Fujitsu PRIMERGY TX150 S6 Mode d’emploi
CA92276-8243-01
Note on using PRIMERGY TX150 S6
Thank you for purchasing our product. Before you start using your server, please
carefully read the additional notes described below.
June 2008
FUJITSU LIMITED
1．Warning Messages of ServerView Remote Connector when start up the OS
[Symptom]
If following all conditions are met, the warning message below would be recorded on Application
Event Log when start up the server.
Type: Warning
Source:ServerView Remote Connector
Event ID: 0
Description:
Initialization not completed timely (0 seconds)
[Conditions]
1) ServerView Agent for Windows is installed
2) The system is highly-loaded for start up
[Cause]
Because the system is highly-loaded for start up, initializing process of ServerView Remote
Connector is delayed. This warning is to notify the service start up is not completed while certain
period of time. This message is not for failure notice of service start up.
[Remedy]
Even if the message is recorded because of the process delay as above, the service keeps running
the initializing process. The service will automatically start after complete the initializing process
of ServerView Remote Connector. No special handling is required.
* ServerView Remote Connector service is used as the service at the Performance Manager of ServerView.
Even though this service is not active, there is no effect to the function other than Performance Manager.
Note: how to confirm
Please follow the steps below to confirm ServerView Remote Connector service runs normally.
－ Start the Performance Manager from the ServerView S2.
－ Select the server of which you want to confirm the performance from the left side frame.
－ Select the <Report View> tab.
－ Select any report, and click the” Show >>” button.
If the graphics is displayed, ServerView Remote Connector service runs normally. Please use it without
any change. If the service is not a normal run, the dialog box as below will be displayed.
All Rights Reserved, Copyright© FUJITSU LIMITED 2008
1／8
Note: It is necessary to set the report setting beforehand.
For direction of Performance Manager, please refer to "ServerView User's Guide".
If the ServerView Remote Connector is not a normal run, please reboot the service with following
process. (There is no necessity to reboot the system.)
[Control Panel] - [Administrative Tools] - [Services] - [ServerView Remote Connector]
Do <Restart> the service
2． Updates for "PRIMERGY TX150 S6 User's Guide"
Chapter 4 "4.3 Storing the System Configuration Information"
4.3.1 Storing the BIOS Information and the Remote Management Controller Information (Page 82)
Deletion Please delete following notes.
Do not input the file extension at the end of a file name.
The file name is given as "cmosfile" when a file name is not input.
4.3.2Recovering the BIOS / Remote Management Information (Page 83 - 84)
Correction There is a misspelling on the command line.
4 Enter the following command and press the [Enter] key.
False: A:¥SMT>BIOSRESET.bat
True: A:¥SMT>BIOSREST.bat
Deletion Please delete following notes.
Do not input the file extension at the end of a file name.
The file name is given as "cmosfile" when a file name is not input.
4.3.2 Recovering the BIOS / Remote Management Information (Page 83)
Deletion Please delete following misdescription.
Server Management Tools disk is required to be created when mentioned as empty "blank" on the label of the "Server
Management Tools" disk, supplied with the server. Create Server Management Tools by referring to "4.4 Creating
Maintenance Tools and Driver Disks" (pg.85).
All Rights Reserved, Copyright© FUJITSU LIMITED 2008
2／8
Chapter 6 "6.2 Removing and Attaching Covers"
6.2.1 Removing Covers
■Attaching covers (Page 116)
Addition Following caution notes are added for attaching the cover description.
Before attaching the covers, flip the front cover and make sure the position of the key lock part (Point A) is
settled at the
proper position
. If the key lock part is not at the
proper position
, resetting the part before
attaching the covers are required. It may cause a breakage failure if you attach the covers and lock the key
with wrong position.
back side the front covers
All Rights Reserved, Copyright© FUJITSU LIMITED 2008
3／8
Close-up of point A
Point Ａ
Improper Position
Key lock part is unhooked (yellow circle).
Proper Position
Key lock part is hooked.
All Rights Reserved, Copyright© FUJITSU LIMITED 2008
4／8
Chapter 6 "6.6 Installing 5-inch Internal Options"
6.6.2 Installable 5-inch Internal Devices (Page 136)
Correction Please correct the list of installable 5-inch internal devices by adding 2 units.
