Fytech FY-2012S Manuel utilisateur

Owner’s Manual

FY-2012S

The equipment is approved by following car manufacturers(China)

Multifunctional Automotive Plastic Welder

Contents

1、Safety Precaution Symbols

2、Installation

1)Specifications

2)Duty Cycle and Overheating

3)Machine Installation

3、Controls

Control Panel Instruction

4、Staple Gun

Staple Gun and Adapter

5、Operation

1)Tools Selection

2)Preparation, Making Repair

Page.1

Safety Precautions Symbols

Protect yourself and others from injury,

read and follow these precautions before

installation and operation.

Exploding parts can injure.Always wear a face

shield and long sleeves。

Static can damage PC boards

1、Put on grounded wrist strap before

handing boards or parts。

2、Use proper static-proof bags and boxes to

store，move or ship PC boards。

1、Wear approved face shield or safety goggles

with side shields。

2、Wear proper body protection to protect skin。

Do not weld in the height！

Read instructions.

1、Read owner's Manual before using or servicing

unit。

2、Use only manufacturer’s supplied replacement。

Flying metal can injure eyes。

1)Wear safety glasses with side shields or face

shield。

1、Magnetic fields can affect pacemakers.

Pacemaker wearers keep away.

2、Wearers should consult their doctor before

going near plasma arc cutting operations。

Overuse can cause overheating

Allow cooling period ,follow rated duty cycle

before starting to weld again.

Electric shock can kill:

1、Do not touch live electrical parts。

2、Wear dry,hole-free insulating gloves and

body protection.

3、Do not wrap electrical cable around your

body.

4、Ground the workpiece with a good electr-

ical ground。

Eye protection for welding:

Current level in amperage Minimum shade

Number

30-150A--------- - -- - - - -- - - - -- -- - -- - #8

150-300A-------- - -- - - - -- - - - -- -- - -- - #10

300-500A--------------------------- #12

Never cut on pressurized cylinder.

Maintenance regularly！

Factory safety！

Fire or explosion hazard.

Do not locate unit on,over,or near combustibe

surfaces.Do not install unit near flammables.

Remove all flammables of the welding area.

Falling unit can cause injury.

The heat from the workpiece can cause serious

burns。

Fumes and gases can be hazardous

welding produces fumes and gases. Breathing

these fumes and gases can be hazardous

to your health .

If inside,ventilate the area.

Do not weld in a confined space only if it

is well ventilated.

Protect yourself Warn others

NO.2

FY-2012S

AC220V 50/60Hz

1.5A

2.6V

5-30A

4.8kg

250x180x135mm

1. Specifications

Model

Input Voltage

Input Current

Output Voltage

Output Current

Weight

Measurement

Installation

N O . 3

2、Duty Cycle and Overheating

1. The system will automatically shut off the welder when a pre-

programmed temperature is reached. Automatic alert will be shown on

the display.

2. The welder can be used again after cooling down.

Overheating Stop working Wait fifteen minutes

for unit to cool

Reduce amperage or

reduce duty cycle

Weld again

N O . 4

3、Machine Installation

1) Open the package and find out the owners manual。

2) Check the supplied accessories according to packing list

that attached to this manual.

3) Properly install this equipment as following diagram.Inspect

the unit for any problems.If so, contact your local distributor

or service agency.

N O . 5

1 2 3 4

1, 2, 3, 4: Temperature adjustment

5: Display

6: Temperature decrease

7: Temperature increase

Operation

1、Controls

N O . 6

123

Staple Gun

1. Trigger switch

2. Electrode

3. Electrode adapter

4. Staple

5. Staple

6. Hole locations of contact prong

1. Staple gun and adapter

N O . 7

A B C D E

A. Reinforcing cracks at inside corners, curved areas and

other complex shapes.

B. Repairing cracks in rigid plastic.

C. Repairing multiple cracks and complete breaks in rigid

plastic.

D. Cutting off staple legs

E. Polishing surface

Operation

1. Tool Selection

N O . 8

Operation

2. Preparation

Always clean the plastic part surface being repaired of any grease,

dirt, film or other contaminates before beginning.

3. Making Repairs

Plug the power cord into a grounded outlet. Place the desired staple

configuration into one of three hole locations in the contact prongs,

choosing the hole location that provides the best access to the

damage. Do not press the trigger switch. The staple will achieve full

heat after pressing the trigger switch.

Set the Temperature to suit the material being repaired.

Step “1” for thinner and softer plastics.

Step “2” and “3” for thicker and semi-rigid plastics.

Step '4” for thick and hard plastics.

Usually setting the temperature to the step “2” or “3” is recommended.

CAUTION: On thinner and softer materials, it is very easy to burn

through to the outer surface, do not use excessive force.

Application

Press and hold the trigger switch on the Staple Gun for 10 seconds

allowing the staple to achieve full heat. Carefully press the heated

staple gently into the plastic keeping the staple parallel and square to

the surface while continuing to hold the trigger switch.

When the staple is satisfactorily burrowed into the material, release

the trigger switch, wait several seconds to allow the molten plastic to

firm up then withdraw the staple gun from the staple.

When done, the staple legs can be cut off with side cutters then

ground down to the repaired surface area.

Table des matières

Autres manuels Fytech Système de soudage

Fytech

Fytech FYMIG200L-2 Manuel utilisateur

Fytech

Fytech FY-9000A Manuel utilisateur

Fytech

Fytech FY-4250/2E Manuel utilisateur

Fytech

Fytech FY-92G Manuel utilisateur

Fytech

Fytech FY-5000 Manuel utilisateur

Fytech

Fytech FY-9000 Manuel utilisateur

Fytech

Fytech FY-8L Manuel utilisateur

Fytech

Fytech FY-5015L Manuel utilisateur

Fytech

Fytech FY-7000 Manuel utilisateur

Fytech

Fytech FY-2270/2E Manuel utilisateur

Fytech

Fytech FY-8000 Manuel utilisateur

Fytech

Fytech FY-13000 Manuel utilisateur

Fytech

Fytech FYMIG305L Manuel utilisateur

Fytech

Fytech FY-4DM Manuel utilisateur

Fytech

Fytech FY-4500 Manuel utilisateur

Fytech

Fytech FYMIG5215X Manuel utilisateur

Fytech

Fytech FYMIG300 Manuel utilisateur

Fytech

Fytech FYMIG306L Manuel utilisateur

Fytech

Fytech FYMIG210X Manuel utilisateur

Fytech

Fytech FYMIG306XL Manuel utilisateur

Fytech

Fytech FYMIG307 Manuel utilisateur

Fytech

Fytech FY-4220/2E Manuel utilisateur

Fytech

Fytech FY-3180A Manuel utilisateur

Fytech

Fytech FY-6G Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

ESAB

ESAB Buddy Arc 145 Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

Miller

Miller Big Blue 400D Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur