Gastops ChipCHECK CC120 Mode d'emploi
CC120 Health and Safety
CHIPS ANALYZER (B166500)
CAUTION –USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE
THE INFORMATION, TECHNICAL DATA AND DESIGNS DISCLOSED HEREIN ARE THE EXCLUSIVE PROPERTY OF GASTOPS LTD. AND ARE NOT TO BE
USED OR DISCLOSED TO ANY OTHERS WITHOUT THE WRITTEN CONSENT OF Gastops LTD. ANY RECIPIENT, BY ITS RETENTION AND USE, AGREES
TO HOLD IN CONFIDENCE ANY INFORMATION, TECHNICAL DATA AND DESIGNS DISCLOSED HEREIN. THE FOREGOING SHALL NOT APPLY TO
PERSONS HAVING PROPRIETARY RIGHTS TO SUCH INFORMATION, TECHNICAL DATA OR DESIGNS TO THE EXTENT THAT SUCH RIGHTS EXIST.
Gastops Ltd.
C009423, Rev. 4 page 4
All use of this publication and ChipCHECK by user shall be subject to the restrictions and conditions as set out in this publication.
2.0 Health and Safety
2.1 Operational Safety
CAUTION – USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION – PRIOR TO ANY USE, THE EQUIPMENT MUST BE INSPECTED FOR ANY DAMAGE
(INCLUDING BUT NOT LIMITED TO DENTS, IMPACT MARKS, DEFORMATIONS IN PANELS, ETC.) FAILURE
TO DO SO MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. IF DAMAGE IS OBSERVED, UNPLUG
THE EQUIPMENT AND CONTACT THE MANUFACTURER IMMEDIATELY.
To ensure safe and proper use of the ChipCHECK system, Users of ChipCHECK must be aware of and
adhere to all safety precautions and procedures as discussed herein. Users shall use this section to
become acquainted with the specific safety features included with ChipCHECK system.
Laser Parameters:
Product Laser Classification
Class 1
Wavelength
1064nm
Laser Power / Peak Power
12mW / 600kW
Pulse Energy
1.2mJ
Emission Type
Pulsed
Optical Pulse Width
2ns
Beam Diameter (at aperture)
4.5mm
Divergence
< 0.8mRad
NOTE:
•Never use or operate the equipment without full understanding and compliance with this
Operator Manual.
•This Laser Product is designated as Class 1 during all procedures of operation.
•There is no scheduled maintenance required to keep the product in compliance.
•Refer to Section 6.0 for the allowable User maintenance.
•There is absolutely NO SERVICE ALLOWED by the User. There are no User serviceable parts.
•This equipment is to be serviced or repaired only by Gastops authorized technicians.
•The User is not allowed to attempt to alter, interfere, modify, remove, circumvent, defeat or
de-active any safety features or interlocks (see Section 2.2.2 and Figure 2-1 & 2-6).
•The User is strictly forbidden from reverse-engineering, altering, interfering, modifying,
removing, circumventing, or de-activing any part of the equipment.
•Never remove any labels or remove any covers.
Gastops Ltd.
C009423, Rev. 4 page 5
All use of this publication and ChipCHECK by user shall be subject to the restrictions and conditions as set out in this publication.
•Objects and/or material not required for operation must not be kept near the equipment
operating area.
•Keep the equipment dry at all times and avoid spilling liquid into the equipment. If any
liquids or spills enter the interior of the equipment, switch off power and contact Gastops
Customer Support (Section 8.0).
•Do not use flammable gases around the equipment or volatile gas or liquids inside the
equipment. Fire or explosions could result.
•Never use or operate the equipment if the equipment:
-Is defective, shows visible signs of damage, or was subject to events (including weather)
that could have damaged the equipment (non-visible damages)
-If any safety system feature or seal is damaged
-Fails to perform the intended measurement
-Has been subject to prolonged storage in unfavorable conditions
-Has been subject to severe transport stresses
If any of the above has occurred, then switch off the power and contact Gastops Customer Support
(Section 8.0).
2.2 Safety Features
This section describes the integrated safety features that ensure the User’s safety throughout the
operation of the equipment. It is these safety features that render the classification of this product as
Class 1. As a result, the User is strictly forbidden to alter, interfere, modify, remove, circumvent, defeat
or de-active any of these features. Refer to Figures 2-1 through Figures 2-5 below for a schematic
describing all of the integrated safety features. It is critical that the User becomes familiar with the
location and purpose of each safety feature in order to ensure safe use of the equipment.
Gastops Ltd.
C009423, Rev. 4 page 6
All use of this publication and ChipCHECK by user shall be subject to the restrictions and conditions as set out in this publication.
Figure 2-1: Location of all ChipCHECK Safety Features
2.2.1 Safety Labels
This section reviews all of the labelling information associated with the equipment. It is imperative that
the User becomes familiar with the labels, their location, and their meaning.
The following images depict all of the labels found on the equipment and within this document. Each
figure below has been assigned a number which corresponds to the label placement schematic below.
Refer to Figure 2-2 through Figure 2-5 below to become familiar with the specific location of each label.
Figure 2-2: Explanatory Label (1) – Not Found On Unit
Gastops Ltd.
C009423, Rev. 4 page 7
All use of this publication and ChipCHECK by user shall be subject to the restrictions and conditions as set out in this publication.
Figure 2-3: Explanatory, Manufacturer’s Identification, and Certification Label (2)
(Note that only one of the two shown above will be applied to the unit.)
Figure 2-4: Protective Housing, Non-Interlocked Label (3)
Gastops Ltd.
C009423, Rev. 4 page 8
All use of this publication and ChipCHECK by user shall be subject to the restrictions and conditions as set out in this publication.
Figure 2-5: Laser ChipCHECK Label Placement Schematic
(Numbers shown correspond to the label titles above)
2.2.2 Interlocks
The equipment is equipped with a forced contact redundant interlock system that provides the User
with the required level of safety when operating the equipment. The two interlocks in this system are
placed on the Sample Access Panel and ensure that power to the laser is severed prior to any opening
being made in the equipment during operation (i.e.: opening the Sample Door). Having these interlocks
ensures that the User is never exposed to laser radiation above a Class I classification. As a result, this
panel shall not be modified in any fashion, and the User is strictly forbidden from attempting to alter,
interfere, modify, remove, circumvent, defeat or de-active these safety interlocks.
Figure 2-6 indicates the location of the Sample Access Panel safety interlocks.
Gastops Ltd.
C009423, Rev. 4 page 9
All use of this publication and ChipCHECK by user shall be subject to the restrictions and conditions as set out in this publication.
Figure 2-6: Sample Access Panel Interlock (Location)
Autres manuels pour ChipCHECK CC120
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Gastops Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur