Garmin PANOPTIX Manuel utilisateur

PANOPTIX™ICE FISHING KIT

INSTALLATION INSTRUCTIONS

Assembling the Portable Mount

You need a Phillips screwdriver to assemble the portable mount.

1Insert the handle into the two openings on the portable mount base .

2Secure the handle to the base using the two 42 mm machine screws and two nuts .

3Slide the included hook and loop straps through the narrow slots beside the battery compartment.

4If you are installing a Panoptix LiveScope™ sonar module , using the eight included 21 mm screws , split

washers, and flat washers, attach the two included brackets to the module, and secure the brackets to

the portable mount.

5Align the chartplotter bail mount over the hole pattern that matches your bail mount, with the openings on

the top of the bail mount facing the back of the base.

GUID-C5E8D7D2-C09F-45FD-82BF-4470A5CE1713 v2March 2021

6Secure the device mount to the base using the four included 24 mm machine screws and the included

washers, if you are installing a metal bail mount.

NOTICE

Only use the included washers if you are installing a metal bail mount. If you are installing a plastic bail

mount, do not use the four included washers.

NOTE: Do not use the self-threading screws included with the chartplotter. Only use the machine-threaded

screws included with this portable kit or use M4 machine screws.

7Place the included rubber washers on the bail-mount knobs, and screw the knobs into the sides of the cradle

or chartplotter.

8Place the cradle or chartplotter into the bail mount, with the rubber washers between the knobs and the

cradle, and tighten the knobs.

The rubber washers enable you to adjust the viewing angle without adjusting the knobs.

9Place the battery (not included) into the battery compartment under the handle.

10 Pull the straps under and around the bottom of the portable mount, and wrap them tightly around the

battery.

Placing the Portable Mount in the Bag

After you have assembled the portable mount, you should place it in the bag, which makes it easier to carry and

protects it from the elements. The bag contains loops that allow you to tether the bag as needed.

1Place the portable mount into the bag.

2If necessary, wrap the excess power cable and transducer cables around the handle.

3Close all of the zippers.

You can use the zipper at the back of the bag for quick access to charge the battery. You can store the wall

charger in the interior zippered pocket, and store the transducer in the exterior side pocket.

Connecting the Cables

CAUTION

Ensure that you connect the correct spade connector to the correct battery terminal. Damage to the battery or

device, or bodily harm may occur if the device is improperly connected to the battery (not included).

1Obtain an appropriate power cable and transducer cable to use with your chartplotter and transducer.

The all-in-one power and transducer cable (010-12676-40) works with 7 inch or larger ECHOMAP™

chartplotters.

2Connect the 4-pin power cable and transducer cable to the chartplotter.

3If you are connecting a transducer, connect the power leads to the gray bare wire connectors on the power

cable.

4If you are connecting a Panoptix LiveScope sonar module, connect the 2-pin power cable to the sonar

module.

5Slide the red spade connector onto the positive (red) terminal on the battery.

6Slide the black spade connector onto the negative (black) terminal on the battery.

Limited Warranty

The Garmin® standard limited warranty applies to this accessory. For more information, go to www.garmin.com

/support/warranty.html.

Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. LiveScope™ and Panoptix™ are trademarks of

Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.

Table des matières

Autres manuels Garmin Sondeur de pêche

Garmin

Garmin Fishfinder 240 Blue Manuel utilisateur

Garmin

Garmin Fishfinder 120 Manuel utilisateur

Garmin

Garmin GWS 10 Marine Wind Sensor Manuel utilisateur

Garmin

Garmin STRIKER PLUS 5 Manuel utilisateur

Garmin

Garmin GPSMAP 580 Manuel utilisateur

Garmin

Garmin echo 300 Series Manuel utilisateur

Garmin

Garmin nuvi 150 series Manuel utilisateur

Garmin

Garmin Fishfinder 100 Manuel utilisateur

Garmin

Garmin PORTABLE ICE FISHING KIT Manuel utilisateur

Garmin

Garmin Fishfinder 400C Manuel utilisateur

Garmin

Garmin striker 4 Manuel utilisateur

Garmin

Garmin Fishfinder 400C Guide de référence

Garmin

Garmin ECHOMAP ULTRA 126s Manuel utilisateur

Garmin

Garmin Fishfinder 300C Manuel utilisateur

Garmin

Garmin Echo 100 Manuel utilisateur

Garmin

Garmin Fishfinder 250 Manuel utilisateur

Garmin

Garmin Fishfinder 80 Manuel utilisateur

Garmin

Garmin Fishfinder 80 Manuel utilisateur

Garmin

Garmin Fishfinder 160 Manuel utilisateur

Garmin

Garmin Fishfinder 140 Manuel utilisateur

Garmin

Garmin 101 Manuel utilisateur

Garmin

Garmin Fishfinder 240 Manuel utilisateur

Garmin

Garmin STRIKER Vivid 4 Manuel utilisateur

Garmin

Garmin Echo 100 Manuel utilisateur

Manuels Sondeur de pêche populaires d'autres marques

Norcross

Norcross D10DX.01T Manuel utilisateur

Hawkeye Mfg

Hawkeye Mfg FishTrax FT1PXC Manuel utilisateur

JRC

JRC JFV-700HP Manuel utilisateur

JRC

JRC FF50 Manuel utilisateur

Navman

Navman FISH 4200 Manuel utilisateur

Humminbird

Humminbird 140c Fishin' Buddy Manuel utilisateur

Furuno

Furuno FCV-628 Manuel utilisateur

Humminbird

Humminbird Tour Series Manuel utilisateur

Humminbird

Humminbird 585C Manuel utilisateur

Humminbird

Humminbird 595C Manuel utilisateur

Raytheon

Raytheon V720 Manuel utilisateur

Humminbird

Humminbird 400TX Manuel utilisateur

Norcross

Norcross ML100TDR ML100R ML100DR ML100tr Manuel utilisateur

Furuno

Furuno FCV-627 Manuel utilisateur

Fuso

Fuso FEG-881 Manuel utilisateur

Humminbird

Humminbird Matrix 47 Manuel utilisateur

Humminbird

Humminbird PiranhaMAX 165 Manuel utilisateur

Humminbird

Humminbird 586C Manuel utilisateur