FUTABA FX-20 Manuel utilisateur

FX-20-2.4G

Futaba Corporation

FX-20

Radio Control

Instruction Manual

INTRODUCTION

Thank you for purchasing a Futaba digital proportional R/C system. In order for you to make the

best use of your system and to use it safely, please read this manual carefully. If you have any

difficulties while using your system, please consult the manual, our online Fre uently Asked

Questions (on the web pages referenced below), your hobby dealer.

Owner’s Manual and Additional Technical Help

This manual has been carefully written to be as helpful to you, the new owner, as possible.

There are many pages of setup procedures and examples. However, it need not be your sole

resource of setup guidelines. For example, the back cover includes a uick-start set of

instructions and the Fre uently Asked Questions web page referenced below includes this type

of step-by-step setup instructions for a variety of other model types.

Due to potential unforeseen changes in production procedures, the information contained in this

manual is subject to change without notice. No part of this manual may be reproduced in any

form, at any time, without prior permission.

Support and Service: It is recommended to have your Futaba e uipment serviced annually

during your hobby’s “off season” to ensure safe operation.

FX-20-2.4G

Futaba Corporation

IN NORTH AMERICA

Please contact Uwe Frank Heinrich to assist you with any questions, problems or

service needs.

Uwe Frank Heinrich

1214 SW 39

Street

Cape Coral, FL 33914

Phone: 239-54 -7872

Cell: 239-223-8581

OUTS DE NORTH AMER CA

Please contact your Futaba importer in your region of the world to assist you with any

questions, problems or service needs.

Please recognize that all information in this manual, and all support availability, is

based upon the systems sold in North America only. Products purchased elsewhere

may vary. Always contact your region’s support center for assistance.

FX-20-2.4G

Futaba Corporation

Federal Communications Commission Interference Statement (for U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. f this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-- ncrease the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

--Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

To assure continued FCC compliance:

Any changes or modifications not expressly approved by the grantee of this device could void

the user's authority to operate the equipment.

Exposure to Radio Frequency Radiation

To comply with FCC RF exposure compliance requirements, a separation distance of at least

20cm must be maintained between the antenna of this device and all persons.

This device must not be co-located or operating in conjunction with any other antenna or

transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

FX-20-2.4G

Futaba Corporation

Instruction of the FX

Instruction of the FXInstruction of the FX

Instruction of the FX-

-20

2020

20-

-2.4G

2.4G2.4G

2.4G

1.Location

Fig. Front view

Fig. si e view

Touch sensor

Power Switch

Right Stick

Left Stick

LCD

DSC connector

Charge jack

SD car slot

FX-20-2.4G

Futaba Corporation

Fig. Bottom view

Fig. Insi e view (Battery box)

2.2.

2.Charging the battery

Charging the batteryCharging the battery

Charging the battery

1-1. Please confirms the power switch is off.

1-2. Insert the plug of the charger to charging bush of transmitter.

1-3. During the charging, the LED of the charger is on.

The charging time is appx. 15 hours. Please o not charge the battery for 15hours or more.

The overcharge amages the battery.

The battery is 6 cells Ni-MH battery the capacity is 7.2 V/ 1,700mAH.

Sli er

MH battery

FX-20-2.4G

Futaba Corporation

３．

３．３．

３．Operation of the touch sensor

Operation of the touch sensorOperation of the touch sensor

Operation of the touch sensor

Contents Operation

Touch

part

Con ition Working

At the screen have some pages.

(Ex. P-MIX screen)

The cursor jumps to top of next

page

At the screen have Only one(１)

page.

The cursor jumps the top of page.

At the input ata mo e with

blinking the setting ata.

The setting ata is cancele .

At the moving cursor mo e. Change to the input ata mo e.

At the input ata mo e. Change to the moving cursor mo e.

Short touch

RTN

At the input ata mo e with

blinking the setting ata.

The ata is entere .

Home screen,

System menu,

Linkage Menu,

Mo el menu,

Selecting ON/OFF Switch,

USER NAME,

MODEL NAME,

DISPLAY, INFO,

MODEL SELECT,

MODEL TYPE,

FREQUECY,

DATA RESET,

TIMER,

Selecting Control,

Selecting Function,

SERVO MONITOR

Jump to “System Menu” screen

irectly.

SYS

Except of above Jump to “SERVO MONITOR”

screen irectly.

LNK At all screens Jump to “Linkage Menu” screen

irectly.

MDL At all screens Jump to “Mo el Menu” screen

irectly.

HOME screen Key lock On or Off S1

Except the HOME screen Jump to HOME screen irectly.

RTN At the input ata mo e with

blinking the setting ata.

Entere ecision.

Long touch（1 secon ）

At the input ata mo e without

blinking the setting ata.

Reset to the initialize value.

Scrolling Outline At the moving cursor mo e The cursor is move .

FX-20-2.4G

Futaba Corporation

of “RTN”

Input ata mo e Increment or ecrement the ata.

Select Yes or No, an so on.

4.4.

4.Turns on the transmitter

Turns on the transmitterTurns on the transmitter

Turns on the transmitter

4-1 Power switch is to be on. The re LED is light. LCD isplays the bar graph at moment.

4-2 Then, LCD isplays the Home screen imme iately.

FX-20-2.4G

Futaba Corporation

5．

．．

． Basic operation of

Basic operation of Basic operation of

Basic operation of e iting

e itinge iting

e iting

LCD screen is consists of e iting button an monitor isplay. You can go through e iting menu

by touch sensor. If you want t o go back to previous menu, you move the cursor to screen title

an touch “RTN”.

6.6.

6.Home screen

Home screenHome screen

Home screen

You always enter this screen after turning on the power. It is a base screen to e it.

1. User Name 8. Mo e (MULT / 7CH)

2. Timer #1 9. Timer #2

3. Mo el Name 10.

Trim In icator

4. Clock icon (Jump to timer screen) 11.

Mo el Type Icon

5. Integrate Timer 12.

Memory Car Icon (at etecte car )

6. Mo el Timer 13.

RF Transmit

7. Battery Gauge

FX-20-2.4G

Futaba Corporation

7.7.

7.Linkage menu

Linkage menuLinkage menu

Linkage menu

The linkage menu sets the primary ata of the each mo el. These ata are common to every

flight con ition.

If you touch “LNK” of the touch sensor over 1 secon , you can get into the linkage menu screen.

8.8.

8.Mo el Menu

Mo el MenuMo el Menu

Mo el Menu

The mo el menu sets the ata of mixer. These ata of each flight con ition can be set.

If you touch “MDL” of the touch sensor over 1 secon , you can get into mo el menu screen.

9.9.

9.System Menu

System MenuSystem Menu

System Menu

The system menu sets the transmitter setting ata. For example, isplay contrast, stick mo e.

If you touch “SYS” of the touch sensor over 1 secon , you can get into system menu screen

FX-20-2.4G

Futaba Corporation

Specification

SpecificationSpecification

Specification

FX-20-2.4G SPEC F CAT ONS

1 Ra io Characteristics

Engineering stan ar Part 15.247 FCC (U.S.)

RF power output 50mW

Mo ulation Direct-Sequence Sprea -Spectrum

Communication scheme Single communication

Frequency ban 2405.376MHz - 2477.056MHz (general mo e)

2407.424MHz - 2450.432MHz (France mo e)

Channel 36 or 22

Data barer rate 136 kbps

Frequency control Crystal controlle frequency synthesizer

Antenna 1/2λ Pencil type antenna 1.5 Bi (MAX)

2 Ra io communication control

Error checking CRC-CCITT

3 Terminal interface

Physical interface none

4 Power Supplying

Supply voltage 7.2V DC

Current consumption 250 mA

5 Environmental

Operating temperature -10 to +45 ℃

Storage temperature -20 to +60 ℃

6 Miscellaneous

In icator LCD isplay, 2 LED

Frequency setting programmable

Case Plastic

Outer imensions 220(W)×210(D)×64(H) mm

Weight Approx. 740g

Table des matières

Autres manuels FUTABA Télécommande

FUTABA

FUTABA T12Z Manuel technique

FUTABA

FUTABA 14MZ Manuel utilisateur

FUTABA

FUTABA T14SG Manuel technique

FUTABA

FUTABA T-FHSS Air-2.4GHz 10J Series Manuel utilisateur

FUTABA

FUTABA 6XA Manuel utilisateur

FUTABA

FUTABA FP-8SSHP Manuel utilisateur

FUTABA

FUTABA FASSTest-2.4GHz T16SZ Series Manuel utilisateur

FUTABA

FUTABA 16IZ Manuel d'utilisation et d'entretien

FUTABA

FUTABA FP-2PB Manuel utilisateur

FUTABA

FUTABA 4pls Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART1 Manuel utilisateur

FUTABA

FUTABA AZPT14SG-24G Manuel utilisateur

FUTABA

FUTABA T14SG Manuel technique

FUTABA

FUTABA FP-G134 Manuel utilisateur

FUTABA

FUTABA FP-3FN Manuel utilisateur

FUTABA

FUTABA CONQUEST Manuel utilisateur

FUTABA

FUTABA 14MZ Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation

FUTABA

FUTABA S.BUS2 10J Manuel utilisateur

FUTABA

FUTABA 4PK-2.4GHZ Manuel utilisateur

FUTABA

FUTABA T18SZ Manuel utilisateur

FUTABA

FUTABA 3GR-2.4GHZ Manuel utilisateur

FUTABA

FUTABA FASSTest-2.4GHz T16SZ Series Manuel utilisateur

FUTABA

FUTABA T10J Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

Invacare

Invacare G91S Manuel utilisateur

JR Racing

JR Racing XR2 Manuel utilisateur