Furuno GP-150 Manuel utilisateur
INSTALLATION MANUAL
GPS NAVIGATOR
GP-150
1. SYSTEM CONFIGURATIONS .......................................................................... 1
2. EQUIPMENT LIST............................................................................................ 2
3. DISPLAY UNIT .................................................................................................. 4
4. ANTENNA UNIT ................................................................................................ 6
5. WIRING ........................................................................................................... 10
6. INITIAL SETTINGS ......................................................................................... 12
7. OPTIONAL DGPS........................................................................................... 23
PACKING LISTS & INSTALLATION MATERIALS........................................... A-1
OUTLINE DRAWINGS ...................................................................................... D-1
INTERCONNECTION DIAGRAM ......................................................................S-1
www.furuno.co.jp
SAFETY INSTRUCTIONS
WARNING
Do not work inside the
equipment unless totally
familiar with electrical
circuits.
Hazardous voltage which can
cause electrical shock, burn
or serious injury exists inside
the equipment.
Turn off the power at the
mains switchboard before
beginning the installation.
Post a sign near the switch
to indicate it should not be
turned on while the equip-
ment is being installed.
Fire, electrical shock or
serious injury can result if the
power is left on or is applied
while the equipment is being
installed.
Ground the display unit to
prevent loss of sensitivity
and mutual interference.
Confirm that the power supply voltage
is compatible with the voltage rating
of the equipment.
Connection to the wrong power supply
can cause fire or equipment damage. The
voltage rating appears on the label at the
rear of the display unit.
Use the correct fuse.
Use of a wrong fuse can cause fire or
equipment damage.
Keep the following compass safe
distances:
Standard Steering
Display unit 0.50 m 0.35 m
CAUTION
This page is intentionally left blank.
1
1. SYSTEM CONFIGURATIONS
Antenna Unit GPA-018S*
Display Unit
Radar, Echosounder,
Autopilot etc.
DGPS Beacon
Receiver
GR-80**
12-24VDC
Antenna Unit GPA-017S**
Antenna Unit GPA-019S*
*: w/internal beacon receiver
**: w/o internal beacon receiver
2
2. EQUIPMENT LISTS
Standards
Name Type Q'ty Remarks
GPA-017S
GPA-018S
Antenna Unit
GPA-019S
1 For DGPS
GP-150-E-N Without Beacon RX
Display Unit GP-150-E-A 1 With Beacon RX
CP20-01900 With Antenna CableInstallation
Materials CP20-01950 1 set Without Antenna Cable
Accessories FP20-01100 1 set
Spare Parts SP20-00500 1 set
See lists
at end of
manual.
Options
Name Type Code No. Remarks
Flush Mount Kit S OP20-24 004-393-000
Flush Mount Kit F OP20-25 004-393-280 For display unit.
CP20-01700 004-372-110 CP20-01701+30 m cable
CP20-02700 004-381-160 CP20-02701+30 m cable
CP20-01710 004-372-120 CP20-01701+50 m cable
Antenna Cable Set
CP20-02710 004-381-170 CP20-02701+50 m cable
Antenna Cable Assy. TNC-PS-3D-15 000-133-670 15 m
Right Angle Antenna
Base No.13-QA330 000-803-239
L-Type Antenna Base No.13-QA310 000-803-240
Handrail Antenna Base No.13-RC5160 000-806-114
Mast Mount Kit CP20-01111 004-365-780
For antenna unit.
MJ-A6SPF0011-050C
(03S9202) 000-159-690-10 Cross Cable 5m, 6P-4P
MJ-A6SPF0011-100C
(03S9226) 000-159-691-10 Cross Cable 10m, 6P-4P
MJ-A7SPF0003-050C
(20S0241) 000-159-688-11 5m, For DATA4
MJ-A6SPF0003-050C
(20S0093) 000-154-054-10 5m
MJ-A6SPF0012-050C
(64S4073) 000-154-053-10 Cross cable 5m
Cable Assy
MJ-A6SPF0012-100C
(64S4071) 000-154-037-10 Cross cable 10m
2. EQUIPMENT LISTS
3
(Continued from the previous page)
OP20-32-1 000-041-018 With GPA-018S
OP20-32 000-041-019 With whip antenna and OP20-32-1
OP20-33 000-041-596 With GPS-019S
Beacon Receiver Set
OP20-34 000-041-598 Without whip antenna
000-013-485 For 100VAC mains
Rectifier PR-62 000-013-486 For 220VAC mains
DGPS Beacon Receiver GR-80 -
Whip Antenna FAW-1.2 000-130-046 1.2 m
Printer PP-505-FP 000-011-792
Data Switch Box MD-200 -
4
3. DISPLAY UNIT
The display unit can be installed with either of four methods as shown below. Refer to the
outline drawing at the end of manual.