False:
Unit type Product name Product ID Cable (separate) SCSI ID
Internal DAT72 unit Tape Drv DAT72 36GB internal PG-DT5041 －－
Internal LTO3 unit Tape Drv LTO3 Ultrium3/ Ultrium2
400GB PG-LT302 PG-CBLS027 5
True:
Unit type Product name Product ID Cable (separate) SCSI ID
Internal DAT72 unit Tape Drv DAT72 36GB internal PG-DT5041 －－
Internal LTO unit Tape Drv LTO Ultrium1 100GB PG-LT102 PG-CBLS027 5
Internal LTO2 unit Tape Drv LTO2 Ultrium2 200GB PG-LT201 PG-CBLS027 5
Internal LTO3 unit Tape Drv LTO3 Ultrium3/ Ultrium2
400GB PG-LT302 PG-CBLS027 5
6.9 Connecting External SCSI Devices (Page 146)
Correction There are misdescription about the product ID and length of cables.
Connecting Backup Cabinet
False: PG-CBLS001（1.5m）
PG-CBLS002（5m）
True: PG-CBLS007 (1.8m)
PG-CBLS008 (5m)
7.2.7 Advanced Processor Options submenu (Page.158)
Correction Please correct the following table for BIOS settings.
False)
table: Items on the Advanced Processor Options submenu
Item Setting Description
Enhanced SpeedStep Disabled（Unchangeable） Sets whether to enable or disable the power saving
function.
Enhanced Idle Power State Disabled（Unchangeable） Configures the CPU internal setting. This item is
displayed only when Xeon 3065/3085 processor is
onboard.
Virtualization Technology ・Disabled（Initial value）
・Enabled
Sets whether to enable or disable Virtualization
Technology.
True)
table: Items on the Advanced Processor Options submenu
Item Setting Description
Enhanced SpeedStep ・Disabled(Initial value)
・Enabled
Sets whether to enable or disable the power saving
function.
This item is changeable only when Windows system is
installed.
Enhanced Idle Power State Disabled（Unchangeable） Configures the CPU internal setting. This item is
displayed only when Xeon 3065 / 3085 / X3320 /
E3110 / Core2Duo E4600 processor is onboard.
Virtualization Technology ・Disabled（Initial value）
・Enabled
Sets whether to enable or disable Virtualization
Technology. This item is displayed only when Xeon
3065 / 3085 / X3210 / X3320/ E3110 processor is
onboard.
All Rights Reserved, Copyright© FUJITSU LIMITED 2008
5／8
7.2.9 Security Menu (Page. 160)
Correction
False)
True)
7.2.9 Security Menu(Page 161)
Addition
table: Items on the Security menu
Item Setting Description
・・・
System Password Lock ・Standard（Initial value）
・WOL SKIP
Sets whether to enter a password or not when
turn on by Wakeup On LAN.
TPM (Security Chip)
Setting
Configures the TPM (Security Chip) settings.
Press the [Enter] key to display the TPM(Security Chip) Setting submenu.
Virus Warning Disabled（Unchangeable） Sets whether or not to check the boot sector of the
hard disk drive after the previous system startup.
If the boot sector is changed without a clear
reason, it is necessary to scan the system for
computer viruses with a virus detection program.
・・・
table: Items on the TPM(Security Chip) Setting submenu
Item Setting Description
Security Chip ・Disabled（Unchangeable）
・Enabled
Configure the Security Chip setting..
Current TPM State Display the current TPM State.
Change TPM State
・No Change（Initial value）
・Enable&Activate
・Disable&Deactivate
・Clear
Change the TPM State. This item is displayed only
when Security Chip setting is enabled.
7.2.15 Console Redirection Submenu (Page 166)
Correction
False)
table: Items on the Console Redirection submenu
Item Setting Description
Console Redirection ・Disabled (Initial value)
・On-board COM A
・On-board COM B
Sets whether to enable or disable console redirection.
When set to [On-board COM A] or [On-board COM
B], the following parameters appear. Set each
parameter.
True)
table: Items on the Console Redirection submenu
Item Setting Description
Com Port Address ・Disabled (Initial value)
・On-board COM A
・On-board COM B
Sets whether to enable or disable console redirection.
When set to [On-board COM A] or [On-board COM
B], the following parameters appear. Set each
parameter.
All Rights Reserved, Copyright© FUJITSU LIMITED 2008
6／8
Appendix A Server Specifications (Page 204)
A.1 SAS Model (Page 204)
Correction
False)
True) table: Server specifications-SAS Model
Item Functions and specifications
Product name PRIMERGY TX150 S6 SAS model
Product ID PGUT1564A
Chipset Intel 3210/ICH9R®
Intel® CoreTM 2
Duo Processor Dual Core Intel® Xeon Processor
Type E4600
(2.40GHz)
3065
(2.33GHz)
E3100
(3GHz)
X3220
(2.40GHz)
X3320
(2.50GHz)
Number of cores 2 4
L2 Cache Size 2MB 4MB 6MB 2x4MB 6MB
FSB 800MHz 1333MHz 1066MHz 1333MHz
CPU
Number of CPUs Standard :1(Maximum:1)
Security chip Complied with TCG 1.2
■ Supported OS（Page 205）
Addition
The supported operating systems for this server are as below.
