate the center of the stud for mounting the right

bracket. It should be at least 24” away from the left bracket.

Step 7: Position the level on top of the left bracket extending

past the stud (for the right bracket), and make a reference

mark across the stud. (See g. C)

Step 8: Position the top of the right bracket even with the

reference line. Then repeat steps 2-5 to mount the right

bracket.

Step 9: Re-insert Safety Pins in the 7th hole from the bottom

in each bracket. (See g. D)

Step 10: Position the tabletop on the brackets so it is equally

spaced left and right, and 1¾” from the wall.

Step 11: Using the supplied screws, attach the tabletop to

the brackets. (Silver #10 x 3/4” long Part# 21347-5) 6 screws

total - (See g. E)

With the butcherblock tabletop, it’s recommended to pre-drill

1/8” holes ¾” deep.

The GAVI Folding Workbench is now ready to be used.

Tabletop

Safty Pins Safty Pins

Unfolded

Bracket

(3) Screws

for each bracket

Left Bracket

Right Bracket

Safety Pin

Reference

Mark

Level

D E

(3) screws

For questions, contact Sue at (847) 387-6704 or [email protected].

Visit gavipop.com/foldingworkbench for installation videos and additional information.

To store the tabletop in the

stored position, remove

the Safety Pins and slide

the tabletop all the way

up. Then re-insert the

safety pins.

42” Table Height:

1) To adjust the table height to 42”, start from the stored postion with the safety pins in place.

(See g.A1) Using the supplied allen wrench, unscrew and remove the bottom bolt, spacer,

and nut (do the same on the right side). (See g.A2 - exploded view)

2) Swing the tabletop out and reposition the bracket legs to the next higher holes. (See g.A3)

3) Put the bolt, spacer, and nut back in the hole and repeat on the other side.

4) Remove the Stop and reinstall on the 8th hole from the bottom (both left and right).

5) Slide tabletop down and replace Safety Pin in 4th hole from top. (See g.A4)

30” Table Height:

1) To adjust the table height to 30”, start from the stored postion. Remove Safety Pins and slide

tabletop down enough to re-insert the Safety Pins into the 3rd hole from the top. (See g.

B1) With the Safety Pins in place, use the supplied allen wrench, to unscrew and remove the

bottom bolt, spacer, and nut (do the same on the right side). (See g.B2 - exploded view)

2) Reposition the ends of the bracket legs to the bottom holes. (See g.B3)

3) Put the bolt, spacer, and nut back in the hole and repeat on the other side.

4) Remove the Stop and reinstall on the 4th hole from the bottom (both left and right).

5) Slide tabletop down and replace Safety Pin in 5th hole from bottom. (See g.B4)

GAVI FOLDING WORKBENCH INSTALLATION INSTRUCTIONS

TABLE HEIGHT ADJUSTMENT INSTRUCTIONS

Safety

Bolt,

Spacer,

and Nut.

Bracket Leg

Stop

Bracket Diagram

Storing Workbench

g.A2 - exploded view

g.B2 - exploded view

Bolt

Bracket Bracket Leg

Spacer

Nut

Bolt

Bracket Bracket Leg

Spacer

Nut

g.A3

g.B3

g.A4

g.B4

g.A1

g.B1













































    

    

   

   

   

    

   

   

   

    

    

    

    

    

    

    

    

    

    

   

 

     

































 







 

































 



















































    

    

   

   

   

    

   

   

   

    

    

    

    

    

   

 

     

































 







 































 







PARTS LIST

HARDWARE BAG CONTAINS:

Part #5 - 3/4” silver screws

Part #19 - 2” black screws

Part #20 - #2 Square Drive Bit

Part #21 - 5/32” Allen Wrench

Disclaimer: The screws provided with the GAVI Folding Workbench are for wood stud installations only. Other applications

may require different screws for proper and safe use. It is the buyer’s responsibility to research, secure and use the right

screws for applications other than wood studs.





















  



 















     

































 







 









   

   

   

   







For questions, contact Sue at (847) 387-6704 or [email protected].

Visit gavipop.com/foldingworkbench for installation videos and additional information. 4

GAVI FOLDING WORKBENCH INSTALLATION INSTRUCTIONS

20 21347-20 #2 SQUARE DRIVE BIT 1

21 21347-21 5/32” ALLEN WRENCH 1

Manuels Rangement des outils populaires d'autres marques

Ryobi

Ryobi RWB03 Manuel utilisateur

Husky

Husky H27CH5TR4BGK Manuel utilisateur

Scheppach

Scheppach ts 2100 Manuel utilisateur

Cornwell Tools

Cornwell Tools CTB360AKBK Manuel utilisateur

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Manuel utilisateur

Cassese

Cassese CS200 CART Manuel utilisateur

Kendall Howard

Kendall Howard ESDW-9630-1000 Manuel utilisateur

Lista

Lista Align Instructions de montage

Workzone

Workzone 99609 Manuel utilisateur

Stanley

Stanley STST83800-1 Manuel utilisateur

Homak

Homak PROFESSIONAL Series Manuel du système

Perel

Perel ROLLER SHUTTER STORAGE CABINET Manuel utilisateur

Husky

Husky H5CH2R Manuel utilisateur

BGS technic

BGS technic 4107 Manuel utilisateur

Clarke

Clarke CWB1250 Manuel utilisateur

Ryobi

Ryobi RWB02 Manuel utilisateur

Husky

Husky H52CH6HDV3WHT Manuel utilisateur

Sealey

Sealey PTB66004 Manuel utilisateur