• Locate the unit away from exhaust pipes and vents.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• Keep the display unit away electromagnetic field generating equipment such as motor,
generator.
• Allow sufficient maintenance space and a sufficient slack in cables for maintenance and
repair.
Table Top and Overhead Mounting
TABLETOP OVERHEAD
Display unit mounting methods
Flush mounting type F
An optional flush mount kit type F is required. For details, see outline drawing at end of this
manual. (Name: Flush Mount Kit F, Type: OP20-25, Code No.004-393-280)
Name Type Code No. Qty
Self-tapping screw 5X20 000-162-609-10 4
Hex. bolt M6X12 SUS304 000-162-897-10 2
Spring washer M6 SUS304 000-158-855-10 2
Cosmetic panel 20-013-1121 100-234-240 1
3. DISPLAY UNIT
5
Flush mounting type S
An optional flush mount kit type S is required. (Name: Flush Mount Kit S, Type: OP20-24,
Code No.: 004-393-000)
Name Type Code No. Qty
Wing bolt M4X30 YBSC2 000-804-799 4
Hex. bolt M6X12 SUS304 000-162-897-10 2
Wing nut M4 YBCS2 000-863-306 4
Spring washer M6 SUS304 000-158-855-10 2
Flush mount metal 20-013-1111 100-234-230 2
1. Prepare a cutout in the mounting location whose dimensions are 242 (W) X 152 (H) mm.
2. Insert the unit to the cutout.
3. Attach two flush mount metals to the unit with two hex bolts (M6X12) and two spring
washers.
4. Screw four wing bolts to wing nut.
5. Fasten the unit with wing bolts assembled at step 4, and then tighten nuts.
6
4. ANTENNA UNIT
Mounting
Install the antenna unit referring to the installation diagram at end of manual. When
selecting a mounting location for the antenna unit, keep in mind the following points.
• Select a location out of the radar beam. The radar beam will obstruct or prevent reception
of the GPS satellite signal.
• Be sure the location offers a clean line-of-sight to satellite. Objects within line-of-sight to
a satellite, for example, a mast or funnel, block reception and cause prolonged acquiring time
or interruption of position fix.
• Mount the unit as high as possible. Mounting the antenna as high as possible keeps it free
of water spray, which can intercept reception of GPS satellite signal, if water spray is frozen.
• The antenna unit GPA-018S must be grounded. Connect ground wire of 1.25 sq or larger
(local supply) between the antenna unit and a stainless steel screw fastened to the mast.
• The antenna unit GPA-018S must be taped. See next page.
• The antenna unit should be fixed to the mast as below.
Coat here with silicone sealant to
prevent breakage of the cable by
vibration.
Wrap the vinyl sheet to prevent
the breakage of the cable, and
then fix it with a hose clamp.
Autres manuels pour GP-150
4
Table des matières
Autres manuels Furuno GPS
Furuno
Furuno GP-80 Manuel utilisateur
Furuno
Furuno 1954C Manuel
Furuno
Furuno GP-39 Manuel utilisateur
Furuno
Furuno GP-150 Manuel utilisateur
Furuno
Furuno GP-330B Manuel utilisateur
Furuno
Furuno GP-150 Manuel utilisateur
Furuno
Furuno GP-7000 Manuel utilisateur
Furuno
Furuno GP-330B Manuel utilisateur
Furuno
Furuno FAP-50 Manuel utilisateur
Furuno
Furuno GP-1670F Guide de démarrage rapide
Furuno
Furuno GP-70 Manuel utilisateur
Furuno
Furuno Felcom 82 Manuel
Furuno
Furuno GP-7000 Manuel utilisateur
Furuno
Furuno GP-170 Manuel utilisateur
Furuno
Furuno GPS Navigator GP-500 MARK-2 Manuel utilisateur
Furuno
Furuno GP-320B Manuel utilisateur
Furuno
Furuno FBA3 Manuel utilisateur
Furuno
Furuno GR-80 Manuel utilisateur
Furuno
Furuno GP-500 Manuel utilisateur
Furuno
Furuno GP-150 Manuel