• Windows Server 2003, Standard Edition (SP2 or later)
• Windows Server 2003, Standard x 64 Edition (SP2 or later)
• Windows Server 2003 R2, Standard Edition (SP2 or later)
• Windows Server 2003 R2, Standard x64 Edition (SP2 or later)
• Windows Small Business Server 2003 R2 (SP2 or later)
• Windows Small Business Server 2003 (SP2 or later)
• Windows Server 2008 Standard (32-bit)
• Windows Server 2008 Standard (64-bit)
• Red Hat Enterprise Linux ES (v.4 for x86)
• Red Hat Enterprise Linux ES (v.4 for EM64T)
• Red Hat Enterprise Linux 5 (for x86)
• Red Hat Enterprise Linux 5 (for Intel64)
For details of Windows Server 2008, refer to the "Support Matrix" at the following URL:
http://www.fujitsu.com/downloads/PRMRGY/support-matrix.pdf
All Rights Reserved, Copyright© FUJITSU LIMITED 2008
7／8
A.1 SAS Model (Page 206)
Correction
False)
True) table: Server specifications-SATA Model
Item Functions and specifications
Product name PRIMERGY TX150 S6 SATA model
Product ID PGUT1564B
Chipset Intel 3210/ICH9R®
Intel® CoreTM 2
Duo Processor Dual Core Intel® Xeon Processor
Type E4600
(2.40GHz)
3065
(2.33GHz)
E3100
(3GHz)
X3220
(2.40GHz)
X3320
(2.50GHz)
Number of cores 2 4
L2 Cache Size 2MB 4MB 6MB 2x4MB 6MB
FSB 800MHz 1333MHz 1066MHz 1333MHz
CPU
Number of CPUs Standard :1(Maximum:1)
Security chip Complied with TCG 1.2
■ Supported OS（Page 207）
Addition
The supported operating systems for this server are as below.
• Windows Server 2003, Standard Edition (SP2 or later)
• Windows Server 2003, Standard x 64 Edition (SP2 or later)
• Windows Server 2003 R2, Standard Edition (SP2 or later)
• Windows Server 2003 R2, Standard x64 Edition (SP2 or later)
• Windows Small Business Server 2003 R2 (SP2 or later)
• Windows Small Business Server 2003 (SP2 or later)
• Windows Server 2008 Standard (32-bit)
• Windows Server 2008 Standard (64-bit)
• Red Hat Enterprise Linux ES (v.4 for x86)
• Red Hat Enterprise Linux ES (v.4 for EM64T)
• Red Hat Enterprise Linux 5 (for x86)
• Red Hat Enterprise Linux 5 (for Intel64)
For details of Windows Server 2008, refer to the "Support Matrix" at the following URL:
http://www.fujitsu.com/downloads/PRMRGY/support-matrix.pdf
All Rights Reserved, Copyright© FUJITSU LIMITED 2008
8／8
Autres manuels pour PRIMERGY TX150 S6
3
Table des matières
Autres manuels Fujitsu Serveur
Fujitsu
Fujitsu BS2000 SE Series Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY BX400 Manuel utilisateur
Fujitsu
Fujitsu SPARC EnterpriseM3000 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY BX620 S4 Manuel utilisateur
Fujitsu
Fujitsu PRIMEQUEST 2400E3 Instructions d'utilisation et d'entretien
Fujitsu
Fujitsu PRIMERGY TX150 S8 Guide de l'utilisateur
Fujitsu
Fujitsu SPARC Enterprise M3000 Manuel utilisateur
Fujitsu
Fujitsu Primergy TX120 Manuel utilisateur
Fujitsu
Fujitsu primequest 2400E2 Mode d’emploi
Fujitsu
Fujitsu Primergy TX300 S4 Mode d’emploi
Fujitsu
Fujitsu PRIMERGY RX2520 M1 Manuel utilisateur
Fujitsu
Fujitsu Primergy RX100 S2 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY RX2520 M4 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY TX200FT S2 Mode d’emploi
Fujitsu
Fujitsu SPARC Enterprise M4000 Guide d'installation
Fujitsu
Fujitsu PRIMERGY BX600 PG-LNB101 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY RX4770 M6 Manuel utilisateur
Fujitsu
Fujitsu PRIMERGY BX600 S3 Instructions d'installation
Fujitsu
Fujitsu Primergy RX300 S4 Manuel utilisateur
Fujitsu
Fujitsu BX630 - PRIMERGY - S2 Dual Manuel du propriétaire
