Garmin GC 200 Manuel utilisateur
GC™200 IP MARINE CAMERA
INSTALLATION INSTRUCTIONS
Mounting Considerations
WARNING
See the Important Safety and Product Information guide in the product box for product warnings and other
important information.
You can mount the camera upside-down or sideways. You can reverse the camera image to use in rearview
mode. See your chartplotter owner's manual for instructions.
NOTE: You must update your chartplotter software to setup and view the camera feed on your chartplotter.
• You must mount the camera in a location where it is not submerged, does not present a hazard in doorways
or walkways, and cannot be damaged by docks, pilings, or other pieces of equipment.
• You should mount the camera in a location strong enough to support the weight of the device and where you
can remove the camera.
• You should mount the camera so the LED is visible and the cables can be connected easily.
• To avoid interference with a magnetic compass, do not mount the camera closer to a compass than the
compass-safe distance value listed in the product specifications.
• You should test the camera in the selected location before you permanently mount the camera.
• You can use the Garmin® Power Module to help make the installation easier. The Power Module uses a
single camera cable instead of separate power and ethernet cables. This is especially beneficial when the
camera is located far away from other electronics, such as near the bow or on a mast.
Tools Needed
• Drill and 2 mm (1/16 in.) drill bit
• Pozidriv® screwdriver
GUID-95567C20-B681-4E56-B4B1-71CF15B4972A v2August 2021
Mounting the Camera
1Secure the template to the mounting location.
2Using a 2 mm (1/16 in.) drill bit, drill the pilot holes.
3Using the included hex wrench, loosen the screw in the side of the camera base.
4Remove the base from the camera body.
5Feed the camera cables through the camera base, or through one of the cable channels.
6Align the camera base with the pilot holes, and secure the camera base with the washers and screws
.
7Attach the camera to the base, and tighten the screw in the camera base.
8Connect the camera cables.
9Align the slots on the camera base with the collar lugs , and turn the collar until it locks.
2
Connection Considerations
Connection Diagram with Direct Power
GC 200 marine IP camera
Garmin Marine Network cable small connector (included)
Garmin Marine Network Adapter Cable small to large (included)
9 to 18 Vdc power source (not included)
NOTICE
To avoid permanently damaging the camera, do not connect the camera directly to a 24 Vdc system.
You must use a Garmin Power Module when connecting to a 24 Vdc system.
1 A fast-acting fuse (required, not included)
NOTICE
You must connect the power wire through a 1 A fast-acting fuse (not included). Without a fuse, the
device can malfunction.
Garmin chartplotter (not included)
3
Connection Diagram with a Garmin Power Module
GC 200 marine IP camera
Garmin Marine Network cable small connector
Power module (010-12527-00, not included)
In-line switch (not included)
9 to 32 Vdc power source (not included)
Chartplotter (not included)
Camera Status LED
LED Activity Status
Solid red The camera is on.
Solid green The camera is connected to the network and transmitting data.
Flashing green The camera detects motion.
4
Specifications
Dimensions (Base W x H) 87 x 79 mm (3.4 x 3.1 in.)
Weight 520 g (1.2 lbs.)
Water rating IEC 60529 IPX71
Operating temperature range From -20 to 60°C (from 14 to 140°F)
Storage temperature range From -30 to 60°C (from -4 to 140°F)
Input voltage From 9 to 18 Vdc
Power module input voltage (not included) From 9 to 32 Vdc
Operating current with infrared on 370 mA
Operating current with infrared off 210 mA
Power consumption Max 5 W with infrared on
Fuse 1 A fast-acting (required for direct power connection, not
included)
Horizontal viewing angle 99.2 +/- 3 degrees
Vertical viewing angle 74 +/- 3 degrees
Infrared distance 30 m (98.4 ft.)
Compass-safe distance 10 cm (4 in.)
© 2021 Garmin Ltd. or its subsidiaries
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GC™ is a trademark of Garmin Ltd. or its
subsidiaries. These trademarks may not be used without the express permission of Garmin.
Pozidriv® is a trademark of the American Screw Company.
1 The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating.
5
© 2021 Garmin Ltd. or its subsidiaries support.garmin.com
Autres manuels pour GC 200
2
Table des matières
Autres manuels Garmin Appareil photo numérique
Garmin
Garmin BC 50 NIGHT VISION Manuel utilisateur
Garmin
Garmin BC 40 Manuel d'instructions
Garmin
Garmin DASH CAM 56 Manuel utilisateur
Garmin
Garmin GC 14 Manuel utilisateur
Garmin
Garmin XERO G1 Manuel d'instructions
Garmin
Garmin GC 100 Manuel utilisateur
Garmin
Garmin GDR 190 Manuel utilisateur
Garmin
Garmin BC 40 Manuel utilisateur
Garmin
Garmin BC 20 Manuel utilisateur
Garmin
Garmin BC 40 Manuel d'instructions
Garmin
Garmin BC 35 Manuel utilisateur
Garmin
Garmin BC Manuel utilisateur
Garmin
Garmin VIRB Ultra 30 Manuel d'instructions
Garmin
Garmin DASH CAM 47W Manuel utilisateur
Garmin
Garmin BC 50 Manuel utilisateur
Garmin
Garmin GC 12 Manuel utilisateur
Garmin
Garmin VIRB Series Manuel utilisateur
Garmin
Garmin BC 30 Manuel d'instructions
